Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Fabrication and Testing of Superconducting Tunnel Junctions for AN SIS Mixer Operating at 265-280 GHZ.

W. H. Mallison

Published Jan 1, 1991• 0 citations
OpenAlex

Related papers

A quantum mixer at 350 GHz based on superconductor-insulator-superconductor (SIS) junctions.

Cornelia E. Honingh

•Jan 1, 1993•2 citations

A 700-GHz SIS Antipodal Finline Mixer Fed by a Pickett–Potter Horn-Reflector Antenna

Phichet Kittara, Paul Grimes, G. Yassin +3 more

We report the successful operation of a superconductor-insulator-superconductor (SIS) finline mixer operating near the superconducting energy gap of Nb. The mixer employs a new type of Pickett-Potter horn-reflector (PPHR) antenna, which exhibits low sidelobes and low cross-polarization levels, and yet is easy to fabricate. The SIS tunnel junction and all of the integrated superconducting tuning circuits are fabricated from Nb using planar-circuit technology. The mixer employs an antipodal finline section, deposited on one side of a quartz substrate, which transforms the high impedance of the waveguide (/spl ap/300 /spl Omega/) to the low impedance of the microstrip line (/spl ap/20 /spl Omega/). The Nb/Al-oxide/Nb tunnel junction is fabricated at the same time as the finline circuit. In this paper, we describe the design and testing of the mixer, and pay particular attention to the electromagnetic design of the PPHR antenna. We investigate the noise temperature and gain of the mixer over 642-714 GHz, and analyze the experimental results using rigorous theories that were developed specifically for the purpose. Our investigation demonstrates that finline mixers have good performance both below and above the superconducting energy gap.

IEEE Transactions on Microwave Theory and Techniques•Oct 1, 2004•20 citations

QUANTUM-LIMITED BROADBAND MIXERS WITH SUPERCONDUCTING TUNNEL JUNCTIONS AT MILLIMETER AND SUBMILLIMETER WAVELENGTHS

史生才, セイサイ シ, Zhenfeng XI

•Sep 30, 1996•0 citations

NbN/MgO/NbN SIS tunnel junctions for submm wave mixers

J. A. Stern, B. D. Hunt, Henry George LeDuc +4 more

The authors report on the fabrication and testing of all-refractory NbN/MgO/NbN SIS (superconductor-insulator-superconductor) tunnel junctions for use as high-frequency mixers. Progress in the development of techniques for the fabrication of submicron-area tunnel junctions is described. Junction structures which have been investigated include mesa, crossline, and edge geometries. Using reactive sputtering techniques, NbN tunnel junctions with critical currents in excess of 10/sup 4/ A/cm/sup 2/ have been fabricated with V/sub m/ values as high as 65 mV and areas down to 0.1 mu m/sup 2/. Specific capacitance measurements on NbN/MgO/NbN mesa-type tunnel junctions give values in the range 60-90 fF/ mu m/sup 2/. These SIS tunnel junctions have been integrated with antennas and coupling structures for mixer tests in a waveguide receiver at 207 GHz. Preliminary mixer results are reported.>

IEEE Transactions on Magnetics•Mar 1, 1989•17 citations

Quasioptical SIS mixer with broadband integrated tuning elements

G. Pance, Noshir Dubash, Michael J. Wengler

The authors have designed and tested a quasioptical superconducting tunnel junction (superconductor-insulator-superconductor, or SIS) mixer with integrated tuning elements. The designs consists of a self-complementary log-periodic antenna, the SIS tunnel junction, and the broadband superconducting tuning circuit. The tuning circuit is placed between the SIS junction and the center of the antenna. Tuning circuits are designed for 98 GHz and 492 GHz. Self-induced resonant steps are observed in I-V curves. Results of noise temperature measurements performed between 89 GHz and 104.4 GHz are reported. Results from the Touchstone simulation program, when run with the actual fabrication process parameters, show agreement with the experiment. Three types of measurements are presented: DC I-V curve measurement, heterodyne detection measurement, and direct detection measurement. All measurements show consistent results and they all agree with the theoretical predictions.>

IEEE Transactions on Applied Superconductivity•Mar 1, 1993•2 citations

Heterodyne mixing at 70 GHz with superconductor-insulator-superconductor tunnel junctions

Hans J. Hartfuss, K. H. Gundlach

International Journal of Infrared and Millimeter Waves•Sep 1, 1981•8 citations
We report the successful operation of a superconductor-insulator-superconductor (SIS) finline mixer operating near the superconducting energy gap of Nb. The mixer employs a new type of Pickett-Potter horn-reflector (PPHR) antenna, which exhibits low sidelobes and low cross-polarization levels, and yet is easy to fabricate. The SIS tunnel junction and all of the integrated superconducting tuning circuits are fabricated from Nb using planar-circuit technology. The mixer employs an antipodal finline section, deposited on one side of a quartz substrate, which transforms the high impedance of the waveguide (/spl ap/300 /spl Omega/) to the low impedance of the microstrip line (/spl ap/20 /spl Omega/). The Nb/Al-oxide/Nb tunnel junction is fabricated at the same time as the finline circuit. In this paper, we describe the design and testing of the mixer, and pay particular attention to the electromagnetic design of the PPHR antenna. We investigate the noise temperature and gain of the mixer over 642-714 GHz, and analyze the experimental results using rigorous theories that were developed specifically for the purpose. Our investigation demonstrates that finline mixers have good performance both below and above the superconducting energy gap.
The authors report on the fabrication and testing of all-refractory NbN/MgO/NbN SIS (superconductor-insulator-superconductor) tunnel junctions for use as high-frequency mixers. Progress in the development of techniques for the fabrication of submicron-area tunnel junctions is described. Junction structures which have been investigated include mesa, crossline, and edge geometries. Using reactive sputtering techniques, NbN tunnel junctions with critical currents in excess of 10/sup 4/ A/cm/sup 2/ have been fabricated with V/sub m/ values as high as 65 mV and areas down to 0.1 mu m/sup 2/. Specific capacitance measurements on NbN/MgO/NbN mesa-type tunnel junctions give values in the range 60-90 fF/ mu m/sup 2/. These SIS tunnel junctions have been integrated with antennas and coupling structures for mixer tests in a waveguide receiver at 207 GHz. Preliminary mixer results are reported.>
The authors have designed and tested a quasioptical superconducting tunnel junction (superconductor-insulator-superconductor, or SIS) mixer with integrated tuning elements. The designs consists of a self-complementary log-periodic antenna, the SIS tunnel junction, and the broadband superconducting tuning circuit. The tuning circuit is placed between the SIS junction and the center of the antenna. Tuning circuits are designed for 98 GHz and 492 GHz. Self-induced resonant steps are observed in I-V curves. Results of noise temperature measurements performed between 89 GHz and 104.4 GHz are reported. Results from the Touchstone simulation program, when run with the actual fabrication process parameters, show agreement with the experiment. Three types of measurements are presented: DC I-V curve measurement, heterodyne detection measurement, and direct detection measurement. All measurements show consistent results and they all agree with the theoretical predictions.>