Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Applied Sciences

THz Radiation Measurement with HTSC Josephson Junction Detector Matched to Planar Antenna

Eldad Holdengreber, Aviv Glezer Moshe, S. E. Schacham, Moshe Mizrahi, Vigneswaran Dhasarathan, Eliyahu Farber

Published Sep 17, 2020• 7 citations
Publisher

Abstract

Superconducting Josephson junctions have major advantages as detectors of millimeter wave radiation. Frequency of the radiation can be easily derived from the Shapiro steps of the current-voltage characteristics. However, system performance is highly sensitive to impedance mismatch between the antenna and the junction; therefore, optimization is essential. We analyzed and implemented an improved antenna structure, in which the junction is displaced from the antenna center and placed between the ends of two matching strips. Based on theoretical analysis and advanced electromagnetic simulations, we optimized strip dimensions, which affect both the detection magnitude and the frequency of the reflection coefficient dip. Accordingly, two Au bow-tie antennas with different matching strip widths were fabricated. Superconducting Yttrium Barium Copper Oxide (YBCO) thin films were deposited exactly at the bicrystal substrate misorientation points, forming Josephson junctions at the ends of two matching strips. We found a very high correlation between the simulations and the response to Radio Frequency (RF) radiation in the range of 145–165 GHz. Experimental results agree extremely well with the design, showing best performance of both antennas around the frequency for which impedance matching was derived.

DOI
10.3390/app10186482

Related papers

Remote Location of Superconducting Josephson Junction in Planar Antennas for Improved THz Detection

Eldad Holdengreber, Moshe Mizrahi, S. E. Schacham +1 more

Detection of THz radiation can be significantly simplified using a detection system based on Superconducting Josephson junctions. Rather than operating extremely sophisticated conventional electronic equipment, the intensity and frequency can be derived from the Shapiro current steps. However, the detection efficiency is extremely sensitive to impedance mismatch between the antenna and the junction. In our proposed configuration, we displace the junction from the antenna center and placed it between the ends of two matching strips. Extensive simulations of this structure, based on theoretical analysis, show that with proper optimization of strip dimensions, high impedance matching can be obtained for the frequency range of around 265 GHz.

IEEE International Superconductive Electronics Conference (ISEC)•Jul 1, 2019•5 citations

Microwave radiation and sensing of Josephson junction with the log-periodic toothed trapezoid antenna of high T/sub c/ superconducting films

Kwang‐Yong Kang, Insang Song, Y.S. Ha +4 more

Using high temperature superconducting thin films, we designed and fabricated Josephson junctions associated with a log-periodic toothed trapezoid antenna. Microwave self-radiation from the Josephson junction was measured by using both a superheterodyne receiver at the center frequency of 22 GHz and an external waveguide system. In the case of junction incorporated with an antenna structure, there was a significant increase of power by an order of magnitude with respect to a junction without antenna. Under the 22 GHz irradiation, we observed distinctive Shapiro steps in the I-V measurement, which allowed as estimating the received power of the junction. The received power of the junction with an antenna exhibited as a large increase as that of a self-radiation. Our results indicate that a Josephson junction with an antenna is very effective for the microwave coupling between Josephson junction and free space. The combined device can be used either for a high power microwave source or for a high sensitive sensor.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•7 citations

THz Microscopy of Quantum Cascade Laser Radiation Using Josephson Junctions

Julius Mumme, Paul Julius Ritter, Sebastian Gloor +7 more

Josephson junctions (JJs) embedded into the feed point of a thin film antenna made from yttrium barium copper oxide (YBCO) are well suited as a miniature sensor for GHzand THz-frequency fields. A spatially and frequency-resolved image of electromagnetic field intensity is obtained by scanning the region of interest. The sensor is read out by measuring the dc current-voltage (IV) characteristic of the JJ. Discrete frequencies together with their corresponding intensities can be extracted from measurements by evaluating the Shapiro steps in the IV domain. To extract a continuous spectrum from the IV characteristic, the numerical method of Hilbert transform spectroscopy is used and its applicability to our JJs is evaluated. As a benchmark of the setup's capabilities, radiation from a quantum cascade laser (QCL) THz source is characterized both spectrally and spatially. A frequency comb spectrum consistent with the QCL's cavity is revealed by Hilbert transform spectroscopy. The far field radiation patterns of two strong QCL modes are resolved individually and show different characteristics. Optical QCL feedback is observed when the sensor is brought in close proximity.

IEEE Transactions on Applied Superconductivity•Jan 12, 2026•0 citations

Characterization of 40 GHz and 762 GHz sources with superconducting Josephson cantilevers in a THz microscope

Marco Tollkühn, Ilya Elenskiy, Benedikt Hampel +1 more

Josephson cantilevers, based on high temperature superconducting Josephson junctions, are versatile detectors for the measurement of frequency and power of microwave and terahertz radiation. A Josephson cantilever consists of at least one Josephson junction, which is equipped with an antenna structure for better coupling. The Josephson junctions, made from the high-temperature superconductor YBa2Cu3O7, are deployed on LaAIO3or MgO bicrystal substrates. Four feedlines are used to carry out four-terminal sensing. The THz microscope was developed, to allow three dimensional measurements [1]. In this measurement setup, the Josephson cantilever is mounted on a 15 × 15 × 15 mm3positioning system inside a vacuum chamber. The Josephson cantilever is cooled by a cryocooler that allows operating temperatures down to 30 K. A triangular current is injected into the junction and the current-voltage characteristic is recorded at each spatial point. The frequency and the power of the external radiation can be determined from the recorded data by evaluating the occurring Shapiro steps using Hilbert spectroscopy [2]. When the Josephson cantilever is irradiated with more than one frequency at a time, it behaves as a frequency mixer, due to its nonlinear current-voltage characteristic. In this work, we investigated the mixing of 40 GHz and 762 GHz signals with the THz microscope.

IEEE International Superconductive Electronics Conference (ISEC)•Jul 1, 2019•0 citations

Bowtie loaded meander antenna for a high-temperature superconducting terahertz detector and its characterization by the Josephson effect

Mei Yu, Haifeng Geng, Shoulu Jiang +8 more

In a quasi-optical system, the high temperature superconducting terahertz detector often suffers from a fundamental problem of low coupling efficiency with the terahertz signal, especially for the detector based on YBa2Cu3O7-δ (YBCO) bicrystal Josephson junction (JJ) due to a small normal-state resistance. Here, we developed a bowtie loaded meander antenna to enhance coupling efficiency. Differing from the conventional characterization confining on vector network analyzers, we applied three methods to evaluate the antenna, including the measurements of the maximal size of the first order Shapiro step under per incident power, the coupling efficiency between the antenna and the junction, and voltage responsivity. Furthermore, with simulation analysis, we propose that the inductive reactance of the YBCO bicrystal JJ is around 60 ohms under terahertz irradiation at 210 GHz, thus, the reactance is comparable as that of the antenna.

Optics Express•Apr 19, 2020•7 citations

A wideband terahertz high- T c superconducting Josephson-junction mixer: electromagnetic design, analysis and characterization

Xiang Gao, Ting Zhang, Jia Du +3 more

Abstract This paper presents a wideband terahertz (THz) mixer based on a thin-film antenna-coupled high-temperature superconducting (HTS) YBa 2 Cu 3 O 7−x (YBCO) step-edge Josephson junction. The HTS mixer enables the flexible harmonic mixing operation at multiple THz bands with the same microwave local oscillator (LO) source, and features very wide intermediate-frequency or instantaneous bandwidth. In order to optimize the frequency down-conversion performance of the mixer, systematic electromagnetic design and analysis have been carried out to improve the power coupling of THz radiation as well as wideband transmission of microwave signals. Experimental characterization of a fabricated device prototype has demonstrated that the mixer exhibits good performance at both the 200 GHz and 600 GHz bands. Detailed measurement results including the DC characteristics, LO pumping requirement, frequency response, mixing linearity and conversion gain are presented in this paper.

Superconductor Science and Technology•Jun 30, 2017•43 citations
Superconducting Josephson junctions have major advantages as detectors of millimeter wave radiation. Frequency of the radiation can be easily derived from the Shapiro steps of the current-voltage characteristics. However, system performance is highly sensitive to impedance mismatch between the antenna and the junction; therefore, optimization is essential. We analyzed and implemented an improved antenna structure, in which the junction is displaced from the antenna center and placed between the ends of two matching strips. Based on theoretical analysis and advanced electromagnetic simulations, we optimized strip dimensions, which affect both the detection magnitude and the frequency of the reflection coefficient dip. Accordingly, two Au bow-tie antennas with different matching strip widths were fabricated. Superconducting Yttrium Barium Copper Oxide (YBCO) thin films were deposited exactly at the bicrystal substrate misorientation points, forming Josephson junctions at the ends of two matching strips. We found a very high correlation between the simulations and the response to Radio Frequency (RF) radiation in the range of 145–165 GHz. Experimental results agree extremely well with the design, showing best performance of both antennas around the frequency for which impedance matching was derived.
Detection of THz radiation can be significantly simplified using a detection system based on Superconducting Josephson junctions. Rather than operating extremely sophisticated conventional electronic equipment, the intensity and frequency can be derived from the Shapiro current steps. However, the detection efficiency is extremely sensitive to impedance mismatch between the antenna and the junction. In our proposed configuration, we displace the junction from the antenna center and placed it between the ends of two matching strips. Extensive simulations of this structure, based on theoretical analysis, show that with proper optimization of strip dimensions, high impedance matching can be obtained for the frequency range of around 265 GHz.
Using high temperature superconducting thin films, we designed and fabricated Josephson junctions associated with a log-periodic toothed trapezoid antenna. Microwave self-radiation from the Josephson junction was measured by using both a superheterodyne receiver at the center frequency of 22 GHz and an external waveguide system. In the case of junction incorporated with an antenna structure, there was a significant increase of power by an order of magnitude with respect to a junction without antenna. Under the 22 GHz irradiation, we observed distinctive Shapiro steps in the I-V measurement, which allowed as estimating the received power of the junction. The received power of the junction with an antenna exhibited as a large increase as that of a self-radiation. Our results indicate that a Josephson junction with an antenna is very effective for the microwave coupling between Josephson junction and free space. The combined device can be used either for a high power microwave source or for a high sensitive sensor.
Josephson junctions (JJs) embedded into the feed point of a thin film antenna made from yttrium barium copper oxide (YBCO) are well suited as a miniature sensor for GHzand THz-frequency fields. A spatially and frequency-resolved image of electromagnetic field intensity is obtained by scanning the region of interest. The sensor is read out by measuring the dc current-voltage (IV) characteristic of the JJ. Discrete frequencies together with their corresponding intensities can be extracted from measurements by evaluating the Shapiro steps in the IV domain. To extract a continuous spectrum from the IV characteristic, the numerical method of Hilbert transform spectroscopy is used and its applicability to our JJs is evaluated. As a benchmark of the setup's capabilities, radiation from a quantum cascade laser (QCL) THz source is characterized both spectrally and spatially. A frequency comb spectrum consistent with the QCL's cavity is revealed by Hilbert transform spectroscopy. The far field radiation patterns of two strong QCL modes are resolved individually and show different characteristics. Optical QCL feedback is observed when the sensor is brought in close proximity.
Josephson cantilevers, based on high temperature superconducting Josephson junctions, are versatile detectors for the measurement of frequency and power of microwave and terahertz radiation. A Josephson cantilever consists of at least one Josephson junction, which is equipped with an antenna structure for better coupling. The Josephson junctions, made from the high-temperature superconductor YBa2Cu3O7, are deployed on LaAIO3or MgO bicrystal substrates. Four feedlines are used to carry out four-terminal sensing. The THz microscope was developed, to allow three dimensional measurements [1]. In this measurement setup, the Josephson cantilever is mounted on a 15 × 15 × 15 mm3positioning system inside a vacuum chamber. The Josephson cantilever is cooled by a cryocooler that allows operating temperatures down to 30 K. A triangular current is injected into the junction and the current-voltage characteristic is recorded at each spatial point. The frequency and the power of the external radiation can be determined from the recorded data by evaluating the occurring Shapiro steps using Hilbert spectroscopy [2]. When the Josephson cantilever is irradiated with more than one frequency at a time, it behaves as a frequency mixer, due to its nonlinear current-voltage characteristic. In this work, we investigated the mixing of 40 GHz and 762 GHz signals with the THz microscope.
In a quasi-optical system, the high temperature superconducting terahertz detector often suffers from a fundamental problem of low coupling efficiency with the terahertz signal, especially for the detector based on YBa2Cu3O7-δ (YBCO) bicrystal Josephson junction (JJ) due to a small normal-state resistance. Here, we developed a bowtie loaded meander antenna to enhance coupling efficiency. Differing from the conventional characterization confining on vector network analyzers, we applied three methods to evaluate the antenna, including the measurements of the maximal size of the first order Shapiro step under per incident power, the coupling efficiency between the antenna and the junction, and voltage responsivity. Furthermore, with simulation analysis, we propose that the inductive reactance of the YBCO bicrystal JJ is around 60 ohms under terahertz irradiation at 210 GHz, thus, the reactance is comparable as that of the antenna.
Abstract This paper presents a wideband terahertz (THz) mixer based on a thin-film antenna-coupled high-temperature superconducting (HTS) YBa 2 Cu 3 O 7−x (YBCO) step-edge Josephson junction. The HTS mixer enables the flexible harmonic mixing operation at multiple THz bands with the same microwave local oscillator (LO) source, and features very wide intermediate-frequency or instantaneous bandwidth. In order to optimize the frequency down-conversion performance of the mixer, systematic electromagnetic design and analysis have been carried out to improve the power coupling of THz radiation as well as wideband transmission of microwave signals. Experimental characterization of a fabricated device prototype has demonstrated that the mixer exhibits good performance at both the 200 GHz and 600 GHz bands. Detailed measurement results including the DC characteristics, LO pumping requirement, frequency response, mixing linearity and conversion gain are presented in this paper.