Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Superconductor Science and Technology

Cryogenic readout of superconducting nanowire single-photon detectors using high-sensitivity adiabatic quantum-flux-parametron circuits

Fumihiro China, Naoki Takeuchi, Shigehito Miki, Masahiro Yabuno, Shigeyuki Miyajima, Hirotaka Terai

Published Feb 18, 2021• 7 citations
Publisher

Abstract

Abstract We have been developing readout interfaces for superconducting nanowire single-photon detectors (SSPDs) using adiabatic quantum-flux-parametron (AQFP) logic. AQFP circuits operate with low power consumption, low bias currents, and high sensitivity, and thus are suitable as readout interfaces for large SSPD arrays. In this study, we develop a high-sensitivity AQFP interface, consisting of a current transformer, comparator, and rising-edge detector. We systematically investigated the current sensitivity of the AQFP interface by operating an NbTiN SSPD with the interface in a 0.1 W Gifford–McMahon cryocooler. We compared the outputs from the AQFP interface with the direct outputs from the SSPD, thereby demonstrating a sensitivity of 3.5 μ A, which is much smaller than that of the single-flux-quantum interfaces that we developed before.

DOI
10.1088/1361-6668/abe7ac

Related papers

Adiabatic quantum-flux-parametron interface for the readout of superconducting nanowire single-photon detectors

Naoki Takeuchi, Taro Yamashita, Shigeyuki Miyajima +3 more

We propose and demonstrate a low-power and low-current cryogenic readout interface for a superconducting nanowire single-photon detector (SSPD) using adiabatic quantum-flux-parametron (AQFP) logic. The AQFP readout interface samples and digitizes the current signal from an SSPD, generating binary output data in accordance with the detection behavior of the SSPD. We demonstrate the correct operation of an SSPD with the interface, where the AQFP readout interface and the SSPD are placed in separate 0.1-W Gifford–McMahon (GM) cryocoolers and are interconnected via coaxial cables. It was found that the temperature of the sample stage did not change even after the AQFP readout interface was turned on, which revealed that the AQFP readout interface uses sufficiently low power and current for a compact cryocooler.

Optics Express•Dec 15, 2017•21 citations

Demonstration of a Superconducting Nanowire Single-Photon Detector using Adiabatic Quantum-Flux-Parametron Logic in a 0.1-W Gifford-McMahon Cryocooler

Naoki Takeuchi, Taro Yamashita, Shigeyuki Miyajima +3 more

Superconducting nanowire single-photon detectors (SSPDs or SNSPDs) have superior performance and are thus used for many applications, such as quantum information and laser communications. Lately, much effort has been spent on the development of multi-pixel SSPD arrays to achieve single-photon-level imaging. SSPD arrays require efficient readout schemes that reduce the number of coaxial cables for reading out the SSPD pixels. In a previous study, we proposed a readout interface using adiabatic quantum-flux-parametron (AQFP) logic, which digitizes the information of an SSPD at cryogenic temperature. In this study, we show the first demonstration of an SSPD that is read out by the AQFP readout interface placed in the same 0.1-W Gifford-McMahon cryocooler. The measurement results show that the AQFP readout interface reads out the SSPD with low error rates. Also, it is found that the temperature of the sample stage does not change even after the AQFP readout interface is turned on, which indicates that the power and current required for the AQFP readout interface are sufficiently low for the implementation using a compact cryocooler.

IEEE Transactions on Applied Superconductivity•Mar 18, 2019•5 citations

An Adiabatic Superconductor Comparator With 46 nA Sensitivity

Naoki Takeuchi, Taiki Yamae, Hideo Suzuki +1 more

Adiabatic quantum-flux-parametron (AQFP) circuits can operate with extremely small energy dissipation (∼1 zJ per junction at 5 GHz) and high sensitivity (∼1 μA) owing to adiabatic switching. Thus, AQFP logic is suitable to use as readout interfaces for cryogenic detectors, such as superconducting nanowire single-photon detectors (SSPDs). In order to extend the application of AQFP logic to various detectors, it is crucial to achieve even better sensitivity because some detectors, such as WSi SSPDs and transition edge sensors (TESs), require sub-μA sensitivity. In the present study, we propose a high-sensitivity AQFP comparator with a current transformer (CT), which increases the equivalent input current and thereby improves the sensitivity. Numerical simulation shows that the proposed comparator achieves a sensitivity approximately six times better than that of a conventional AQFP comparator. Furthermore, we demonstrate a sensitivity of 46 nA at 4.2 K for a sampling frequency of 500 Hz in the experiment.

arXiv:2010.13584•IEEE Transactions on Applied Superconductivity•Feb 24, 2021•8 citations

Scalable readout interface for superconducting nanowire single-photon detectors using AQFP and RSFQ logic families

Naoki Takeuchi, Fumihiro China, Shigehito Miki +4 more

We propose a scalable readout interface for superconducting nanowire single-photon detector (SSPD) arrays, which we call the AQFP/RSFQ interface. This interface is composed of adiabatic quantum-flux-parametron (AQFP) and rapid single-flux-quantum (RSFQ) logic families. The AQFP part reads out the spatial information of an SSPD array via a single cable, and the RSFQ part reads out the temporal information via a single cable. The hybrid interface has high temporal resolution owing to low timing jitter in the operation of the RSFQ part. In addition, the hybrid interface achieves high circuit scalability because of low supply current in the operation of the AQFP part. Therefore, the hybrid interface is suitable for handling many-pixel SSPD arrays. We demonstrate a four-pixel SSPD array using the hybrid interface as proof of concept. The measurement results show that the hybrid interface can read out all of the pixels with a low error rate and low timing jitter.

arXiv:2004.01380•Optics Express•May 1, 2020•24 citations

Readout Electronics Using Single-Flux-Quantum Circuit Technology for Superconducting Single-Photon Detector Array

Hirotaka Terai, Shigehito Miki, Zhen Wang

Superconducting single-photon detectors (SSPDs) based on NbN nanowires possess properties such as high counting rate, low dark count rate and small timing jitter, which are promising characteristics for a quantum key distribution system. An SSPD array has recently attracted attention, because it can provide a higher counting rate, and spatial and photon-number resolutions. We propose readout electronics using single-flux-quantum (SFQ) circuits to process a large number of output signals from an SSPD array. We designed and tested an interface circuit between an SSPD and SFQ circuit, and successfully observed SFQ pulse generation for an input pulse with a current amplitude of 17.4 ~ 36.4 muA , which is comparable with an output current amplitude of the SSPD. The interface circuit was also operational for an input pulse duration of 1.6 ns, which is shorter than the typical recovery time of the SSPD.

IEEE Transactions on Applied Superconductivity•Jun 1, 2009•63 citations

Technologies for superconducting nanowire single-photon detector array system

Shigehito Miki, Taro Yamashita, Hirotaka Terai +2 more

We present the development of key technologies for realization of superconducting nanowire single photon detector array system, which enables high counting rates, and allow spatial and pseudo photon number resolution. Toward the realization of practical large-scale SSPD array system, primary issue is how to avoid heat flow into cryocooler system. One of the challenging tasks is the development of their readout electronics. In the conventional readout technique used for single pixel devices, the number of high-frequency coaxial cables increases proportionally with the number of arrays. This causes a significant increase in the heat load from room temperature, which makes the implementation of the SSPD arrays in a compact refrigerator difficult. To overcome this problem, we proposed applying readout electronics with superconducting single-flux-quantum (SFQ) logic circuitsWe show the implementation and successful operation of four pixels SSPD array connected to SFQ readout electronics with parallel bias scheme in a 0.1W GM cryocooler system.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jun 3, 2013•1 citation
Abstract We have been developing readout interfaces for superconducting nanowire single-photon detectors (SSPDs) using adiabatic quantum-flux-parametron (AQFP) logic. AQFP circuits operate with low power consumption, low bias currents, and high sensitivity, and thus are suitable as readout interfaces for large SSPD arrays. In this study, we develop a high-sensitivity AQFP interface, consisting of a current transformer, comparator, and rising-edge detector. We systematically investigated the current sensitivity of the AQFP interface by operating an NbTiN SSPD with the interface in a 0.1 W Gifford–McMahon cryocooler. We compared the outputs from the AQFP interface with the direct outputs from the SSPD, thereby demonstrating a sensitivity of 3.5 μ A, which is much smaller than that of the single-flux-quantum interfaces that we developed before.
We propose and demonstrate a low-power and low-current cryogenic readout interface for a superconducting nanowire single-photon detector (SSPD) using adiabatic quantum-flux-parametron (AQFP) logic. The AQFP readout interface samples and digitizes the current signal from an SSPD, generating binary output data in accordance with the detection behavior of the SSPD. We demonstrate the correct operation of an SSPD with the interface, where the AQFP readout interface and the SSPD are placed in separate 0.1-W Gifford–McMahon (GM) cryocoolers and are interconnected via coaxial cables. It was found that the temperature of the sample stage did not change even after the AQFP readout interface was turned on, which revealed that the AQFP readout interface uses sufficiently low power and current for a compact cryocooler.
Superconducting nanowire single-photon detectors (SSPDs or SNSPDs) have superior performance and are thus used for many applications, such as quantum information and laser communications. Lately, much effort has been spent on the development of multi-pixel SSPD arrays to achieve single-photon-level imaging. SSPD arrays require efficient readout schemes that reduce the number of coaxial cables for reading out the SSPD pixels. In a previous study, we proposed a readout interface using adiabatic quantum-flux-parametron (AQFP) logic, which digitizes the information of an SSPD at cryogenic temperature. In this study, we show the first demonstration of an SSPD that is read out by the AQFP readout interface placed in the same 0.1-W Gifford-McMahon cryocooler. The measurement results show that the AQFP readout interface reads out the SSPD with low error rates. Also, it is found that the temperature of the sample stage does not change even after the AQFP readout interface is turned on, which indicates that the power and current required for the AQFP readout interface are sufficiently low for the implementation using a compact cryocooler.
Adiabatic quantum-flux-parametron (AQFP) circuits can operate with extremely small energy dissipation (∼1 zJ per junction at 5 GHz) and high sensitivity (∼1 μA) owing to adiabatic switching. Thus, AQFP logic is suitable to use as readout interfaces for cryogenic detectors, such as superconducting nanowire single-photon detectors (SSPDs). In order to extend the application of AQFP logic to various detectors, it is crucial to achieve even better sensitivity because some detectors, such as WSi SSPDs and transition edge sensors (TESs), require sub-μA sensitivity. In the present study, we propose a high-sensitivity AQFP comparator with a current transformer (CT), which increases the equivalent input current and thereby improves the sensitivity. Numerical simulation shows that the proposed comparator achieves a sensitivity approximately six times better than that of a conventional AQFP comparator. Furthermore, we demonstrate a sensitivity of 46 nA at 4.2 K for a sampling frequency of 500 Hz in the experiment.
We propose a scalable readout interface for superconducting nanowire single-photon detector (SSPD) arrays, which we call the AQFP/RSFQ interface. This interface is composed of adiabatic quantum-flux-parametron (AQFP) and rapid single-flux-quantum (RSFQ) logic families. The AQFP part reads out the spatial information of an SSPD array via a single cable, and the RSFQ part reads out the temporal information via a single cable. The hybrid interface has high temporal resolution owing to low timing jitter in the operation of the RSFQ part. In addition, the hybrid interface achieves high circuit scalability because of low supply current in the operation of the AQFP part. Therefore, the hybrid interface is suitable for handling many-pixel SSPD arrays. We demonstrate a four-pixel SSPD array using the hybrid interface as proof of concept. The measurement results show that the hybrid interface can read out all of the pixels with a low error rate and low timing jitter.
Superconducting single-photon detectors (SSPDs) based on NbN nanowires possess properties such as high counting rate, low dark count rate and small timing jitter, which are promising characteristics for a quantum key distribution system. An SSPD array has recently attracted attention, because it can provide a higher counting rate, and spatial and photon-number resolutions. We propose readout electronics using single-flux-quantum (SFQ) circuits to process a large number of output signals from an SSPD array. We designed and tested an interface circuit between an SSPD and SFQ circuit, and successfully observed SFQ pulse generation for an input pulse with a current amplitude of 17.4 ~ 36.4 muA , which is comparable with an output current amplitude of the SSPD. The interface circuit was also operational for an input pulse duration of 1.6 ns, which is shorter than the typical recovery time of the SSPD.
We present the development of key technologies for realization of superconducting nanowire single photon detector array system, which enables high counting rates, and allow spatial and pseudo photon number resolution. Toward the realization of practical large-scale SSPD array system, primary issue is how to avoid heat flow into cryocooler system. One of the challenging tasks is the development of their readout electronics. In the conventional readout technique used for single pixel devices, the number of high-frequency coaxial cables increases proportionally with the number of arrays. This causes a significant increase in the heat load from room temperature, which makes the implementation of the SSPD arrays in a compact refrigerator difficult. To overcome this problem, we proposed applying readout electronics with superconducting single-flux-quantum (SFQ) logic circuitsWe show the implementation and successful operation of four pixels SSPD array connected to SFQ readout electronics with parallel bias scheme in a 0.1W GM cryocooler system.