In recent years, rapid single flux quantum (RSFQ) circuits, which are promising for the development of high-speed digital electronics, have attracted widespread interest. Niobium nitride (NbN) films have also attracted significant attention for high-frequency applications in superconducting electronics because of their superior material parameters, including their high critical temperature Tc and large gap voltage Vg. To enable the development of all-NbN SFQ circuits, we have developed a fabrication process based on NbN junctions and inductors made of NbN strip lines. It is important to evaluate the inductance because it can affect the performance of an RSFQ circuit and is essential for the RSFQ design. We measured the inductance properties of both epitaxial and polycrystalline NbN strip lines using a superconducting quantum interference device modulation technique at 4.2 K and obtained the width dependence on the inductance of the NbN films. The penetration depth was then calculated from these measurements. The NbN inductance values were calculated numerically with respect to the penetration depth and were then compared with the measured values from the experiments. It was demonstrated that the differences between these values were within 5%. The results reported here will be useful for the design and fabrication of all-NbN RSFQ circuits.
In recent years, rapid single flux quantum (RSFQ) circuits, which are promising for the development of high-speed digital electronics, have attracted widespread interest. Niobium nitride (NbN) films have also attracted significant attention for high-frequency applications in superconducting electronics because of their superior material parameters, including their high critical temperature Tc and large gap voltage Vg. To enable the development of all-NbN SFQ circuits, we have developed a fabrication process based on NbN junctions and inductors made of NbN strip lines. It is important to evaluate the inductance because it can affect the performance of an RSFQ circuit and is essential for the RSFQ design. We measured the inductance properties of both epitaxial and polycrystalline NbN strip lines using a superconducting quantum interference device modulation technique at 4.2 K and obtained the width dependence on the inductance of the NbN films. The penetration depth was then calculated from these measurements. The NbN inductance values were calculated numerically with respect to the penetration depth and were then compared with the measured values from the experiments. It was demonstrated that the differences between these values were within 5%. The results reported here will be useful for the design and fabrication of all-NbN RSFQ circuits.
Abstract Superconducting quantum interference devices (SQUIDs) with 3D nano-bridge junctions can be miniaturized into nano-SQUIDs that are able to sense a few spins in a large magnetic field. Among all device parameters, the inductance is key to the performance of SQUIDs with 3D nano-bridge junctions. Here, we measured the critical-current magnetic flux modulation curves of 12 devices with three design types using a current strip-line directly coupled to the SQUID loop. A best flux modulation depth of 71% was achieved for our 3D Nb SQUID. From the modulation curves, we extracted the inductance values of the current stripe-line in each design and compared them with the corresponding simulation results of InductEX. In this way, London penetration depths of 110 and 420 nm were determined for our Nb (niobium) and NbN (niobium nitride) films, respectively. Furthermore, we showed that inductances of 11 and 119 pH for Nb and NbN 3D nano-bridge junctions, respectively, dominated the total inductance of our SQUID loops which are 23 pH for Nb and 255 pH for NbN. A screening parameter being equal to one suggests optimal critical currents of 89.6 and 8.1 μ A for Nb and NbN SQUIDs, respectively. Additionally, intrinsic flux noise of 110 ± 40 n Φ 0 /(Hz) 1/2 is calculated for the Nb SQUIDs with 3D nano-bridge junctions by Langevin simulation.
Abstract In this paper, we report on a systematic study of the inductance and magnetic field penetration depth (λ) of polycrystalline NbN superconducting thin films. By employing a four-metal-layer fabrication process specifically designed for all-NbN single-flux-quantum circuits, we constructed a superconducting quantum interference device loop composed of two parallel NbN SNS junctions, NbN microstrips, and NbN ground planes for precise inductance measurement. At 4.2 K, as the linewidth increases from 1 μm to 30 μm, the inductance per unit length (L u) of NbN microstrips significantly decreases, for example, the L u of 250 nm thick NbN microstrips drops from 0.907 pH/μm to 0.047 pH/μm. Compared to Nb, the L u of polycrystalline NbN microstrips is approximately two to three times that of Nb, offering an advantage for manufacturing smaller superconducting inductors. Furthermore, we conducted simulation analysis using InductEx software to extract the λ of NbN films of varying thicknesses. The results indicate that as the film thickness increased from 45 nm to 600 nm, λ initially decreased sharply and then stabilized, with values ranging from 430 nm to 323 nm. Notably, once the film thickness exceeded 200 nm, λ remained essentially constant, even at a temperature of 10 K, where it showed good stability, albeit with a slight increase (about 50 nm) compared to 4.2 K. This dependence of λ on thickness is reasonably explained by considering the effects of NbN film thickness on the superconducting critical temperature and residual resistivity. These research findings not only deepen our understanding of the characteristics of superconducting films but also lay a solid foundation for the future design and manufacture of more compact superconducting circuits at the higher temperature of 10 K.
We developed a process for fabricating nitride superconductor-based superconducting qubits monolithically integrated with a single flux quantum (SFQ)-based readout and control circuits. Since we used a Josephson junction (JJ) made of an NbN/AlN/NbN tri-layer, including a critical current density (Jc) of 50 A/cm2as the suitable material for superconducting qubits and SFQ readout/control circuits operating at 20 mK, the JJs for both the qubits and the SFQ circuits could simultaneously be fabricated. The device structure was also composed of three superconductive layers, comprising two superconductive layers as wiring layers and other layers as the top ground plane. Then, we used a Pd film as the resistive layer, which is required as the shunt resistors and the bias resistors for the SFQ control circuits, followed by an investigation of the properties of NbN/AlN/NbN epitaxial junctions and evaluation of the sheet inductance of the base NbN and wiring NbTiN layer. Our results showed the successful fabrication of a JJ with a sufficiently low leakage current and aJcof around 50 A/cm2, which was close to the target value. Furthermore, the evaluated sheet inductance exceeded 1 pH, which was several times larger than the values obtained for Nb-integrated circuits.
A novel approach to modulating the inductance of a superconducting microstrip is described. This approach could be the basis for numerous practical applications, such as phase-shifters and high-frequency tuning elements. The physical mechanisms involved are quasiparticle injection, gap suppression, and penetration-depth modulation. The authors have investigated the modulation of the penetration depth of niobium and niobium nitride films by excess quasiparticle injection. To this effect, all niobium and all-niobium-nitride SQUID (superconducting quantum interference device) circuits were designed and fabricated. These circuits allow quasiparticle injection into the inductive element of the SQUID. This injection is achieved by optical irradiation through an opening in a Nb reflective layer which partially masks the rest of the circuit or electronic current injection through a tunnel junction overlaid on the microstrip inductance. Penetration-depth modulation is achieved with both methods. The magnitude of the effect varies from 10% to over 200% change in inductance.>
Planar niobium nitride (NbN) dc superconducting quantum interference devices (SQUIDs) magnetometers were developed based on high-quality epitaxial NbN/AlN/NbN Josephson junctions for SQUID applications at higher operating temperatures. To improve the design of NbN dc SQUIDs, we measured the SQUID washer's inductance, which is a key SQUID parameter. A set of NbN dc SQUIDs with washers with different dimensions were implemented. The washer inductances were obtained from the periodic flux variation in the SQUIDs when a control current was injected directly into the SQUID washers; the results agree well with the ones calculated with a numerical simulation in InductEX software. We obtained an empirical expression to estimate the NbN SQUID inductance with washers with different geometric structures. Our results will be useful for designing NbN dc SQUID magnetometers in future.
We present the planar microwave filters developed as the front selective and impedance matching circuit for the RSFQ based (Rapid Single Flux Quantum) A/D converters, operating at cryogenic temperature (T = 9 K). The structures are to be patterned in thin NbN (niobium nitride) superconducting films with critical temperature T ap 16 K. The filter design is experimentally verified at lower frequency (f0= 5 GHz, microstrip) on the Ro3006 substrate. During the design, we aim to reach high stopband attenuation and matching of different input - output impedances. The filters use high impedance level in order to obtain suitable dimensions of the lines, important for the final accuracy. A layout of 1 cm2NbN filter designed for f0= 30 GHz and CPW is presented. This NbN filter is intended for the extraction of parameters such as kinetic inductance or London penetration depth, in order to improve the simulation accuracy of our NbN process.