Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

OSA Quantum 2.0 Conference

Control and readout of a superconducting qubit using a cryogenic photonic link

Florent Lecocq, José Aumentado, Scott A. Diddams, Franklyn Quinlan, John D. Teufel

Published Jan 1, 2020• 2 citations
Publisher

Abstract

We perform the control and readout of a superconducting qubit using microwave signals generated by a high-speed photodiode operating a 20mK. We demonstrate fast single-qubit gates and high-fidelity single-shot readout while maintaining high qubit coherence.
DOI
10.1364/quantum.2020.qm6a.3

Related papers

High-Fidelity Cryogenic Photonic Link for the Readout of Superconducting Qubits

Franklyn Quinlan, Scott A. Diddams, Florent Lecocq +2 more

We perform readout of a superconducting qubit with microwave pulses delivered via optical fiber and a cryogenic high-speed photodetector. High coherence and readout fidelity are maintained, compatible with the stringent requirements of quantum information systems.

Conference on Lasers and Electro-Optics•Jan 1, 2020•1 citation

All-optical superconducting qubit readout

Georg Arnold, Thomas Werner, Rishabh Sahu +3 more

The rapid development of superconducting quantum hardware is expected to run into substantial restrictions on scalability because error correction in a cryogenic environment has stringent input-output requirements. Classical data centres rely on fibre-optic interconnects to remove similar networking bottlenecks. In the same spirit, ultracold electro-optic links have been proposed and used to generate qubit control signals, or to replace cryogenic readout electronics. So far, these approaches have suffered from either low efficiency, low bandwidth or additional noise. Here we realize radio-over-fibre qubit readout at millikelvin temperatures. We use one device to simultaneously perform upconversion and downconversion between microwave and optical frequencies and so do not require any active or passive cryogenic microwave equipment. We demonstrate all-optical single-shot readout in a circulator-free readout scheme. Importantly, we do not observe any direct radiation impact on the qubit state, despite the absence of shielding elements. This compatibility between superconducting circuits and telecom-wavelength light is not only a prerequisite to establish modular quantum networks, but it is also relevant for multiplexed readout of superconducting photon detectors and classical superconducting logic.

arXiv:2310.16817•Nature Physics•Feb 11, 2025•48 citations

Fast Microwave-free State Preparation and Measurement of Superconducting Qubits

R. Abraham, F. Amet, P. Anderson +212 more

Fast, high-fidelity, scalable state preparation and measurement is critical to the realization of a quantum computing system. The state-of-the-art methods for preparation and readout of superconducting qubits require finely tuned microwave signals and ~100 ns of measurement time, which are major obstacles to the scalability and performance of superconducting quantum computers. Here, we have demonstrated novel, microwave-free methods for both preparation and readout of superconducting qubits with >99% fidelity in only 10 ns for either operation while maintaining qubit coherence. This technology is compatible with scalable superconducting digital control systems, and using quantum flux parametrons for amplification, we demonstrated full quantum-to-digital conversion in only 15 ns, which is an order of magnitude faster than state-of-the-art microwave-based techniques.

quant-pharXiv:2609.01334•Sep 2, 2026•0 citations

Digital Readout and Control of a Superconducting Qubit

Caleb Howington

In the quest to build a fault-tolerant quantum computer, superconducting circuits based on Josephson junctions have emerged as a leading architecture. Coherence times have increased significantly over the last two decades, and processors with ∼ 50 qubits have been experimentally demonstrated. These systems traditionally utilize microwave frequency control signals, and heterodyne based detection schemes for measurement. Both of these techniques rely heavily on room temperature microwave generators, high-bandwidth lines from room temperature to millikelvin temperatures, and bulky non-reciprocal elements such as cryogenic microwave isolators. Reliance on these elements makes it impractical to scale existing devices up a single order of magnitude, let alone the 5-6 orders of magnitude needed for performing fault-tolerant quantum algorithms. Here, I present results that suggesting superconducting digital logic, namely Single Flux Quantum (SFQ) logic, can replace analog control and measurement techniques, avoiding the significant overhead involved. I describe a scheme for measuring qubits with a device known as a Josephson Photomultiplier (JPM), which crucially stores the result of a qubit measurement in a classical circulating supercurrent within the device and allows for integration with SFQ detection circuitry. This technique is experimentally demonstrated, with single-shot measurement fidelity of 92%. Two methods for accessing this measurement result are presented, one utilizing ballistic fluxons, and another utilizing flux comparison. Initial experimental results of the latter are presented. In addition, I describe a scheme for controlling qubits with sequences of digital SFQ pulses. This method is then used to control a qubit without a microwave signal generator, with results of an average single-qubit gate fidelity of around 95%. When combined, these techniques form a nearly fully digital interface to superconducting qubits, which could allow these systems to scale much more easily.

•Jan 1, 2019•0 citations

Cryogenic photonic link using an extended-InGaAs photodiode and short pulse illumination toward high-fidelity drive of superconducting qubits

Takuma Nakamura, Dahyeon Lee, Jason Horng +3 more

We investigate short pulse illumination of a high-speed extended-InGaAs photodiode at cryogenic temperatures toward its use in control and readout of superconducting qubits. First, we demonstrate high detector responsivity at 1550 nm illumination at 20 mK, a wavelength band unavailable to cryogenic standard InGaAs detectors due to the temperature-dependent bandgap shift. Second, we demonstrate an improved signal-to-noise ratio (SNR) at the shot noise limit for cryogenic short optical pulse detection when compared with conventional modulated continuous-wave laser detection. At 40 μA of photocurrent and a detector temperature of 4 K, short pulse detection yields an SNR improvement of 20 dB and 3 dB for phase and amplitude quadratures, respectively. Last, we discuss how short pulse detection offers a path for signal multiplexing, with a demonstration of simultaneous production of microwave pulses at two different carrier frequencies. Together, these advancements establish a path toward low noise and power efficient multiplexed photonic links for quantum computing with a large number of superconducting qubits.

arXiv:2501.00545•Optica Quantum•May 2, 2025•7 citations

All-optical control and multiplexed readout of multiple superconducting qubits

Xiaoxuan Pan, Chuanlong Ma, Jia-Qi Wang +12 more

Superconducting quantum circuits operate at millikelvin temperatures, typically requiring independent microwave cables for each qubit for connecting room-temperature control and readout electronics. However, scaling to large-scale processors hosting hundreds of qubits faces a severe input/output (I/O) bottleneck, as the dense cable arrays impose prohibitive constraints on physical footprint, thermal load, wiring complexity, and cost. Here we demonstrate a complete optical I/O architecture for superconducting quantum circuits, in which all control and readout signals are transmitted exclusively via optical photons. Employing a broadband traveling-wave Brillouin microwave-to-optical transducer, we achieve simultaneous frequency-multiplexed optical readout of two qubits. Combined with fiber-integrated photodiode arrays for control signal delivery, this closed-loop optical I/O introduces no measurable degradation to qubit coherence times, with an optically driven single-qubit gate fidelity showing only a 0.19% reduction relative to standard microwave operation. These results establish optical interconnects as a viable path toward large-scale superconducting quantum processors, and open the possibility of networking multiple superconducting quantum computers housed in separate dilution refrigerators through a centralized room-temperature control infrastructure.

quant-pharXiv:2512.21199•Dec 25, 2025•4 citations
The rapid development of superconducting quantum hardware is expected to run into substantial restrictions on scalability because error correction in a cryogenic environment has stringent input-output requirements. Classical data centres rely on fibre-optic interconnects to remove similar networking bottlenecks. In the same spirit, ultracold electro-optic links have been proposed and used to generate qubit control signals, or to replace cryogenic readout electronics. So far, these approaches have suffered from either low efficiency, low bandwidth or additional noise. Here we realize radio-over-fibre qubit readout at millikelvin temperatures. We use one device to simultaneously perform upconversion and downconversion between microwave and optical frequencies and so do not require any active or passive cryogenic microwave equipment. We demonstrate all-optical single-shot readout in a circulator-free readout scheme. Importantly, we do not observe any direct radiation impact on the qubit state, despite the absence of shielding elements. This compatibility between superconducting circuits and telecom-wavelength light is not only a prerequisite to establish modular quantum networks, but it is also relevant for multiplexed readout of superconducting photon detectors and classical superconducting logic.
Fast, high-fidelity, scalable state preparation and measurement is critical to the realization of a quantum computing system. The state-of-the-art methods for preparation and readout of superconducting qubits require finely tuned microwave signals and ~100 ns of measurement time, which are major obstacles to the scalability and performance of superconducting quantum computers. Here, we have demonstrated novel, microwave-free methods for both preparation and readout of superconducting qubits with >99% fidelity in only 10 ns for either operation while maintaining qubit coherence. This technology is compatible with scalable superconducting digital control systems, and using quantum flux parametrons for amplification, we demonstrated full quantum-to-digital conversion in only 15 ns, which is an order of magnitude faster than state-of-the-art microwave-based techniques.
In the quest to build a fault-tolerant quantum computer, superconducting circuits based on Josephson junctions have emerged as a leading architecture. Coherence times have increased significantly over the last two decades, and processors with ∼ 50 qubits have been experimentally demonstrated. These systems traditionally utilize microwave frequency control signals, and heterodyne based detection schemes for measurement. Both of these techniques rely heavily on room temperature microwave generators, high-bandwidth lines from room temperature to millikelvin temperatures, and bulky non-reciprocal elements such as cryogenic microwave isolators. Reliance on these elements makes it impractical to scale existing devices up a single order of magnitude, let alone the 5-6 orders of magnitude needed for performing fault-tolerant quantum algorithms. Here, I present results that suggesting superconducting digital logic, namely Single Flux Quantum (SFQ) logic, can replace analog control and measurement techniques, avoiding the significant overhead involved. I describe a scheme for measuring qubits with a device known as a Josephson Photomultiplier (JPM), which crucially stores the result of a qubit measurement in a classical circulating supercurrent within the device and allows for integration with SFQ detection circuitry. This technique is experimentally demonstrated, with single-shot measurement fidelity of 92%. Two methods for accessing this measurement result are presented, one utilizing ballistic fluxons, and another utilizing flux comparison. Initial experimental results of the latter are presented. In addition, I describe a scheme for controlling qubits with sequences of digital SFQ pulses. This method is then used to control a qubit without a microwave signal generator, with results of an average single-qubit gate fidelity of around 95%. When combined, these techniques form a nearly fully digital interface to superconducting qubits, which could allow these systems to scale much more easily.
We investigate short pulse illumination of a high-speed extended-InGaAs photodiode at cryogenic temperatures toward its use in control and readout of superconducting qubits. First, we demonstrate high detector responsivity at 1550 nm illumination at 20 mK, a wavelength band unavailable to cryogenic standard InGaAs detectors due to the temperature-dependent bandgap shift. Second, we demonstrate an improved signal-to-noise ratio (SNR) at the shot noise limit for cryogenic short optical pulse detection when compared with conventional modulated continuous-wave laser detection. At 40 μA of photocurrent and a detector temperature of 4 K, short pulse detection yields an SNR improvement of 20 dB and 3 dB for phase and amplitude quadratures, respectively. Last, we discuss how short pulse detection offers a path for signal multiplexing, with a demonstration of simultaneous production of microwave pulses at two different carrier frequencies. Together, these advancements establish a path toward low noise and power efficient multiplexed photonic links for quantum computing with a large number of superconducting qubits.
Superconducting quantum circuits operate at millikelvin temperatures, typically requiring independent microwave cables for each qubit for connecting room-temperature control and readout electronics. However, scaling to large-scale processors hosting hundreds of qubits faces a severe input/output (I/O) bottleneck, as the dense cable arrays impose prohibitive constraints on physical footprint, thermal load, wiring complexity, and cost. Here we demonstrate a complete optical I/O architecture for superconducting quantum circuits, in which all control and readout signals are transmitted exclusively via optical photons. Employing a broadband traveling-wave Brillouin microwave-to-optical transducer, we achieve simultaneous frequency-multiplexed optical readout of two qubits. Combined with fiber-integrated photodiode arrays for control signal delivery, this closed-loop optical I/O introduces no measurable degradation to qubit coherence times, with an optically driven single-qubit gate fidelity showing only a 0.19% reduction relative to standard microwave operation. These results establish optical interconnects as a viable path toward large-scale superconducting quantum processors, and open the possibility of networking multiple superconducting quantum computers housed in separate dilution refrigerators through a centralized room-temperature control infrastructure.