Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Variable Qubit-Qubit Coupling Via a Tunable LC Resonator

C.J. Ballard

Published Jan 1, 2018• 0 citations
Publisher

Abstract

This dissertation examines the design, fabrication, and characterization of a superconducting lumped-element tunable LC resonator that is used to vary the coupling between two superconducting qubits. Some level of qubit-qubit coupling is needed to perform gating operations. However, with fixed coupling, single qubit operations become considerably more difficult due to dispersive shifts in their energy levels transitions that depend on the state of the other qubit. Ideally, one wants a system in which the qubit-qubit coupling can be turned off to allow for single qubit operations, and then turned back on to allow for multi-qubit gate operations. I present results on a device that has two fixed-frequency transmon qubits capacitively coupled to a tunable thin-film LC resonator. The resonator can be tuned in situ over a range of 4.14 GHz to 4.94 GHz by applying an external magnetic flux to two single-Josephson junction loops, which are incorporated into the resonator’s inductance. The qubits have 0-to-1 transition frequencies of 5.10 GHz and 4.74 GHz. To isolate the system and provide a means for reading out the state of the qubit readout, the device was mounted in a 3D Al microwave cavity with a TE101 mode resonance frequency of about 6.1 GHz. The flux-dependent transition frequencies of the system were measured and fit to results from a coupled Hamiltonian model. With the LC resonator tuned to its minimum resonance frequency, I observed a qubit-qubit dispersive shift of 2χ_qq≈ 0.1 MHz, which was less than the linewidth of the qubit transitions. This dispersive shift was sufficiently small to consider the coupling “off”, allowing single qubit operations. The qubit-qubit dispersive shift varied with the applied flux up to a maximum dispersive shift of 2χ_qq≈ 6 MHz. As a proof-of-principle, I present preliminary results on performing a CNOT gate operation on the qubits when the coupling was “on” with 2χ_qq≈ 4 MHz. This dissertation also includes observations of the temperature dependence of the relaxation time T1 of three Al/AlOx/Al transmons. We found that, in some cases, T1 increased by almost a factor of two as the temperature increased from 30 mK to 100 mK. We found that this anomalous behavior was consistent with loss due to non-equilibrium quasiparticles in a transmon where one electrode in the tunnel junction had a smaller volume and slightly smaller superconducting energy gap than the other electrode. At sufficiently low temperatures, non-equilibrium quasiparticles accumulate in the electrode with a smaller gap, leading to an increased density of quasiparticles at the junction and a corresponding decrease in the relaxation time. I present a model of this effect, use the model to extract the density of non-equilibrium quasiparticles in the device, and find the values of the two superconducting energy gaps.

DOI
10.13016/zsk8-ol6u

Related papers

Transmon qubits coupled to superconducting lumped element resonators

Baladitya Suri

I discuss the design, fabrication and measurement at millikelvin-temperatures of Al/AlO$_x$/Al Josephson junction-based transmon qubits coupled to superconducting thin-film lumped element microwave resonators made of aluminum on sapphire. The resonators had a center frequency of around $6\,$GHz, and a total quality factor ranging from 15,000 to 70,000 for the various devices. The area of the transmon junctions was about $150\, \mathrm{nm} \times 150\, \mathrm{nm}$ and with Josephson energy $E_J$ such that $10\,\text{GHz} \leq E_J / h \leq 30\,$GHz. The charging energy of the transmons arising mostly from the large interdigital shunt capacitance, was $E_c / h \approx 300\,$MHz. I present microwave spectroscopy of the devices in the strongly dispersive regime of circuit quantum electrodynamics. In this limit the ac Stark shift due to a single photon in the resonator is greater than the linewidth of the qubit transition. When the resonator is driven coherently using a coupler tone, the transmon spectrum reveals individual ``photon number'' peaks, each corresponding to a single additional photon in the resonator. Using a weighted average of the peak heights in the qubit spectrum, I calculated the average number of photons $\bar{n}$ in the resonator. I also observed a nonlinear variation of $\bar{n}$ with the applied power of the coupler tone $P_{rf}$. I studied this nonlinearity using numerical simulations and found good qualitative agreement with data. In the absence of a coherent drive on the resonator, a thermal population of $5.474\,$GHz photons in the resonator, at an effective temperature of $120\,$mK resulted in a weak $n=1$ thermal photon peak in the qubit spectrum. In the presence of independent coupler and probe tones, the $n=1$ thermal photon peak revealed an Autler-Townes splitting. The observed effect was explained accurately using the four lowest levels of the dispersively dressed Jaynes-Cummings transmon-resonator system, and numerical simulations of the steady-state master equation for the coupled system. I also present time-domain measurements on transmons coupled to lumped-element resonators. From $T_1$ and Rabi oscillation measurements, I found that my early transmon devices (called design LEv5) had lifetimes ($T_1 \sim 1\,\mu$s) limited by strong coupling to the $50\,\Omega$ transmission line. This coupling was characterized by the the rate of change of the Rabi oscillation frequency with the change in the drive voltage ($\mathrm{d}f_{Rabi}\, / \mathrm{d}V$) -- also termed the Rabi coupling to the drive. I studied the design of the transmon-resonator system using circuit analysis and microwave simulations with the aim being to reduce the Rabi coupling to the drive. By increasing the resonance frequency of the resonator $\omega_r/2\pi$ from 5.4$\,$GHz to 7.2$\,$GHz, lowering the coupling of the resonator to the transmission line and thereby increasing the external quality factor $Q_e$ from 20,000 to 70,000, and reducing the transmon-resonator coupling $g/2\pi$ from 70$\,$MHz to 40$\,$MHz, I reduced the Rabi coupling to the drive by an order of magnitude ($\sim$ factor of 20). The $T_1 \sim 4\,\mu$s of devices in the new design (LEv6) was longer than that of the early devices, but still much shorter than the lifetimes predicted from Rabi coupling, suggesting the presence of alternative sources of noise causing qubit relaxation. Microwave simulations and circuit analysis in the presence of a dielectric loss tangent $\tan \delta \simeq 5\times10^{-6}$ agree reasonably well with the measured $T_1$ values, suggesting that surface dielectric loss may be causing relaxation of transmons in the new designs.

•Jan 1, 2015•3 citations

OPTICAL AND ELECTRICAL RESPONSE OF SUPERCONDUCTING RESONATORS FOR A HYBRID QUANTUM SYSTEM

Kristen Voigt

I describe my contributions towards a hybrid quantum system that would have coupled 87Rb atoms to a superconducting device. I first discuss my work coupling an optical fiber to a translatable thin-film LC lumped-element superconducting Al microwave resonator operating at 100 mK in a dilution refrigerator. The LC resonators had resonance frequencies f0 of 6.15 GHz, quality factors Q of 1.5 x 105 to 6.5 x 105 at high powers, and were mounted inside a superconducting aluminum 3D cavity with a resonance frequency of 7.5 GHz and Q of 8 x 103. An optical microfiber (60 µm diameter) passed through a hole in the 3D cavity near the LC resonator. The 3D cavity was mounted on an x-z attocube-translation stage that allowed the LC resonator to be moved relative to the fiber. The resonator’s f0 and Q were affected both by the fiber dielectric perturbing the resonator’s electric field and from scattered light from the fiber. I measured both effects as a function of fiber-resonator position. I modeled the resonator’s optical response by accounting for optical production, recombination, and diffusion of quasiparticles and the non-uniform position-dependent illumination of the resonator. Using the model, I extracted key parameters describing quasiparticles in the resonator. The hybrid quantum system requires the 87Rb and LC resonator resonance to be tuned to the same frequency. I describe our LC resonator tuning method which moves a superconducting Al pin into the resonator’s electric field, decreasing the resonator capacitance and increasing its resonance frequency up to 137 MHz. This was done at 15 mK using an attocube translation stage. I also investigated two-level system (TLS) defects in an LC resonator by applying a dc voltage. I describe a model in which the TLS causes a capacitive perturbation to the resonator rather than the ‘standard’ electric-dipole coupling model. I use this model of a capacitive TLS or cTLS, to describe intermittent telegraph noise measured in the transmission S21 through the resonator. I measured shifts in f0 of more than 6 kHz corresponding to a cTLS fluctuating its capacitance contribution by 430 zF.

•Jan 1, 2021•0 citations

Tunable superconducting transmissionline resonator for qubit coupling

Martin Sandberg

In this licentiate thesis design, fabrication, and measurements of tunable superconducting microwave transmission line resonators are described. The resonators are of quarter wavelength type were the tuning is achieved by changing one of the boundary conditions of the resonator through a tunable impedance. As tunable impedance the Josephson inductance in form of SQUIDs is used. The Josephson inductance can then be tuned by applying a magnetic field to the SQUID loop. A tuning range of 750 MHz for a 5 GHz resonator is achieved, and as a figure of merit it can be tuned over 200 line widths. The purpose of the tunable resonators is to use them for dynamic coupling of superconducting quantum bits, this requires that the resonators can be tuned fast on the timescale of the resonator-qubit coupling. To measure tuning speeds faster then the ring up time of the resonators a method that measures the leakage of energy out of a detuned resonator was developed. With this method a frequency shift of the energy stored in the resonator can be measured. A detuning of 330 MHz in less than 10 ns is demonstrated for a 4.5 GHz resonator with a quality factor of 10$^4$. Working in the few photon limit indicates that the devices can be used to change the frequency of individual photons, this is however still to be demonstrated. As a part of this work the dressed states of a superconducting charge qubit was also studied.

•Jan 1, 2008•0 citations

Coupling a Superconducting Qubit to a Left-Handed Metamaterial Resonator

S. Indrajeet, H. Wang, M.D. Hutchings +4 more

Metamaterial resonant structures made from arrays of superconducting lumped-circuit elements can exhibit microwave-mode spectra with left-handed dispersion for the standing-wave resonances, resulting in a high density of modes in the same frequency range where superconducting qubits are typically operated, as well as a bandgap at lower frequencies that extends down to dc. Using this regime for multimode circuit quantum electrodynamics, we perform a series of measurements of such a superconducting metamaterial resonator coupled to a flux-tunable transmon qubit. Through microwave measurements of the metamaterial, we observe the coupling of the qubit to each of the modes that it passes through. Using a separate readout resonator, we probe the qubit dispersively and characterize the qubit energy relaxation as a function of frequency, which is strongly affected by the Purcell effect in the presence of the dense mode spectrum. Additionally, we investigate the ac Stark shift of the qubit as the photon number in the various metamaterial modes is varied. Through numerical simulations, we explore designs based on this scheme with enhanced coupling so that the coupling energy between the qubit and the metamaterial modes can exceed the intermode spacing in future devices with achievable circuit parameters. The ability to tailor the dense mode spectrum through the choice of circuit parameters and manipulate the photonic state of the metamaterial through interactions with qubits makes this a promising platform for analog quantum simulation with microwave photons and quantum memories.

arXiv:2007.10932•Physical Review Applied•Dec 10, 2020•22 citations

Superconducting flux qubit capacitively coupled to an LC resonator

Tsuyoshi Yamamoto, K. Inomata, Kazuki Koshino +3 more

We study the system where a superconducting flux qubit is capacitively coupled to an LC resonator. In three devices with different coupling capacitance, the magnitude of the dispersive shift is enhanced by the third level of the qubit and quantitatively agrees with the theory. We show by numerical calculation that the capacitive coupling plays an essential role for the enhancement in the dispersive shift. We investigate the coherence properties in two of these devices, which are in the strong-dispersive regime, and show that the qubit energy relaxation is currently not limited by the coupling. We also observe the discrete ac-Stark effect, a hallmark of the strong-dispersive regime, in accordance with the theory.

New Journal of Physics•Jan 10, 2014•32 citations

Fast dynamics and measurements of single-charge devices

Fredrik Persson

In this thesis we present measurements on several different devices, including the single-Cooper-pair box (SCB), the single-electron box, tunable superconducting resonators and so called transmon qubits.By exploiting the quantum capacitance of the SCB, its state was measured by embedding the box in a radio-frequency resonator. The state dependent change in the quantum capacitance then leads to a measurable shift in the resonator’s frequency. On-chip, lumped-element resonators, optimized for speed, were fabricated together with the SCB, which allowed for very fast measurements of the state. We have performed pulsed measurements, and were able to show that the state of the SCB can be measured in approximately 50 ns.The normal state of the box was also measured. We observed a gate dependent absorption in the single-electron box, centered around its degeneracy points, when it was driven by an radio-frequency signal. The internal dynamics of the system was analyzed by solving a two-level master equation. We model the dissipation in the box by defining an effective resistance, which we name the “Sisyphus resistance”. With the developed model, we were able tovery accurately reproduce the measured response over a wide range of RF amplitudes and temperatures.Measurements on a strongly driven SCB are presented. The response of the driven SCB is explained in terms of longitudinal dressed states, defining an effective two-level system. The coherence times of the dressed two-level system are extracted. Relaxation and dephasing in the dressed basis was analyzed.We analyze the possibility of using tunable superconducting resonators for coupling qubits. The resonance frequency is changed by modifying the inductance of a superconducting quantum interference device incorporated into the resonator. The tunability and tuning speed are investigated.We also present measurements on transmon qubits coupled to the tunable cavity. We show Rabi oscillations and observe coherent interaction between two coupled transmon qubits.

•Jan 1, 2010•0 citations
This dissertation examines the design, fabrication, and characterization of a superconducting lumped-element tunable LC resonator that is used to vary the coupling between two superconducting qubits. Some level of qubit-qubit coupling is needed to perform gating operations. However, with fixed coupling, single qubit operations become considerably more difficult due to dispersive shifts in their energy levels transitions that depend on the state of the other qubit. Ideally, one wants a system in which the qubit-qubit coupling can be turned off to allow for single qubit operations, and then turned back on to allow for multi-qubit gate operations. I present results on a device that has two fixed-frequency transmon qubits capacitively coupled to a tunable thin-film LC resonator. The resonator can be tuned in situ over a range of 4.14 GHz to 4.94 GHz by applying an external magnetic flux to two single-Josephson junction loops, which are incorporated into the resonator’s inductance. The qubits have 0-to-1 transition frequencies of 5.10 GHz and 4.74 GHz. To isolate the system and provide a means for reading out the state of the qubit readout, the device was mounted in a 3D Al microwave cavity with a TE101 mode resonance frequency of about 6.1 GHz. The flux-dependent transition frequencies of the system were measured and fit to results from a coupled Hamiltonian model. With the LC resonator tuned to its minimum resonance frequency, I observed a qubit-qubit dispersive shift of 2χ_qq≈ 0.1 MHz, which was less than the linewidth of the qubit transitions. This dispersive shift was sufficiently small to consider the coupling “off”, allowing single qubit operations. The qubit-qubit dispersive shift varied with the applied flux up to a maximum dispersive shift of 2χ_qq≈ 6 MHz. As a proof-of-principle, I present preliminary results on performing a CNOT gate operation on the qubits when the coupling was “on” with 2χ_qq≈ 4 MHz. This dissertation also includes observations of the temperature dependence of the relaxation time T1 of three Al/AlOx/Al transmons. We found that, in some cases, T1 increased by almost a factor of two as the temperature increased from 30 mK to 100 mK. We found that this anomalous behavior was consistent with loss due to non-equilibrium quasiparticles in a transmon where one electrode in the tunnel junction had a smaller volume and slightly smaller superconducting energy gap than the other electrode. At sufficiently low temperatures, non-equilibrium quasiparticles accumulate in the electrode with a smaller gap, leading to an increased density of quasiparticles at the junction and a corresponding decrease in the relaxation time. I present a model of this effect, use the model to extract the density of non-equilibrium quasiparticles in the device, and find the values of the two superconducting energy gaps.
I discuss the design, fabrication and measurement at millikelvin-temperatures of Al/AlOx_xx​/Al Josephson junction-based transmon qubits coupled to superconducting thin-film lumped element microwave resonators made of aluminum on sapphire. The resonators had a center frequency of around 6 6\,6GHz, and a total quality factor ranging from 15,000 to 70,000 for the various devices. The area of the transmon junctions was about 150 nm×150 nm150\, \mathrm{nm} \times 150\, \mathrm{nm}150nm×150nm and with Josephson energy EJE_JEJ​ such that 10 GHz≤EJ/h≤30 10\,\text{GHz} \leq E_J / h \leq 30\,10GHz≤EJ​/h≤30GHz. The charging energy of the transmons arising mostly from the large interdigital shunt capacitance, was Ec/h≈300 E_c / h \approx 300\,Ec​/h≈300MHz. I present microwave spectroscopy of the devices in the strongly dispersive regime of circuit quantum electrodynamics. In this limit the ac Stark shift due to a single photon in the resonator is greater than the linewidth of the qubit transition. When the resonator is driven coherently using a coupler tone, the transmon spectrum reveals individual ``photon number'' peaks, each corresponding to a single additional photon in the resonator. Using a weighted average of the peak heights in the qubit spectrum, I calculated the average number of photons nˉ\bar{n}nˉ in the resonator. I also observed a nonlinear variation of nˉ\bar{n}nˉ with the applied power of the coupler tone PrfP_{rf}Prf​. I studied this nonlinearity using numerical simulations and found good qualitative agreement with data. In the absence of a coherent drive on the resonator, a thermal population of 5.474 5.474\,5.474GHz photons in the resonator, at an effective temperature of 120 120\,120mK resulted in a weak n=1n=1n=1 thermal photon peak in the qubit spectrum. In the presence of independent coupler and probe tones, the n=1n=1n=1 thermal photon peak revealed an Autler-Townes splitting. The observed effect was explained accurately using the four lowest levels of the dispersively dressed Jaynes-Cummings transmon-resonator system, and numerical simulations of the steady-state master equation for the coupled system. I also present time-domain measurements on transmons coupled to lumped-element resonators. From T1T_1T1​ and Rabi oscillation measurements, I found that my early transmon devices (called design LEv5) had lifetimes (T1∼1 μT_1 \sim 1\,\muT1​∼1μs) limited by strong coupling to the 50 Ω50\,\Omega50Ω transmission line. This coupling was characterized by the the rate of change of the Rabi oscillation frequency with the change in the drive voltage (dfRabi /dV\mathrm{d}f_{Rabi}\, / \mathrm{d}VdfRabi​/dV) -- also termed the Rabi coupling to the drive. I studied the design of the transmon-resonator system using circuit analysis and microwave simulations with the aim being to reduce the Rabi coupling to the drive. By increasing the resonance frequency of the resonator ωr/2π\omega_r/2\piωr​/2π from 5.4 \,GHz to 7.2 \,GHz, lowering the coupling of the resonator to the transmission line and thereby increasing the external quality factor QeQ_eQe​ from 20,000 to 70,000, and reducing the transmon-resonator coupling g/2πg/2\pig/2π from 70 \,MHz to 40 \,MHz, I reduced the Rabi coupling to the drive by an order of magnitude (∼\sim∼ factor of 20). The T1∼4 μT_1 \sim 4\,\muT1​∼4μs of devices in the new design (LEv6) was longer than that of the early devices, but still much shorter than the lifetimes predicted from Rabi coupling, suggesting the presence of alternative sources of noise causing qubit relaxation. Microwave simulations and circuit analysis in the presence of a dielectric loss tangent tan⁡δ≃5×10−6\tan \delta \simeq 5\times10^{-6}tanδ≃5×10−6 agree reasonably well with the measured T1T_1T1​ values, suggesting that surface dielectric loss may be causing relaxation of transmons in the new designs.
I describe my contributions towards a hybrid quantum system that would have coupled 87Rb atoms to a superconducting device. I first discuss my work coupling an optical fiber to a translatable thin-film LC lumped-element superconducting Al microwave resonator operating at 100 mK in a dilution refrigerator. The LC resonators had resonance frequencies f0 of 6.15 GHz, quality factors Q of 1.5 x 105 to 6.5 x 105 at high powers, and were mounted inside a superconducting aluminum 3D cavity with a resonance frequency of 7.5 GHz and Q of 8 x 103. An optical microfiber (60 µm diameter) passed through a hole in the 3D cavity near the LC resonator. The 3D cavity was mounted on an x-z attocube-translation stage that allowed the LC resonator to be moved relative to the fiber. The resonator’s f0 and Q were affected both by the fiber dielectric perturbing the resonator’s electric field and from scattered light from the fiber. I measured both effects as a function of fiber-resonator position. I modeled the resonator’s optical response by accounting for optical production, recombination, and diffusion of quasiparticles and the non-uniform position-dependent illumination of the resonator. Using the model, I extracted key parameters describing quasiparticles in the resonator. The hybrid quantum system requires the 87Rb and LC resonator resonance to be tuned to the same frequency. I describe our LC resonator tuning method which moves a superconducting Al pin into the resonator’s electric field, decreasing the resonator capacitance and increasing its resonance frequency up to 137 MHz. This was done at 15 mK using an attocube translation stage. I also investigated two-level system (TLS) defects in an LC resonator by applying a dc voltage. I describe a model in which the TLS causes a capacitive perturbation to the resonator rather than the ‘standard’ electric-dipole coupling model. I use this model of a capacitive TLS or cTLS, to describe intermittent telegraph noise measured in the transmission S21 through the resonator. I measured shifts in f0 of more than 6 kHz corresponding to a cTLS fluctuating its capacitance contribution by 430 zF.
In this licentiate thesis design, fabrication, and measurements of tunable superconducting microwave transmission line resonators are described. The resonators are of quarter wavelength type were the tuning is achieved by changing one of the boundary conditions of the resonator through a tunable impedance. As tunable impedance the Josephson inductance in form of SQUIDs is used. The Josephson inductance can then be tuned by applying a magnetic field to the SQUID loop. A tuning range of 750 MHz for a 5 GHz resonator is achieved, and as a figure of merit it can be tuned over 200 line widths. The purpose of the tunable resonators is to use them for dynamic coupling of superconducting quantum bits, this requires that the resonators can be tuned fast on the timescale of the resonator-qubit coupling. To measure tuning speeds faster then the ring up time of the resonators a method that measures the leakage of energy out of a detuned resonator was developed. With this method a frequency shift of the energy stored in the resonator can be measured. A detuning of 330 MHz in less than 10 ns is demonstrated for a 4.5 GHz resonator with a quality factor of 104^44. Working in the few photon limit indicates that the devices can be used to change the frequency of individual photons, this is however still to be demonstrated. As a part of this work the dressed states of a superconducting charge qubit was also studied.
Metamaterial resonant structures made from arrays of superconducting lumped-circuit elements can exhibit microwave-mode spectra with left-handed dispersion for the standing-wave resonances, resulting in a high density of modes in the same frequency range where superconducting qubits are typically operated, as well as a bandgap at lower frequencies that extends down to dc. Using this regime for multimode circuit quantum electrodynamics, we perform a series of measurements of such a superconducting metamaterial resonator coupled to a flux-tunable transmon qubit. Through microwave measurements of the metamaterial, we observe the coupling of the qubit to each of the modes that it passes through. Using a separate readout resonator, we probe the qubit dispersively and characterize the qubit energy relaxation as a function of frequency, which is strongly affected by the Purcell effect in the presence of the dense mode spectrum. Additionally, we investigate the ac Stark shift of the qubit as the photon number in the various metamaterial modes is varied. Through numerical simulations, we explore designs based on this scheme with enhanced coupling so that the coupling energy between the qubit and the metamaterial modes can exceed the intermode spacing in future devices with achievable circuit parameters. The ability to tailor the dense mode spectrum through the choice of circuit parameters and manipulate the photonic state of the metamaterial through interactions with qubits makes this a promising platform for analog quantum simulation with microwave photons and quantum memories.
We study the system where a superconducting flux qubit is capacitively coupled to an LC resonator. In three devices with different coupling capacitance, the magnitude of the dispersive shift is enhanced by the third level of the qubit and quantitatively agrees with the theory. We show by numerical calculation that the capacitive coupling plays an essential role for the enhancement in the dispersive shift. We investigate the coherence properties in two of these devices, which are in the strong-dispersive regime, and show that the qubit energy relaxation is currently not limited by the coupling. We also observe the discrete ac-Stark effect, a hallmark of the strong-dispersive regime, in accordance with the theory.
In this thesis we present measurements on several different devices, including the single-Cooper-pair box (SCB), the single-electron box, tunable superconducting resonators and so called transmon qubits.By exploiting the quantum capacitance of the SCB, its state was measured by embedding the box in a radio-frequency resonator. The state dependent change in the quantum capacitance then leads to a measurable shift in the resonator’s frequency. On-chip, lumped-element resonators, optimized for speed, were fabricated together with the SCB, which allowed for very fast measurements of the state. We have performed pulsed measurements, and were able to show that the state of the SCB can be measured in approximately 50 ns.The normal state of the box was also measured. We observed a gate dependent absorption in the single-electron box, centered around its degeneracy points, when it was driven by an radio-frequency signal. The internal dynamics of the system was analyzed by solving a two-level master equation. We model the dissipation in the box by defining an effective resistance, which we name the “Sisyphus resistance”. With the developed model, we were able tovery accurately reproduce the measured response over a wide range of RF amplitudes and temperatures.Measurements on a strongly driven SCB are presented. The response of the driven SCB is explained in terms of longitudinal dressed states, defining an effective two-level system. The coherence times of the dressed two-level system are extracted. Relaxation and dephasing in the dressed basis was analyzed.We analyze the possibility of using tunable superconducting resonators for coupling qubits. The resonance frequency is changed by modifying the inductance of a superconducting quantum interference device incorporated into the resonator. The tunability and tuning speed are investigated.We also present measurements on transmon qubits coupled to the tunable cavity. We show Rabi oscillations and observe coherent interaction between two coupled transmon qubits.