Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Optical spin-polarisation in a triplet state in irradiated and annealed type 1b diamonds

J.H.N. Loubser, J.A. Van Wyk

Published Jan 1, 1977• 21 citations
OpenAlex

Abstract

A triplet ESR spectrum with trigonal symmetry with high field lines in emission has been observed in electron or neutron irradiated Type Ib diamonds after annealing. The spectrum is only observed on illumination with light near 6000 A.

Related papers

Optically detected spin coherence of the diamond N-V centre in its triplet ground state

Eric van Oort, Neil B. Manson, Max Glasbeek

For the N-V centre in type Ib diamond the optical detection of spin coherence in the 3 A state is reported. The 3 A-state lifetime is studied as a function of the light intensity used for the optical excitation of the N-V centre by means of spin-locking experiments. The shortening of the lifetime at higher excitation intensities provides evidence for the previously proposed idea that the 3 A state of the N-V centre is the ground state.

Journal of Physics C Solid State Physics•Aug 20, 1988•204 citations

Optically induced spin orientation of the nitrogen-vacancy center in diamond

Neil Manson, John P. D. Martin

Optical illumination of the N-V color center in diamond gives selective population of the ground electron spin levels and by working close to an avoided crossing polarization of the nuclear hyperfine levels is also obtained.

Optical Fiber Communication Conference•Jan 1, 2001•0 citations

Optical and magnetic resonance studies of point defects in CVD diamond

Ulrika F. S. D’Haenens-Johansson

This thesis reports research conducted on point defects in single crystal diamond utilising the complementary techniques of electron paramagnetic resonance (EPR), optical absorption and photoluminescence (PL) spectroscopy. Intentional silicon-doping of chemical vapour deposition (CVD) diamond allowed the production of samples grown on differently oriented substrates and containing distinct silicon isotopic abundances. The EPR spectrum of the neutral charge state of the silicon split-vacancy centre in diamond, (Si-V)0, has been characterised in the literature. Evidence for the assignment of the 1.31 eV zero phonon line (ZPL) seen in absorption and PL to the 3A2g -> 3A1u transition arising at (Si-V)0 is presented. Reversible charge transfer between the negatively charged centre, (Si-V)− (ZPL at 1.68 eV), and (Si-V)0 enabled the determination of calibration factors relating defect concentrations to their respective ZPL intensities. Preferential alignment of trigonal centres, such as (Si-V), in CVD material grown on {110}-substrates has been observed. The formation of (Si-V) centres during CVD synthesis and via irradiation and annealing of silicon-doped diamond was studied. Variable temperature EPR spectroscopy under illumination was used to investigate the optical spin polarisation (SP) of the (Si-V)0 3A2g ground state. Two different mechanisms for the SP are considered; selective intersystem crossing of (Si-V)0, and photoionisation of (Si-V)−. The properties of (Si-V)0 are compared to those of the extensively studied negatively charged nitrogen vacancy centre, (N-V)−. The effective spin-lattice relaxation and spin polarisation rates for both centres during continuous illumination are explored using pulsed EPR methods. A new defect, labelledWAR3, with spin S = 1 2 was observed in silicon-doped diamond and characterised using multifrequency EPR. Analysis of the data revealed that WAR3 is the neutral charge state of a silicon divacancy complex decorated by a hydrogen atom, (Si-V2:H)0. The experimentally derived 29Si and 1H hyperfine parameters are in good agreement with the values calculated using the spindensity- functional technique, confirming this model and ruling out a non-planar structure.

•Sep 11, 2026•0 citations

Optical spin polarization in the di-〈001〉-split interstitial (R1) centre in diamond

Daniel J. Twitchen, Mark E. Newton, J M Baker +2 more

Diamond and Related Materials•Jun 1, 1999•6 citations

Elmas içerisinde renk merkezleri oluşturularak kuantum emiterlerin üretilmesi

Şentürk Irmak, Sevil Berrak

This thesis explores the generation of nitrogen-vacancy (NV) color centers in diamond, which are solid-state quantum emitters. Quantum emitters are critical for applications in quantum cryptography, sensing, and computing. Due to their stable photoluminescence and long spin coherence times at room temperature, NV centers are particularly worthy of studying in quantum technologies. The study aims to produce NV centers in a controlled manner by using low-energy electron beam irradiation and thermal annealing. The experimental method began with the selection of a nitrogen doped high-pressure high-temperature (HPHT) synthesized type Ib single-crystal plate diamond with a {100} surface orientation, obtained from Element Six. Electron irradiation was carried out using a lithography system at 100 keV with varying doses (0.5–5.0 C/cm²) applied in specific patterns on four corners of this sample. This step aimed to introduce vacancies in a spatially resolved manner. Subsequent annealing at 800 °C under argon flow at 100 CCM was done to induce the migration of these vacancies to nearby substitutional nitrogen atoms. These processes combined lead to the formation of NV centers. A comprehensive characterization process was conducted at each stage using topographical imaging with an optical profilometer, Raman spectroscopy, photoluminescence (PL) spectroscopy, and electron spin resonance (ESR). Raman analysis confirmed the integrity of the diamond lattice post-treatment. It also provided insights into strain–stress relations within the diamond lattice. Shifts in the diamond Raman peak position and changes in full width at half maximum (FWHM) across the sample revealed localized lattice stress. This discovery was important because these stress variations directly influence NV center formation and performance. PL spectroscopy detected distinct zero-phonon line (ZPL) emissions at ~638 nm, indicative of negatively charged NV⁻ centers. The intensity of NV⁻ emission was observed to vary with electron dose, which indicates the ability to control NV center density. Mapping of the PL signal further demonstrated successful spatial control of NVs on the sample. ESR measurements confirmed the spin-related properties of the generated centers and the charge state transition from NV⁰ to NV⁻ following annealing. Overall, this work stands out for its use of low-energy electron irradiation which is preferable due to easier control over defect positioning and potentially lower damage to the host lattice. This thesis contributes to the development of deterministic NV center engineering.

•Apr 14, 2025•0 citations

Effects of Electron Irradiation and Anneal Condition on Creation of Nitrogen-Vacancy Centers in Ib Diamonds

Ishii Shuya, Onoda Shinobu, Abe Hiroshi +1 more

Electron irradiation is one of the most powerful methods to create negatively charged nitrogen-vacancy centers (NV-s) in diamonds, which act as qubits and quantum sensors even at room temperature (RT). For quantum sensing, it is important to create ensemble NV-s with long coherence time (T2) since the sensitivity can be affected by both amount of NV- and T2. For high concentration NV-, electron irradiation with higher fluence is needed. However, if electron fluence is too high, neutral NVs (NV0s) are created because of lack of N donors. For T2, since residual defects act as origins of T2 decoherence, it is important to optimize the condition of subsequent annealing as well as irradiation fluence. Thus, we need to consider initial nitrogen (P1) concentration in diamond, electron fluence, and annealing conditions. In this paper, we create NV-s in Ib diamonds by electron irradiation and subsequent annealing with different conditions, and study the amounts of NV-s and their T2 for high-sensitive quantum sensing. The samples used in this study were Ib diamond with P1 concentration around 100 ppm. Those samples were irradiated with 2 MeV-electrons at a fluence of 1x1018/cm2 at RT. After irradiation, the samples were annealed between 600 and 1400oC in Ar. Photoluminescence (PL) measurements were carried out at RT to confirm NV creation. For PL measurements, the laser with a wavelength of 532 nm was used as excitation. PL intensity for samples annealed at 600 oC is about half even after annealing for 600 min, comparing with that for 800 oC-annealed samples although the values increase with increasing annealing time. Thus, the annealing at 650 oC is not enough to create NV. The samples annealed between 800 and 1200 oC show the highest PL intensity even after annealing for 10 min. The 800 and 1000 oC-annealed samples keep the PL intensity after annealing for 1200 min although the PL intensity for 1200 oC-annealed samples decrease with increasing annealing time above 100 min. The PL intensity for the samples annealed at 1400 oC shows smaller value and decreases with increasing annealing time. For T2, the samples annealed at 1400 oC show 2 microsec after annealing for 10 min. However, NV- cannot be observed after annealing at 1400 oC for 30min. Therefore, it can be concluded that annealing at 1400 oC is not suitable for the creation of NV-. For samples annealed between 600 and 1000 oC, the values of T2 are constant (between 0.5 and 0.9 microsec) after annealing up to 1200 min. For samples annealed at 1200 oC, no significant difference in T2 value is observed from those annealed between 600 and 1000 oC up to 30min, and the value increases with increasing annealing time above 30 min. From the point of view of sensing, it is important to consider both the amounts of NV- centers and T2. Therefore, we compare the values of PL intensity times T2. As a result, the samples annealed between 800 and 1200 oC show the highest value although the value for samples annealed at 1200 oC decreases after annealing for 1200 min. This suggests that annealing at 800 oC for 10 min is enough to create NV-s. We also study the creation of NV-s in diamonds by electron irradiation at elevated temperature. The samples with P1 concentration around 60 and 100 ppm were irradiated with 2 MeV-electrons at fluences up to 5x1018/cm2 at 800 or 1000 oC. The samples were annealed at 1000 oC for 120 min after irradiation. The amounts of NV are estimated from electron spin resonance (ESR) signals. As a result, samples irradiated at 800 and 1000 oC show higher NV- concentration than that for RT-irradiated ones, and 800 oC-irradiated ones show higher NV concentration than 1000oC-irradiated ones. Since the T2 values are not affected by irradiation temperature, the elevated temperature irradiation, especially 800 oC irradiation is a useful method to realize quantum sensing with high sensitivity.

•Jul 10, 2025•0 citations
This thesis reports research conducted on point defects in single crystal diamond utilising the complementary techniques of electron paramagnetic resonance (EPR), optical absorption and photoluminescence (PL) spectroscopy. Intentional silicon-doping of chemical vapour deposition (CVD) diamond allowed the production of samples grown on differently oriented substrates and containing distinct silicon isotopic abundances. The EPR spectrum of the neutral charge state of the silicon split-vacancy centre in diamond, (Si-V)0, has been characterised in the literature. Evidence for the assignment of the 1.31 eV zero phonon line (ZPL) seen in absorption and PL to the 3A2g -> 3A1u transition arising at (Si-V)0 is presented. Reversible charge transfer between the negatively charged centre, (Si-V)− (ZPL at 1.68 eV), and (Si-V)0 enabled the determination of calibration factors relating defect concentrations to their respective ZPL intensities. Preferential alignment of trigonal centres, such as (Si-V), in CVD material grown on {110}-substrates has been observed. The formation of (Si-V) centres during CVD synthesis and via irradiation and annealing of silicon-doped diamond was studied. Variable temperature EPR spectroscopy under illumination was used to investigate the optical spin polarisation (SP) of the (Si-V)0 3A2g ground state. Two different mechanisms for the SP are considered; selective intersystem crossing of (Si-V)0, and photoionisation of (Si-V)−. The properties of (Si-V)0 are compared to those of the extensively studied negatively charged nitrogen vacancy centre, (N-V)−. The effective spin-lattice relaxation and spin polarisation rates for both centres during continuous illumination are explored using pulsed EPR methods. A new defect, labelledWAR3, with spin S = 1 2 was observed in silicon-doped diamond and characterised using multifrequency EPR. Analysis of the data revealed that WAR3 is the neutral charge state of a silicon divacancy complex decorated by a hydrogen atom, (Si-V2:H)0. The experimentally derived 29Si and 1H hyperfine parameters are in good agreement with the values calculated using the spindensity- functional technique, confirming this model and ruling out a non-planar structure.
This thesis explores the generation of nitrogen-vacancy (NV) color centers in diamond, which are solid-state quantum emitters. Quantum emitters are critical for applications in quantum cryptography, sensing, and computing. Due to their stable photoluminescence and long spin coherence times at room temperature, NV centers are particularly worthy of studying in quantum technologies. The study aims to produce NV centers in a controlled manner by using low-energy electron beam irradiation and thermal annealing. The experimental method began with the selection of a nitrogen doped high-pressure high-temperature (HPHT) synthesized type Ib single-crystal plate diamond with a {100} surface orientation, obtained from Element Six. Electron irradiation was carried out using a lithography system at 100 keV with varying doses (0.5–5.0 C/cm²) applied in specific patterns on four corners of this sample. This step aimed to introduce vacancies in a spatially resolved manner. Subsequent annealing at 800 °C under argon flow at 100 CCM was done to induce the migration of these vacancies to nearby substitutional nitrogen atoms. These processes combined lead to the formation of NV centers. A comprehensive characterization process was conducted at each stage using topographical imaging with an optical profilometer, Raman spectroscopy, photoluminescence (PL) spectroscopy, and electron spin resonance (ESR). Raman analysis confirmed the integrity of the diamond lattice post-treatment. It also provided insights into strain–stress relations within the diamond lattice. Shifts in the diamond Raman peak position and changes in full width at half maximum (FWHM) across the sample revealed localized lattice stress. This discovery was important because these stress variations directly influence NV center formation and performance. PL spectroscopy detected distinct zero-phonon line (ZPL) emissions at ~638 nm, indicative of negatively charged NV⁻ centers. The intensity of NV⁻ emission was observed to vary with electron dose, which indicates the ability to control NV center density. Mapping of the PL signal further demonstrated successful spatial control of NVs on the sample. ESR measurements confirmed the spin-related properties of the generated centers and the charge state transition from NV⁰ to NV⁻ following annealing. Overall, this work stands out for its use of low-energy electron irradiation which is preferable due to easier control over defect positioning and potentially lower damage to the host lattice. This thesis contributes to the development of deterministic NV center engineering.
Electron irradiation is one of the most powerful methods to create negatively charged nitrogen-vacancy centers (NV-s) in diamonds, which act as qubits and quantum sensors even at room temperature (RT). For quantum sensing, it is important to create ensemble NV-s with long coherence time (T2) since the sensitivity can be affected by both amount of NV- and T2. For high concentration NV-, electron irradiation with higher fluence is needed. However, if electron fluence is too high, neutral NVs (NV0s) are created because of lack of N donors. For T2, since residual defects act as origins of T2 decoherence, it is important to optimize the condition of subsequent annealing as well as irradiation fluence. Thus, we need to consider initial nitrogen (P1) concentration in diamond, electron fluence, and annealing conditions. In this paper, we create NV-s in Ib diamonds by electron irradiation and subsequent annealing with different conditions, and study the amounts of NV-s and their T2 for high-sensitive quantum sensing. The samples used in this study were Ib diamond with P1 concentration around 100 ppm. Those samples were irradiated with 2 MeV-electrons at a fluence of 1x1018/cm2 at RT. After irradiation, the samples were annealed between 600 and 1400oC in Ar. Photoluminescence (PL) measurements were carried out at RT to confirm NV creation. For PL measurements, the laser with a wavelength of 532 nm was used as excitation. PL intensity for samples annealed at 600 oC is about half even after annealing for 600 min, comparing with that for 800 oC-annealed samples although the values increase with increasing annealing time. Thus, the annealing at 650 oC is not enough to create NV. The samples annealed between 800 and 1200 oC show the highest PL intensity even after annealing for 10 min. The 800 and 1000 oC-annealed samples keep the PL intensity after annealing for 1200 min although the PL intensity for 1200 oC-annealed samples decrease with increasing annealing time above 100 min. The PL intensity for the samples annealed at 1400 oC shows smaller value and decreases with increasing annealing time. For T2, the samples annealed at 1400 oC show 2 microsec after annealing for 10 min. However, NV- cannot be observed after annealing at 1400 oC for 30min. Therefore, it can be concluded that annealing at 1400 oC is not suitable for the creation of NV-. For samples annealed between 600 and 1000 oC, the values of T2 are constant (between 0.5 and 0.9 microsec) after annealing up to 1200 min. For samples annealed at 1200 oC, no significant difference in T2 value is observed from those annealed between 600 and 1000 oC up to 30min, and the value increases with increasing annealing time above 30 min. From the point of view of sensing, it is important to consider both the amounts of NV- centers and T2. Therefore, we compare the values of PL intensity times T2. As a result, the samples annealed between 800 and 1200 oC show the highest value although the value for samples annealed at 1200 oC decreases after annealing for 1200 min. This suggests that annealing at 800 oC for 10 min is enough to create NV-s. We also study the creation of NV-s in diamonds by electron irradiation at elevated temperature. The samples with P1 concentration around 60 and 100 ppm were irradiated with 2 MeV-electrons at fluences up to 5x1018/cm2 at 800 or 1000 oC. The samples were annealed at 1000 oC for 120 min after irradiation. The amounts of NV are estimated from electron spin resonance (ESR) signals. As a result, samples irradiated at 800 and 1000 oC show higher NV- concentration than that for RT-irradiated ones, and 800 oC-irradiated ones show higher NV concentration than 1000oC-irradiated ones. Since the T2 values are not affected by irradiation temperature, the elevated temperature irradiation, especially 800 oC irradiation is a useful method to realize quantum sensing with high sensitivity.