Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Characterising the effective temperature of hybrid tunnel junctions in THz SIS mixers

Alessandro Traini, Boon-Kok Tan, John Garrett, Andrey V. Khudchenko, Ronald Hesper, A. M. Baryshev, Pavel Dmitriev, V. P. Koshelets, G. Yassin

Published Jan 1, 2021• 0 citations
OpenAlex

Abstract

In this paper, we present a method to measure the effective physical temperature of the tunnel junction in a terahertz superconductor-insulator-superconductor (SIS) mixer when illuminated with a strong local oscillator (LO) power that results in local hot spot around the tunnel junction. We observed that the gap voltage of the pumped current-voltage (IV) curve is suppressed when the LO pumping level is increased, indicating that the junction physical temperature is increased beyond the mixer block temperature. We quantified this extra heating effect by recovering the effective junction temperature through comparing the gap voltage of the pumped IV curves measured at a fixed block temperature, with the unpumped IV curve measured at varying block temperatures. We found that the heat trapped in the tunnel junction can be as high as 1.7 K when the mixer stabilised at 3.3 K is pumped at only 21% of the gap current.

Related papers

The Influence of LO Power Heating of the Tunnel Junction on the Performance of THz SIS Mixers

Alessandro Traini, Boon-Kok Tan, John Garrett +6 more

We describe the performance of a superconductor- insulator-superconductor (SIS) mixer operating in the frequency range of 780-950 GHz. Unlike most SIS mixers, the tunnel junction employs two different superconductors, a niobium nitride top and a niobium bottom electrode sandwiching an aluminum nitride barrier layer, fabricated on a niobium titanium nitride ground plane. The mixer was tested in a pulse tube cryostat, with all the optical components, in the signal path, mounted inside the vacuum environment to avoid attenuation of the RF signal as it propagates from the hot/cold loads to the mixer. With this setup, we have measured an RF-corrected noise temperature of ~220 K. In this article, we focus on investigating the influence of local oscillator (LO) power heating on the performance of the terahertz mixer. The increase in the junction's physical temperature can be observed experimentally by noting the suppression of the gap voltage in the pumped current-voltage (I-V ) curve as the LO pumping level is increased. Similar observation has already been reported, and attempts were made to estimate the effective temperature of the device using equations of heat transfer between the mixer chip layers. Here, we present an experimental method of quantifying this effect by recovering the effective temperature of the junction through comparing the pumped I-V curves at different pumping levels and fixed bath temperature, with the unpumped I-V curves obtained at varying bath temperatures. We also estimate, for the first time, the effect of heating on the noise temperature as a function of bath temperature and frequency. We show that for typical experimental parameters, the LO heating can increase the double-sideband receiver noise temperature by as much as 20%, and that in the frequency range of the measurements, the effective temperature of the junction at fixed LO power increases linearly with frequency at a rate of 0.5 K/100 GHz.

IEEE Transactions on Terahertz Science and Technology•Sep 30, 2020•5 citations

Direct current heating in superconductor–insulator–superconductor tunnel devices for THz mixing applications

Pieter Dieleman, T. M. Klapwijk, Sergey Kovtonyuk +1 more

DC heating effects in superconductor–insulator–superconductor (SIS) tunnel junctions are studied by comparing junctions sandwiched between niobium or aluminum layers. With niobium a temperature rise of several Kelvin is observed, which is reduced by an order of magnitude by using aluminum. A simple model satisfactorily explains this observation and predicts a 30% increase in the subgap current due to the elevated temperature. At the operating voltage for heterodyne mixing the receiver noise temperature increases by only 2%.

Applied Physics Letters•Jul 15, 1996•15 citations

Hot electron effect in terahertz hybrid devices

Bruno Leone, J. R. Gao, T. M. Klapwijk +3 more

We analyse both the direct current and submillimeter pumped current-voltage characteristics of a hybrid superconductor-insulator-superconductor terahertz mixer consisting of a Nb tunnel junction integrated with NbTiN tuning striplines. We find that the presence of the Nb/NbTiN interface gives rise to a hot electron effect. The assumption of an equilibrium electron temperature, as distinct from the phonon temperature, allows a complete understanding of the processes involved. The impact of the hot electron effect on superconducting terahertz detectors is discussed.

IEEE Transactions on Applied Superconductivity•Mar 1, 2001•7 citations

Terahertz high-sensitivity SIS mixer based on Nb–AlN–NbN hybrid superconducting tunnel junctions

Bo-Liang 博梁 Liu 刘, Dong 冬 Liu 刘, Ming Yao +8 more

The terahertz band, a unique segment of the electromagnetic spectrum, is crucial for observing the cold, dark universe and plays a pivotal role in cutting-edge scientific research, including the study of cosmic environments that support life and imaging black holes. High-sensitivity superconductor–insulator–superconductor (SIS) mixers are essential detectors for terahertz astronomical telescopes and interferometric arrays. Compared to the commonly used classical Nb/AlO x /Nb superconducting tunnel junction, the Nb/AlN/NbN hybrid superconducting tunnel junction has a higher energy gap voltage and can achieve a higher critical current density. This makes it particularly promising for the development of ultra-wideband, high-sensitivity coherent detectors or mixers in various scientific research fields. In this paper, we present a superconducting SIS mixer based on Nb/AlN/NbN parallel-connected twin junctions (PCTJ), which has a bandwidth extending up to 490 GHz–720 GHz. The best achieved double-sideband (DSB) noise temperature (sensitivity) is below three times the quantum noise level.

Chinese Physics B•Feb 22, 2024•6 citations

DC heating in SIS tunnel devices for THz mixing applications.

Pieter Dieleman, T. M. Klapwijk, Sergey Kovtonyuk +1 more

Heating effects in Superconductor- Insulator- Superconductor (SIS) tunnel junctions are studied by comparing SIS junctions equipped with niobium and aluminum electrodes. A temperature rise of several K is observed with niobium, which is reduced by an order of magnitude with aluminum. A simple model satisfactorily explains this observation and predicts an increase in the noise temperature of up to 30% at the operating voltage for heterodyne mixing due to this effect.

•Jan 1, 1995•0 citations

An analytic investigation of the superconductor quasiparticle mixer in the low power limit

M. J. Feldman

The properties of an SIS (Superconductor-insulator-superconductor) mixer using a slightly nonideal junction, with finite local oscillator (LO) power, are determined by analytic expansion of the equations of the quantum theory of mixing. The result is that the conversion gain using any reasonably good quality SIS junction is essentially equal to that using a perfect junction. Quite to the contrary, the minimum noise temperature is controlled by the leakage current of the junction: the increase in the minimum added-noise temperature over the quantum limit T/sub Q/=h omega /2k is given by delta T/sub Q/=(h omega /k) square root I/sub 0/I/sub 2//I/sub 1/; this minimum requires that the LO voltage across the junction is V/sub LO/=(64I/sub 0//I/sub 2/) /sup 1/4/h omega /e. (I/sub n/ is the current measured on the unpumped I-V curve of the junction at voltage V/sub 0/+nh omega /e). Therefore, although an SIS mixer using an ideal junction can reach the quantum noise limit only in the limit of zero LO power, even the most nearly ideal junctions require a considerable LO for best sensitivity.

IEEE Transactions on Magnetics•Mar 1, 1991•11 citations
In this paper, we present a method to measure the effective physical temperature of the tunnel junction in a terahertz superconductor-insulator-superconductor (SIS) mixer when illuminated with a strong local oscillator (LO) power that results in local hot spot around the tunnel junction. We observed that the gap voltage of the pumped current-voltage (IV) curve is suppressed when the LO pumping level is increased, indicating that the junction physical temperature is increased beyond the mixer block temperature. We quantified this extra heating effect by recovering the effective junction temperature through comparing the gap voltage of the pumped IV curves measured at a fixed block temperature, with the unpumped IV curve measured at varying block temperatures. We found that the heat trapped in the tunnel junction can be as high as 1.7 K when the mixer stabilised at 3.3 K is pumped at only 21% of the gap current.
We describe the performance of a superconductor- insulator-superconductor (SIS) mixer operating in the frequency range of 780-950 GHz. Unlike most SIS mixers, the tunnel junction employs two different superconductors, a niobium nitride top and a niobium bottom electrode sandwiching an aluminum nitride barrier layer, fabricated on a niobium titanium nitride ground plane. The mixer was tested in a pulse tube cryostat, with all the optical components, in the signal path, mounted inside the vacuum environment to avoid attenuation of the RF signal as it propagates from the hot/cold loads to the mixer. With this setup, we have measured an RF-corrected noise temperature of ~220 K. In this article, we focus on investigating the influence of local oscillator (LO) power heating on the performance of the terahertz mixer. The increase in the junction's physical temperature can be observed experimentally by noting the suppression of the gap voltage in the pumped current-voltage (I-V ) curve as the LO pumping level is increased. Similar observation has already been reported, and attempts were made to estimate the effective temperature of the device using equations of heat transfer between the mixer chip layers. Here, we present an experimental method of quantifying this effect by recovering the effective temperature of the junction through comparing the pumped I-V curves at different pumping levels and fixed bath temperature, with the unpumped I-V curves obtained at varying bath temperatures. We also estimate, for the first time, the effect of heating on the noise temperature as a function of bath temperature and frequency. We show that for typical experimental parameters, the LO heating can increase the double-sideband receiver noise temperature by as much as 20%, and that in the frequency range of the measurements, the effective temperature of the junction at fixed LO power increases linearly with frequency at a rate of 0.5 K/100 GHz.
DC heating effects in superconductor–insulator–superconductor (SIS) tunnel junctions are studied by comparing junctions sandwiched between niobium or aluminum layers. With niobium a temperature rise of several Kelvin is observed, which is reduced by an order of magnitude by using aluminum. A simple model satisfactorily explains this observation and predicts a 30% increase in the subgap current due to the elevated temperature. At the operating voltage for heterodyne mixing the receiver noise temperature increases by only 2%.
We analyse both the direct current and submillimeter pumped current-voltage characteristics of a hybrid superconductor-insulator-superconductor terahertz mixer consisting of a Nb tunnel junction integrated with NbTiN tuning striplines. We find that the presence of the Nb/NbTiN interface gives rise to a hot electron effect. The assumption of an equilibrium electron temperature, as distinct from the phonon temperature, allows a complete understanding of the processes involved. The impact of the hot electron effect on superconducting terahertz detectors is discussed.
The terahertz band, a unique segment of the electromagnetic spectrum, is crucial for observing the cold, dark universe and plays a pivotal role in cutting-edge scientific research, including the study of cosmic environments that support life and imaging black holes. High-sensitivity superconductor–insulator–superconductor (SIS) mixers are essential detectors for terahertz astronomical telescopes and interferometric arrays. Compared to the commonly used classical Nb/AlO x /Nb superconducting tunnel junction, the Nb/AlN/NbN hybrid superconducting tunnel junction has a higher energy gap voltage and can achieve a higher critical current density. This makes it particularly promising for the development of ultra-wideband, high-sensitivity coherent detectors or mixers in various scientific research fields. In this paper, we present a superconducting SIS mixer based on Nb/AlN/NbN parallel-connected twin junctions (PCTJ), which has a bandwidth extending up to 490 GHz–720 GHz. The best achieved double-sideband (DSB) noise temperature (sensitivity) is below three times the quantum noise level.
The properties of an SIS (Superconductor-insulator-superconductor) mixer using a slightly nonideal junction, with finite local oscillator (LO) power, are determined by analytic expansion of the equations of the quantum theory of mixing. The result is that the conversion gain using any reasonably good quality SIS junction is essentially equal to that using a perfect junction. Quite to the contrary, the minimum noise temperature is controlled by the leakage current of the junction: the increase in the minimum added-noise temperature over the quantum limit T/sub Q/=h omega /2k is given by delta T/sub Q/=(h omega /k) square root I/sub 0/I/sub 2//I/sub 1/; this minimum requires that the LO voltage across the junction is V/sub LO/=(64I/sub 0//I/sub 2/) /sup 1/4/h omega /e. (I/sub n/ is the current measured on the unpumped I-V curve of the junction at voltage V/sub 0/+nh omega /e). Therefore, although an SIS mixer using an ideal junction can reach the quantum noise limit only in the limit of zero LO power, even the most nearly ideal junctions require a considerable LO for best sensitivity.