Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Conference on Lasers and Electro-Optics

Electromagnetically induced transparency in rubidium-filled kagome HC-PCF

Benabid, Maric, Andre Nicholas Luiten, Couny

Published Jan 1, 2008• 1 citation
OpenAlex

Related papers

Electromagnetically Induced Transparency inRubidium-Filled HC-PCF

P. S. Light, Andre Nicholas Luiten

•Jan 1, 2006•0 citations

Electromagnetically Induced Transparency in Rubidium-Filled HC-PCF

P. S. Light, Fetah Benabid, M. Marić +2 more

This paper report the observation of electromagnetically induced transparency (EIT) in Rb-filled HC-PCF. We observe EIT in a lambda energy-level configuration with narrow linewidth, in contrast to that obtained by Ghosh et al. (2006). The fibre used in this experiment is large-pitch kagome-structured HC-PCF (Couny et al., 2006), with a core diameter of 11 mum. In order to prevent rubidium from being quickly adsorbed onto the silica walls, the fibre core was coated with PDMS by first filling it with a solution of 2% PDMS in diethyl-ether, and then evaporating the ether. The PDMS wall coating has a strongly beneficial effect in suppressing these dephasing collisions but further measurements at much lower coupling intensities are necessary to quantify how small the dephasing due to the coated wall is.

Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe-EQEC)•Jun 1, 2007•2 citations

Electromagnetically induced transparency schemes within rubidium vapor

Sara Shepherd, David J. Fulton, Richard R. Moseley +2 more

Quantum Electronics and Laser Science Conference•May 22, 1995•0 citations

Progress towards atomic vapor photonic microcells: Coherence and polarization relaxation measurements in coated and uncoated HC-PCF

Thomas D. Bradley, John J. McFerran, Jenny Jouin +3 more

We report a comparative study on dephasing mechanisms between inner core coated and uncoated sections of the same Kagome hypocycloid-shaped core hollow core photonic crystal fibers (HC-PCF) filled with rubidium vapor. The comparison is performed by measuring the atomic polarization relaxation and electromagnetically induced transparency (EIT) linewidth in Rb loaded polydimethylsiloxane (PDMS) inner wall coated and bare silica core Kagome HC-PCF. The measurements show a polarization relaxation time of 32μs in a PDMS coated Kagome HC-PCF and 24μs in uncoated Kagome HC-PCF. A minimum EIT linewidth of 6.2±0.8MHz is achieved in PDMS coated Kagome HC-PCF, and 8.3±0.9 MHz for the uncoated Kagome HC-PCF.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Mar 6, 2013•2 citations

Molecular and atomic confinement in large core photonic microcells for slow light and laser metrology applications

Natalie V. Wheeler

This thesis describes developments in the fabrication and applications of photonic microcells (PMCs). A PMC is a length of gas-filled hollow core-photonic crystal fibre (HC-PCF) that is hermetically sealed by splicing both ends to standard single mode fibre. A PMC enables integration of gas-filled HC-PCF into all-fibre systems with low insertion loss. PMCs have applications in coherent optics and metrology, where specific HC-PCF designs are advantageous. Two types of state-of-the-art HC-PCF, double bandgap HCPCF and large-pitch Kagome fibre, are fabricated. The double bandgap HC-PCF extends the usable bandwidth of the fibre by providing low loss guidance across two transmission bands. The large-pitch Kagome HC-PCF has a record low attenuation of 0.3 dB/m at 800 nm, while maintaining broadband guidance, which is partially attributed to the core shape. Three distinct developments in the field of PMCs are described. Firstly, a record length 20 metre acetylene-filled PMC is fabricated which is the key component in the first demonstration of an all-fibre slow and fast light system based on electromagnetically induced transparency. Secondly, a technique based on fibre tapering is presented which enables low loss integration of large core Kagome HC-PCFs into PMC form. Thirdly, micromirrors are developed and integrated with HC-PCF to confine light in the longitudinal dimension, providing a means to fabricate multi-pass PMCs. Two uncoated micromirrors are used to form a low finesse microcavity in Kagome HC-PCF, with record high fringe visibility using reflections from a silica/air junction. In collaboration with Kansas State University, an acetylene optical reference with sub-10 KHz accuracy and the first acetylene laser based on population inversion are demonstrated using Kagome HC-PCF.Finally, this thesis reports on rubidium vapour loading in HC-PCF with the ultimate aim being the production of a rubidium-filled PMC for applications in metrology. Preliminary results highlight the limited loading distance of the current technique and modified loading schemes are outlined accordingly.

•Nov 1, 2010•0 citations

Electromagnetically induced transparency in rubidium: An advanced undergraduate laboratory

Shannon K. Mayer, Abraham J. Olson

Bulletin of the American Physical Society•May 16, 2008•1 citation
This paper report the observation of electromagnetically induced transparency (EIT) in Rb-filled HC-PCF. We observe EIT in a lambda energy-level configuration with narrow linewidth, in contrast to that obtained by Ghosh et al. (2006). The fibre used in this experiment is large-pitch kagome-structured HC-PCF (Couny et al., 2006), with a core diameter of 11 mum. In order to prevent rubidium from being quickly adsorbed onto the silica walls, the fibre core was coated with PDMS by first filling it with a solution of 2% PDMS in diethyl-ether, and then evaporating the ether. The PDMS wall coating has a strongly beneficial effect in suppressing these dephasing collisions but further measurements at much lower coupling intensities are necessary to quantify how small the dephasing due to the coated wall is.
We report a comparative study on dephasing mechanisms between inner core coated and uncoated sections of the same Kagome hypocycloid-shaped core hollow core photonic crystal fibers (HC-PCF) filled with rubidium vapor. The comparison is performed by measuring the atomic polarization relaxation and electromagnetically induced transparency (EIT) linewidth in Rb loaded polydimethylsiloxane (PDMS) inner wall coated and bare silica core Kagome HC-PCF. The measurements show a polarization relaxation time of 32μs in a PDMS coated Kagome HC-PCF and 24μs in uncoated Kagome HC-PCF. A minimum EIT linewidth of 6.2±0.8MHz is achieved in PDMS coated Kagome HC-PCF, and 8.3±0.9 MHz for the uncoated Kagome HC-PCF.
This thesis describes developments in the fabrication and applications of photonic microcells (PMCs). A PMC is a length of gas-filled hollow core-photonic crystal fibre (HC-PCF) that is hermetically sealed by splicing both ends to standard single mode fibre. A PMC enables integration of gas-filled HC-PCF into all-fibre systems with low insertion loss. PMCs have applications in coherent optics and metrology, where specific HC-PCF designs are advantageous. Two types of state-of-the-art HC-PCF, double bandgap HCPCF and large-pitch Kagome fibre, are fabricated. The double bandgap HC-PCF extends the usable bandwidth of the fibre by providing low loss guidance across two transmission bands. The large-pitch Kagome HC-PCF has a record low attenuation of 0.3 dB/m at 800 nm, while maintaining broadband guidance, which is partially attributed to the core shape. Three distinct developments in the field of PMCs are described. Firstly, a record length 20 metre acetylene-filled PMC is fabricated which is the key component in the first demonstration of an all-fibre slow and fast light system based on electromagnetically induced transparency. Secondly, a technique based on fibre tapering is presented which enables low loss integration of large core Kagome HC-PCFs into PMC form. Thirdly, micromirrors are developed and integrated with HC-PCF to confine light in the longitudinal dimension, providing a means to fabricate multi-pass PMCs. Two uncoated micromirrors are used to form a low finesse microcavity in Kagome HC-PCF, with record high fringe visibility using reflections from a silica/air junction. In collaboration with Kansas State University, an acetylene optical reference with sub-10 KHz accuracy and the first acetylene laser based on population inversion are demonstrated using Kagome HC-PCF.Finally, this thesis reports on rubidium vapour loading in HC-PCF with the ultimate aim being the production of a rubidium-filled PMC for applications in metrology. Preliminary results highlight the limited loading distance of the current technique and modified loading schemes are outlined accordingly.