Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

华南师范大学学报(自然科学版)

Microwave Electric Field Measurement Based on Electromagnetically-Induced Transparency and Absorption in Atomic Vapor Cell at Room Temperature

Xiaohong Liu, Jie Liang, Changjun Chen, Huang Wei, Kai-Yu Liao

Published Jun 25, 2020• 0 citations
Publisher

Abstract

The traceability of microwave electric field is measured based on the Rydberg atomic quantum interference effect. The rubidium atomic vapor cell at room temperature is used as the probe, and the Autler-Townes splitting of two-photon electromagnetically-induced transparency, three-photon electromagnetically-induced transparency and three-photon electromagnetically-induced absorption effect are analyzed theoretically. The measurement limit of atomic shot noise is also discussed. This method is not only suitable for the traceability and self-calibration measurement of the microwave electric field but also for the sub-wavelength imaging and vector measurement of the microwave electric field and will provide a reference for further miniaturization and integration of the atomic microwave probe.

DOI
10.6054/j.jscnun.2020037

Related papers

Toward the Measurement of Microwave Electric Field Using Cesium Vapor MEMS Cell

Rui Zhao, Mengyang Feng, Jingtong Zhu +6 more

In this letter, we demonstrate an approach for the measurement of microwave electric field intensity based on Rydberg electromagnetically induced transparency (EIT)– Autler Townes (AT) splitting effect using a cesium vapor MEMS cell. The atomic absorption characteristics at different pump powers were obtained experimentally, which proved the feasibility of fabricated cesium vapor MEMS cell. The dependence of EIT-AT splitting separations on the microwave electric field intensities at 23.887 GHz was investigated at room temperature, and the minimum microwave electric field was measured to be 2 V/m. This approach indicates that the prepared cesium vapor MEMS cell can be qualified for microwave electric field intensity measurement, and has tremendous potential for the development of integrating quantum microwave field intensity meters.

IEEE Electron Device Letters•Oct 5, 2023•17 citations

Broadband Rydberg atom-based radio-frequency field sensor

Jiao Yue-Chun, Jianming Zhao, Jia Suo-Tang

Significant progress has been made in atom-based measurements of length, time, gravity and electromagnetic fields in recently years. Rydberg atom-based microwave electric field measurement, using electromagnetically induced transparency (EIT) in room temperature alkali-metal vapors, has been extensively investigated and aroused the broad interest. This approach may establish a new standard for the measurements of microwave (MW) and radio frequency (RF) electric fields.In this review, we describe the work on a new method of measuring electric fields based on quantum interference by using either cesium or rubidium atoms contained in a dielectric vapor cell. Rydberg atoms with principal quantum number n >>1 have large direct current (DC) polarizabilities and microwave transition dipole moments, thereby making them extremely sensitive to external electric fields. Using the Rydberg three-level EIT to detect the level splitting and shift that is induced by the external field, we can realize a rapid and robust self-calibration method of measuring the electric field in a frequency range from 0.01 GHz to 1000 GHz. For the MW electric field (frequency range > 1 GHz), the MW field causes the Rydberg states to split, known as an Autler-Townes splitting (A-T) effect when the applied microwave can resonate with adjacent Rydberg states. The MW coupled A-T splitting is proportional to the applied electric field strength, from which the field strength is measured. Using the EIT window, a high sensitivity of 3 μV·cm-1·Hz-1/2 and small electric field of 1 μV/cm are expected to be achieved with a modest setup, and the limitations of the sensitivity are also addressed in the review. For the RF field at frequency mj EIT lines, and avoided crossings formed with the fine-structure levels of equal mj and different J's, which is used to calibrate and measure the RF field amplitude. On the other hand, the dependence of the EIT-line strength on the RF field polarization provides a fast and robust polarization measurement of RF fields based on matching experimental data with a theoretical simulation. The measurements of minimum strengths and sensitivity of RF fields based on Rydberg atoms are one order magnitude below the values obtained by traditional antenna methods. The atom-based field measurement paves the way for determining fields through calibration-free, invariable atomic properties and miniaturization. We also propose its various potential applications in the future.

Acta Physica Sinica•Jan 1, 2018•7 citations

Simultaneously measuring microwave electric fields at different frequencies by Rydberg-atom-based electrometry with Zeeman-resolved Autler–Townes splitting

Yuxiang Wang, Yuqing Liu, Qianyi Zhang +5 more

We provide the simultaneous traceable measurements of microwave electric fields at two different frequencies by the electromagnetically induced transparency (EIT) and Autler–Townes (AT) splitting. A static magnetic field working together with a linearly polarized probe and coupling light prepares Rydberg atoms in Zeeman sublevels with maximal |mJ| in an atomic vapor cell. Using the EIT-AT splitting of these two maximal |mJ| states, the microwave electric fields at two different frequencies are simultaneously measured, in which their frequency difference can be adjustable within the linear range of magnetic field-induced level shifts. The proposed method provides a promising prospect for calibrating multiple microwave frequencies simultaneously in the future.

AIP Advances•Oct 1, 2024•6 citations

Microwave electric field sensing with Rydberg atoms

Daniel T. Stack, Paul D. Kunz, David H. Meyer +1 more

Atoms form the basis of precise measurement for many quantities (time, acceleration, rotation, magnetic field, etc.). Measurements of microwave frequency electric fields by traditional methods (i.e. engineered antennas) have limited sensitivity and can be difficult to calibrate properly. Highly-excited (Rydberg) neutral atoms have very large electric-dipole moments and many dipole allowed transitions in the range of 1 - 500 GHz. It is possible to sensitively probe the electric field in this range using the combination of two quantum interference phenomena: electromagnetically induced transparency and the Autler-Townes effect. This technique allows for very sensitive field amplitude, polarization, and sub-wavelength imaging measurements. These quantities can be extracted by measuring properties of a probe laser beam as it passes through a warm rubidium vapor cell. Thus far, Rydberg microwave electrometry has relied upon the absorption of the probe laser. We report on our use of polarization rotation, which corresponds to the real part of the susceptibility, for measuring the properties of microwave frequency electric fields. Our simulations show that when a magnetic field is present and directed along the optical propagation direction a polarization rotation signal exists and can be used for microwave electrometry. One central advantage in using the polarization rotation signal rather than the absorption signal is that common mode laser noise is naturally eliminated leading to a potentially dramatic increase in signal-to-noise ratio.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•May 19, 2016•3 citations

Microwave electrometry via electromagnetically induced absorption in cold Rydberg atoms

Kai-Yu Liao, Hai-Tao Tu, Shu-Zhe Yang +6 more

The atom-based traceable standard for microwave electrometry shows promising advantages by enabling stable and uniform measurement. Here we theoretically propose and then experimentally realize an alternative direct International System of Units (SI)--traceable and self-calibrated method for measuring a microwave-electric-field strength based on electromagnetically induced absorption (EIA) in cold Rydberg atoms. Comparing with the method of electromagnetically induced transparency, we show that the equivalence relation between the microwave Rabi frequency and Autler-Townes splitting is more valid and is even more robust against the experimental parameters in the EIA's linear region. Furthermore, a narrower linewidth of cold Rydberg EIA enables us to realize a direct SI-traceable microwave-electric-field measurement as small as $\ensuremath{\sim}100\phantom{\rule{4pt}{0ex}}\ensuremath{\mu}\mathrm{V}\phantom{\rule{0.16em}{0ex}}{\mathrm{cm}}^{\ensuremath{-}1}$.

arXiv:2002.00855•Physical Review A•May 21, 2020•119 citations

Spatial distribution measurement of the microwave electric field strength via the Autler-Townes effect of Rydberg atom

Jiasheng Liu, Hao Zhang, Zhenfei Song +2 more

We demonstrate the high-resolution spatial feature measurement of microwave electric field using an cesium atomic vapor cell based on the electromagnetically induced transparency (EIT) spectrum of133Cs Rydberg atom. The microwave electric field with the frequency of 6.95 GHz couples the transition of 47D5/2→48P3/2 Rydberg states. The EIT spectrum of a 6S1/2-6P3/2-47D5/2 ladder system will split by the Autler-Townes(AT) effect under the microwave electric field. The dependence of AT splitting separation on the microwave electric fields strength is observed. Moreover, we present the imaging of the spatial feature of microwave electric field in the atomic vapor cell. The theoretical maximum spatial resolution is about λMw/430.

IEEE MTT-S International Conference on Numerical Electromagnetic and Multiphysics Modeling and Optimization•Jul 1, 2016•1 citation
The traceability of microwave electric field is measured based on the Rydberg atomic quantum interference effect. The rubidium atomic vapor cell at room temperature is used as the probe, and the Autler-Townes splitting of two-photon electromagnetically-induced transparency, three-photon electromagnetically-induced transparency and three-photon electromagnetically-induced absorption effect are analyzed theoretically. The measurement limit of atomic shot noise is also discussed. This method is not only suitable for the traceability and self-calibration measurement of the microwave electric field but also for the sub-wavelength imaging and vector measurement of the microwave electric field and will provide a reference for further miniaturization and integration of the atomic microwave probe.
In this letter, we demonstrate an approach for the measurement of microwave electric field intensity based on Rydberg electromagnetically induced transparency (EIT)– Autler Townes (AT) splitting effect using a cesium vapor MEMS cell. The atomic absorption characteristics at different pump powers were obtained experimentally, which proved the feasibility of fabricated cesium vapor MEMS cell. The dependence of EIT-AT splitting separations on the microwave electric field intensities at 23.887 GHz was investigated at room temperature, and the minimum microwave electric field was measured to be 2 V/m. This approach indicates that the prepared cesium vapor MEMS cell can be qualified for microwave electric field intensity measurement, and has tremendous potential for the development of integrating quantum microwave field intensity meters.
Significant progress has been made in atom-based measurements of length, time, gravity and electromagnetic fields in recently years. Rydberg atom-based microwave electric field measurement, using electromagnetically induced transparency (EIT) in room temperature alkali-metal vapors, has been extensively investigated and aroused the broad interest. This approach may establish a new standard for the measurements of microwave (MW) and radio frequency (RF) electric fields.In this review, we describe the work on a new method of measuring electric fields based on quantum interference by using either cesium or rubidium atoms contained in a dielectric vapor cell. Rydberg atoms with principal quantum number n >>1 have large direct current (DC) polarizabilities and microwave transition dipole moments, thereby making them extremely sensitive to external electric fields. Using the Rydberg three-level EIT to detect the level splitting and shift that is induced by the external field, we can realize a rapid and robust self-calibration method of measuring the electric field in a frequency range from 0.01 GHz to 1000 GHz. For the MW electric field (frequency range > 1 GHz), the MW field causes the Rydberg states to split, known as an Autler-Townes splitting (A-T) effect when the applied microwave can resonate with adjacent Rydberg states. The MW coupled A-T splitting is proportional to the applied electric field strength, from which the field strength is measured. Using the EIT window, a high sensitivity of 3 μV·cm-1·Hz-1/2 and small electric field of 1 μV/cm are expected to be achieved with a modest setup, and the limitations of the sensitivity are also addressed in the review. For the RF field at frequency mj EIT lines, and avoided crossings formed with the fine-structure levels of equal mj and different J's, which is used to calibrate and measure the RF field amplitude. On the other hand, the dependence of the EIT-line strength on the RF field polarization provides a fast and robust polarization measurement of RF fields based on matching experimental data with a theoretical simulation. The measurements of minimum strengths and sensitivity of RF fields based on Rydberg atoms are one order magnitude below the values obtained by traditional antenna methods. The atom-based field measurement paves the way for determining fields through calibration-free, invariable atomic properties and miniaturization. We also propose its various potential applications in the future.
We provide the simultaneous traceable measurements of microwave electric fields at two different frequencies by the electromagnetically induced transparency (EIT) and Autler–Townes (AT) splitting. A static magnetic field working together with a linearly polarized probe and coupling light prepares Rydberg atoms in Zeeman sublevels with maximal |mJ| in an atomic vapor cell. Using the EIT-AT splitting of these two maximal |mJ| states, the microwave electric fields at two different frequencies are simultaneously measured, in which their frequency difference can be adjustable within the linear range of magnetic field-induced level shifts. The proposed method provides a promising prospect for calibrating multiple microwave frequencies simultaneously in the future.
Atoms form the basis of precise measurement for many quantities (time, acceleration, rotation, magnetic field, etc.). Measurements of microwave frequency electric fields by traditional methods (i.e. engineered antennas) have limited sensitivity and can be difficult to calibrate properly. Highly-excited (Rydberg) neutral atoms have very large electric-dipole moments and many dipole allowed transitions in the range of 1 - 500 GHz. It is possible to sensitively probe the electric field in this range using the combination of two quantum interference phenomena: electromagnetically induced transparency and the Autler-Townes effect. This technique allows for very sensitive field amplitude, polarization, and sub-wavelength imaging measurements. These quantities can be extracted by measuring properties of a probe laser beam as it passes through a warm rubidium vapor cell. Thus far, Rydberg microwave electrometry has relied upon the absorption of the probe laser. We report on our use of polarization rotation, which corresponds to the real part of the susceptibility, for measuring the properties of microwave frequency electric fields. Our simulations show that when a magnetic field is present and directed along the optical propagation direction a polarization rotation signal exists and can be used for microwave electrometry. One central advantage in using the polarization rotation signal rather than the absorption signal is that common mode laser noise is naturally eliminated leading to a potentially dramatic increase in signal-to-noise ratio.
The atom-based traceable standard for microwave electrometry shows promising advantages by enabling stable and uniform measurement. Here we theoretically propose and then experimentally realize an alternative direct International System of Units (SI)--traceable and self-calibrated method for measuring a microwave-electric-field strength based on electromagnetically induced absorption (EIA) in cold Rydberg atoms. Comparing with the method of electromagnetically induced transparency, we show that the equivalence relation between the microwave Rabi frequency and Autler-Townes splitting is more valid and is even more robust against the experimental parameters in the EIA's linear region. Furthermore, a narrower linewidth of cold Rydberg EIA enables us to realize a direct SI-traceable microwave-electric-field measurement as small as $\ensuremath{\sim}100\phantom{\rule{4pt}{0ex}}\ensuremath{\mu}\mathrm{V}\phantom{\rule{0.16em}{0ex}}{\mathrm{cm}}^{\ensuremath{-}1}$.
We demonstrate the high-resolution spatial feature measurement of microwave electric field using an cesium atomic vapor cell based on the electromagnetically induced transparency (EIT) spectrum of133Cs Rydberg atom. The microwave electric field with the frequency of 6.95 GHz couples the transition of 47D5/2→48P3/2 Rydberg states. The EIT spectrum of a 6S1/2-6P3/2-47D5/2 ladder system will split by the Autler-Townes(AT) effect under the microwave electric field. The dependence of AT splitting separation on the microwave electric fields strength is observed. Moreover, we present the imaging of the spatial feature of microwave electric field in the atomic vapor cell. The theoretical maximum spatial resolution is about λMw/430.