Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

SPECTROSCOPY OF TWO LEVEL DEFECTS & QUASIPARTICLES IN SUPERCONDUCTING RESONATORS

Timothy Kohler

Published Jan 1, 2021• 0 citations
Publisher

Abstract

Superconducting films are inherently limited by losses due to two-level system (TLS) defects within the amorphous oxide layers surrounding them and from quasiparticles in the film. In this thesis I will discuss novel theoretical and experimental methods toward understanding superconducting resonator loss from deleterious surface TLS defects as well as a loss transition from non-equilibrium quasiparticles in granular TiN. I will show using finite element solver software that a resonator with submicron linewidth and linespacing can be used to better characterize and simulate surface TLS as part of a circuit QED system. I have observed individual surface TLS and found coupling values in the range of g/2π =50 kHz -280 kHz with a maximum dipole moment pz-max = 4.5 Debye (.93 eÅ). I have found in in simulation of experiment that over 80% of the strongly coupled TLS reside within 50 nm of the corner between the Metal-Substrate (MS) and Substrate-Air (SA) interface. Additionally I have studied a loss transition from non-equilibrium quasiparticles in TiN films. These films exhibit an anomalous loss dependence on substrate treatment and film thickness. The films of interest are ones grown thin on oxidized substrates, which exhibit an order of magnitude decrease in internal quality factor (Qi) relative to either thicker ˝films or films grown without the oxidized substrate. These films additionally exhibit a grain size on average of 7.5 nm, a higher inhomogeneous gap, a transition to lower stress and a preference for the [111] crystal growth. The temperature dependence of the conductivity is fit and a factor of two difference in quasiparticle lifetime is found between the two films where the thinner film has a shorter lifetime. A two gap quasiparticle trapping model is fit to the temperature dependent loss data. The data is consistent with a model where non-equilibrium quasi-particles are trapped in low gapped grains on the inside of the films. From these works and others presented in my thesis the understanding of TLSs on surfaces and non-equilibrium quasiparticles in TiN has improved. This will help illuminate some of the most important absorption mechanisms plaguing superconducting qubits and resonators.

DOI
10.13016/trei-78bx

Related papers

Modeling Dielectric Loss in Superconducting Resonators: Evidence for Interacting Atomic Two-Level Systems at the Nb/Oxide Interface

Noah Gorgichuk, Tobias Junginger, Rogério de Sousa

While several experiments claim that two-level system (TLS) defects in amorphous surfaces and interfaces are responsible for energy relaxation in superconducting resonators and qubits, none can provide quantitative explanation of their data in terms of the conventional noninteracting TLS model. Here a model that interpolates between the interacting and noninteracting TLS loss tangent is proposed to perform numerical analysis of experimental data and extract information about TLS parameters and their distribution. As a proof of principle, the model is applied to TESLA cavities that contain only a single lossy material in their interior, the niobium-niobium oxide interface. The best fits show interacting TLSs with a sharp modulus of electric dipole moment for both thin ($5\phantom{\rule{0.2em}{0ex}}\mathrm{nm}$) and thick ($100\phantom{\rule{0.2em}{0ex}}\mathrm{nm}$) oxides, indicating that the TLSs are ``atomic'' instead of ``glassy.'' The proposed method can be applied to other devices with multiple material interfaces and substrates, with the goal of elucidating the nature of TLSs causing energy loss in resonators and qubits.

arXiv:2203.05054•Physical Review Applied•Feb 2, 2023•15 citations

The effect of niobium thin film structure on losses in superconducting circuits

Maxwell Drimmer, Sjoerd Telkamp, Felix L Fischer +7 more

Abstract The performance of superconducting microwave circuits is strongly influenced by the material properties of the superconducting film and substrate. While progress has been made in understanding the importance of surface preparation and the effect of surface oxides, the complex effect of superconductor film structure on microwave losses is not yet fully understood. In this study, we investigate the microwave properties of niobium resonators with different crystalline properties and related surface topographies. We analyze a series of magnetron sputtered films in which the Nb crystal orientation and surface topography are changed by varying the substrate temperatures between room temperature and 975 K. The lowest-loss resonators that we measure have quality factors of over 10 6 at single-photon powers, among the best ever recorded using the Nb on sapphire platform. We observe the highest quality factors in films grown at an intermediate temperature regime of the growth series (550 K) where the films display both preferential ordering of the crystal domains and low surface roughness. Furthermore, we analyze the temperature-dependent behavior of our resonators to learn about how the quasiparticle density in the Nb film is affected by the niobium crystal structure and the presence of grain boundaries. Our results stress the connection between the crystal structure of superconducting films and the loss mechanisms suffered by the resonators and indicate that even a moderate change in temperature during thin film deposition can significantly affect the resulting quality factors.

arXiv:2403.12164•Materials for Quantum Technology•Oct 14, 2025•22 citations

Analysis of high quality superconducting resonators: consequences for TLS properties in amorphous oxides

Jonathan Burnett, Lara Faoro, T Lindström

noise caused by microscopic two-level systems (TLS) is known to be very detrimental to the performance of superconducting quantum devices but the nature of these TLS is still poorly understood. Recent experiments with superconducting resonators indicates that interaction between TLS in the oxide at the film-substrate interface is not negligible. Here we present data on the loss and frequency noise from two different Nb resonators with and without Pt capping and discuss what conclusions can be drawn regarding the properties of TLS in amorphous oxides. We also estimate the concentration and dipole moment of the TLS.

arXiv:1512.02553•Superconductor Science and Technology•Mar 11, 2016•81 citations

LOSS IN SUPERCONDUCTING QUANTUM DEVICES FROM NON-EQUILIBRIUM QUASIPARTICLES AND INHOMOGENEITY IN ENERGY GAP

Rui Zhang

This dissertation describes energy dissipation and microwave loss due to non-equilibrium quasiparticles in superconducting transmon qubits and titanium nitride coplanar waveguide resonators. During the measurements of transmon T1 relaxation time and resonator quality factor QI, I observed reduced microwave loss as the temperature increased from 20 mK to approximately Tc/10 at which the loss takes on a minimum value. I argue that this effect is due to non-equilibrium quasiparticles. I measured the temperature dependence of the relaxation time T1 of the excited state of an Al/AlOx/Al transmon and found that, in some cases, T1 increased by almost a factor of two as the temperature increased from 30 mK to 100 mK with a best T1 of 0.2 ms. I present an argument showing this unexpected temperature dependence occurs due to the behavior of non-equilibrium quasiparticles in devices in which one electrode in the tunnel junction has a smaller volume, and slightly smaller superconducting energy gap, than the other electrode. At sufficiently low temperatures, non-equilibrium quasiparticles accumulate in the electrode with the smaller gap, leading to a relatively high density of quasiparticles at the junction and a short T1. Increasing the temperature gives the quasiparticles enough thermal energy to occupy the higher gap electrode, reducing the density at the junction and increasing T1. I present a model of this effect, extract the density of quasiparticles and the two superconducting energy gaps, and discuss implications for increasing the relaxation time of transmons. I also observed a similar phenomenon in low temperature microwave studies of titanium nitride coplanar waveguide resonators. I report on loss in a resonator at temperatures from 20 mK up to 1.1 K and with the application of infrared pair breaking radiation (λ=1.55 μm). With no applied IR light, the internal quality factor increased from QI = 800,000 at T < 70 mK up to QI=(2×10^6 ) at 600 mK. The resonant frequency f0 increased by 2 parts per million over the same temperature range. Above 600 mK both QI and f0 decreased rapidly, consistent with the increase in the density of thermally generated quasiparticles. With the application of IR light and for intensities below 1 aW μm^(-2) and T < 400 mK, QI increased in a similar way to increasing the temperature before beginning to decrease with larger intensities. I show that a model involving non-equilibrium quasiparticles and two regions of different superconducting gaps can explain this unexpected behavior.

•Jan 1, 2020•2 citations

Vanadium superconducting microwave resonators on silicon wafers

Y. Fujita, Y. Urade, Y. Hibino +4 more

Understanding the correlation between material properties and microwave losses in superconducting films is a crucial subject for developing low-loss materials for quantum circuits. We focus on vanadium (V) as a novel material for superconducting quantum devices and discuss loss in V films in relation to their structural properties. Using a sputtering method, we grow four V-film structures on (001)-oriented Si wafers, employing Nb and Ta as the buffer and capping layer materials, respectively: Nb/V/Ta, Nb/V, V/Ta, and V. X-ray diffraction and atomic force microscopy reveal that the V films grown on the Nb buffer layers have higher uniformity of lattice orientation and smaller grain size than that directly grown on the Si wafer. Coplanar waveguide resonators are fabricated from the four V-film structures, and averaged photon number ($\langle n_{\rm ph} \rangle$) dependences of internal quality factor ($Q_{\rm int}$) are obtained by performing microwave measurements. By analyzing the obtained $Q_{\rm int}$ vs $\langle n_{\rm ph} \rangle$, it is found that loss at the V surface is dominated by $\langle n_{\rm ph} \rangle$-independent non-two-level-system (non-TLS) losses, which can be mitigated by introducing the Ta capping layer. Furthermore, the V films on the Nb buffer layers exhibit lower $Q_{\rm int}$ in the $\langle n_{\rm ph} \rangle$ range from 10$^{0}$ to 10$^{6}$ and higher non-TLS loss than that directly grown on Si wafers, even though the former has higher lattice-orientation uniformity than the latter. Origins of these trends might be relevant to V oxides, of which presence at surfaces and grain boundaries in bulk regions in the V resonators is suggested by energy dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy, and/or V hydrides.

cond-mat.mtrl-sciCross-listedarXiv:2607.00809•Jul 2, 2026•0 citations

Low-temperature characterization of dielectric loss at microwave frequencies in aluminum oxide

Martin R. Otto

Superconducting quantum devices have gained increasing interest over the past 15 years because of their role as promising candidates for implementing a large-scale quantum computer and as ultra-sensitive detectors. Superconducting resonators are one type of superconducting device which are used in a variety of applications including quantum computing and radioastronomy. They can achieve large quality factors which are important for these applications and a variety of others. Specific examples of these applications include the readout and coupling of superconducting qubits and also microwave kinetic inductance detector arrays for sub-mm wavelength astronomical measurements. High quality factors also enable the study of very subtle features in the electromagnetic response of the resonator. This feature in turn offers provides a method to characterize loss mechanisms which affect the performance of superconducting qubits, by measuring the quality factor of a resonator. Dielectric loss is an example of such a loss mechanism, and is considered to be one of, if not \\it the \\rm major obstacle to overcome in order to construct scalable quantum technologies based on superconducting devices. This type of loss arises from the coupling of the electric field in the device to spurious degrees of freedom which arise naturally the dielectric environment of the device. The fast-growing interest in the physics and applications of superconducting resonators has renewed interest in an improving our fundamental understanding of dielectric loss. This interest involves the study of a much bigger and older question in condensed matter physics; namely, what is the microscopic physics which governs the behaviour and of an amorphous material at low-temperatures? \n \nIn this thesis, we present a systematic study of dielectric loss in amorphous aluminum oxide using superconducting microwave resonators. Measurements of the intrinsic loss tangent over a large temperature range of 40~mK to 1~K are presented and analyzed in detail. Some aspects of the data are well understood in terms of the standard tunnelling two-level system model, while others require a deeper analysis of the electrodynamics of the resonator and insights from more advanced theories. We employ a consistent approach using numerical simulations of the resonator to understand loss mechanisms arising from both an inhomogeneous electric field and multiple dielectric layers. We measure saturation effects which provide insight into coherent properties of two-level system ensembles and the mutual interaction between them. Excellent agreement with the two-level system model is found for intrinsic losses, however the strong dependence on temperature which we observe for saturation effects is not predicted in the standard form of the model. We find that this dependence can be understood in terms of the theory of spectral diffusion which is consistent with a strong mutual interaction between two-level systems contributes to broadening of their spectral linewidths.

•Apr 9, 2015•1 citation
Superconducting films are inherently limited by losses due to two-level system (TLS) defects within the amorphous oxide layers surrounding them and from quasiparticles in the film. In this thesis I will discuss novel theoretical and experimental methods toward understanding superconducting resonator loss from deleterious surface TLS defects as well as a loss transition from non-equilibrium quasiparticles in granular TiN. I will show using finite element solver software that a resonator with submicron linewidth and linespacing can be used to better characterize and simulate surface TLS as part of a circuit QED system. I have observed individual surface TLS and found coupling values in the range of g/2π =50 kHz -280 kHz with a maximum dipole moment pz-max = 4.5 Debye (.93 eÅ). I have found in in simulation of experiment that over 80% of the strongly coupled TLS reside within 50 nm of the corner between the Metal-Substrate (MS) and Substrate-Air (SA) interface. Additionally I have studied a loss transition from non-equilibrium quasiparticles in TiN films. These films exhibit an anomalous loss dependence on substrate treatment and film thickness. The films of interest are ones grown thin on oxidized substrates, which exhibit an order of magnitude decrease in internal quality factor (Qi) relative to either thicker ˝films or films grown without the oxidized substrate. These films additionally exhibit a grain size on average of 7.5 nm, a higher inhomogeneous gap, a transition to lower stress and a preference for the [111] crystal growth. The temperature dependence of the conductivity is fit and a factor of two difference in quasiparticle lifetime is found between the two films where the thinner film has a shorter lifetime. A two gap quasiparticle trapping model is fit to the temperature dependent loss data. The data is consistent with a model where non-equilibrium quasi-particles are trapped in low gapped grains on the inside of the films. From these works and others presented in my thesis the understanding of TLSs on surfaces and non-equilibrium quasiparticles in TiN has improved. This will help illuminate some of the most important absorption mechanisms plaguing superconducting qubits and resonators.
While several experiments claim that two-level system (TLS) defects in amorphous surfaces and interfaces are responsible for energy relaxation in superconducting resonators and qubits, none can provide quantitative explanation of their data in terms of the conventional noninteracting TLS model. Here a model that interpolates between the interacting and noninteracting TLS loss tangent is proposed to perform numerical analysis of experimental data and extract information about TLS parameters and their distribution. As a proof of principle, the model is applied to TESLA cavities that contain only a single lossy material in their interior, the niobium-niobium oxide interface. The best fits show interacting TLSs with a sharp modulus of electric dipole moment for both thin (5nm5\phantom{\rule{0.2em}{0ex}}\mathrm{nm}5nm) and thick (100nm100\phantom{\rule{0.2em}{0ex}}\mathrm{nm}100nm) oxides, indicating that the TLSs are ``atomic'' instead of ``glassy.'' The proposed method can be applied to other devices with multiple material interfaces and substrates, with the goal of elucidating the nature of TLSs causing energy loss in resonators and qubits.
Abstract The performance of superconducting microwave circuits is strongly influenced by the material properties of the superconducting film and substrate. While progress has been made in understanding the importance of surface preparation and the effect of surface oxides, the complex effect of superconductor film structure on microwave losses is not yet fully understood. In this study, we investigate the microwave properties of niobium resonators with different crystalline properties and related surface topographies. We analyze a series of magnetron sputtered films in which the Nb crystal orientation and surface topography are changed by varying the substrate temperatures between room temperature and 975 K. The lowest-loss resonators that we measure have quality factors of over 10 6 at single-photon powers, among the best ever recorded using the Nb on sapphire platform. We observe the highest quality factors in films grown at an intermediate temperature regime of the growth series (550 K) where the films display both preferential ordering of the crystal domains and low surface roughness. Furthermore, we analyze the temperature-dependent behavior of our resonators to learn about how the quasiparticle density in the Nb film is affected by the niobium crystal structure and the presence of grain boundaries. Our results stress the connection between the crystal structure of superconducting films and the loss mechanisms suffered by the resonators and indicate that even a moderate change in temperature during thin film deposition can significantly affect the resulting quality factors.
noise caused by microscopic two-level systems (TLS) is known to be very detrimental to the performance of superconducting quantum devices but the nature of these TLS is still poorly understood. Recent experiments with superconducting resonators indicates that interaction between TLS in the oxide at the film-substrate interface is not negligible. Here we present data on the loss and frequency noise from two different Nb resonators with and without Pt capping and discuss what conclusions can be drawn regarding the properties of TLS in amorphous oxides. We also estimate the concentration and dipole moment of the TLS.
This dissertation describes energy dissipation and microwave loss due to non-equilibrium quasiparticles in superconducting transmon qubits and titanium nitride coplanar waveguide resonators. During the measurements of transmon T1 relaxation time and resonator quality factor QI, I observed reduced microwave loss as the temperature increased from 20 mK to approximately Tc/10 at which the loss takes on a minimum value. I argue that this effect is due to non-equilibrium quasiparticles. I measured the temperature dependence of the relaxation time T1 of the excited state of an Al/AlOx/Al transmon and found that, in some cases, T1 increased by almost a factor of two as the temperature increased from 30 mK to 100 mK with a best T1 of 0.2 ms. I present an argument showing this unexpected temperature dependence occurs due to the behavior of non-equilibrium quasiparticles in devices in which one electrode in the tunnel junction has a smaller volume, and slightly smaller superconducting energy gap, than the other electrode. At sufficiently low temperatures, non-equilibrium quasiparticles accumulate in the electrode with the smaller gap, leading to a relatively high density of quasiparticles at the junction and a short T1. Increasing the temperature gives the quasiparticles enough thermal energy to occupy the higher gap electrode, reducing the density at the junction and increasing T1. I present a model of this effect, extract the density of quasiparticles and the two superconducting energy gaps, and discuss implications for increasing the relaxation time of transmons. I also observed a similar phenomenon in low temperature microwave studies of titanium nitride coplanar waveguide resonators. I report on loss in a resonator at temperatures from 20 mK up to 1.1 K and with the application of infrared pair breaking radiation (λ=1.55 μm). With no applied IR light, the internal quality factor increased from QI = 800,000 at T < 70 mK up to QI=(2×10^6 ) at 600 mK. The resonant frequency f0 increased by 2 parts per million over the same temperature range. Above 600 mK both QI and f0 decreased rapidly, consistent with the increase in the density of thermally generated quasiparticles. With the application of IR light and for intensities below 1 aW μm^(-2) and T < 400 mK, QI increased in a similar way to increasing the temperature before beginning to decrease with larger intensities. I show that a model involving non-equilibrium quasiparticles and two regions of different superconducting gaps can explain this unexpected behavior.
Understanding the correlation between material properties and microwave losses in superconducting films is a crucial subject for developing low-loss materials for quantum circuits. We focus on vanadium (V) as a novel material for superconducting quantum devices and discuss loss in V films in relation to their structural properties. Using a sputtering method, we grow four V-film structures on (001)-oriented Si wafers, employing Nb and Ta as the buffer and capping layer materials, respectively: Nb/V/Ta, Nb/V, V/Ta, and V. X-ray diffraction and atomic force microscopy reveal that the V films grown on the Nb buffer layers have higher uniformity of lattice orientation and smaller grain size than that directly grown on the Si wafer. Coplanar waveguide resonators are fabricated from the four V-film structures, and averaged photon number (⟨nph⟩\langle n_{\rm ph} \rangle⟨nph​⟩) dependences of internal quality factor (QintQ_{\rm int}Qint​) are obtained by performing microwave measurements. By analyzing the obtained QintQ_{\rm int}Qint​ vs ⟨nph⟩\langle n_{\rm ph} \rangle⟨nph​⟩, it is found that loss at the V surface is dominated by ⟨nph⟩\langle n_{\rm ph} \rangle⟨nph​⟩-independent non-two-level-system (non-TLS) losses, which can be mitigated by introducing the Ta capping layer. Furthermore, the V films on the Nb buffer layers exhibit lower QintQ_{\rm int}Qint​ in the ⟨nph⟩\langle n_{\rm ph} \rangle⟨nph​⟩ range from 100^{0}0 to 106^{6}6 and higher non-TLS loss than that directly grown on Si wafers, even though the former has higher lattice-orientation uniformity than the latter. Origins of these trends might be relevant to V oxides, of which presence at surfaces and grain boundaries in bulk regions in the V resonators is suggested by energy dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy, and/or V hydrides.
Superconducting quantum devices have gained increasing interest over the past 15 years because of their role as promising candidates for implementing a large-scale quantum computer and as ultra-sensitive detectors. Superconducting resonators are one type of superconducting device which are used in a variety of applications including quantum computing and radioastronomy. They can achieve large quality factors which are important for these applications and a variety of others. Specific examples of these applications include the readout and coupling of superconducting qubits and also microwave kinetic inductance detector arrays for sub-mm wavelength astronomical measurements. High quality factors also enable the study of very subtle features in the electromagnetic response of the resonator. This feature in turn offers provides a method to characterize loss mechanisms which affect the performance of superconducting qubits, by measuring the quality factor of a resonator. Dielectric loss is an example of such a loss mechanism, and is considered to be one of, if not \\it the \\rm major obstacle to overcome in order to construct scalable quantum technologies based on superconducting devices. This type of loss arises from the coupling of the electric field in the device to spurious degrees of freedom which arise naturally the dielectric environment of the device. The fast-growing interest in the physics and applications of superconducting resonators has renewed interest in an improving our fundamental understanding of dielectric loss. This interest involves the study of a much bigger and older question in condensed matter physics; namely, what is the microscopic physics which governs the behaviour and of an amorphous material at low-temperatures? \n \nIn this thesis, we present a systematic study of dielectric loss in amorphous aluminum oxide using superconducting microwave resonators. Measurements of the intrinsic loss tangent over a large temperature range of 40~mK to 1~K are presented and analyzed in detail. Some aspects of the data are well understood in terms of the standard tunnelling two-level system model, while others require a deeper analysis of the electrodynamics of the resonator and insights from more advanced theories. We employ a consistent approach using numerical simulations of the resonator to understand loss mechanisms arising from both an inhomogeneous electric field and multiple dielectric layers. We measure saturation effects which provide insight into coherent properties of two-level system ensembles and the mutual interaction between them. Excellent agreement with the two-level system model is found for intrinsic losses, however the strong dependence on temperature which we observe for saturation effects is not predicted in the standard form of the model. We find that this dependence can be understood in terms of the theory of spectral diffusion which is consistent with a strong mutual interaction between two-level systems contributes to broadening of their spectral linewidths.