Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Demonstration of rapid single-flux-quantum RS flip-flop using YBCO/Co-YBCO/YBCO ramp-edge Josephson junction with and without ground plane

강준희, 박종혁, 김준호, 정구락, 성건용, 김창훈, 한택상

Published Jan 1, 2000• 0 citations
OpenAlex

Related papers

Demonstration of Low-Voltage Rapid Single Flux Quantum Circuit Using Unshunted Josephson Junctions

Yuki Hatanaka, Ryo Sato, Masamitsu Tanaka +1 more

IEICE Technical Report; IEICE Tech. Rep.•Apr 13, 2016•0 citations

Observation of the AC Josephson effect up to THz frequencies in YBCO/PBCO/YBCO ramp-type Josephson junctions

D. Terpstra, Augustinus J.H.M. Rijnders, F.H.G. Roesthuis +3 more

Physica C Superconductivity•Nov 1, 1993•8 citations

Fabrication of RS flip-flops using Y-Ba-Cu-O ramp-edge junctions and their operation

J.H. Park, Jangho Kim, Gun Yong Sung +4 more

We fabricated single flux quantum RS flip-flop circuits by using ramp-edge Josephson junctions and tested their performance. The junctions were constructed with two Y/sub 1/Ba/sub 2/Cu/sub 3/O/sub 7-x/ (YBCO) electrodes and a barrier layer. As barrier materials we used cobalt-doped YBCO. To insulate between YBCO layers we used Sr/sub 2/AlTaO/sub 6/ (SAT) thin films. We also fabricated RS flip-flop circuits by using YBCO ground planes to reduce the inductance of YBCO film. The fabricated Josephson junctions showed typical RSJ-like current-voltage (I-V) characteristics above 50 K. We could successfully demonstrate the correct operation of the RS flip-flop circuits at the temperatures near 50 K. We used a computer controlled digital measurement set-up to test the circuits. The RS flip-flop circuit fabricated on a ground plane showed more definite set and reset states on the voltage-flux (V-/spl phi/) modulation curves of the read SQUID than those of the circuit made without ground plane. This may be attributed to the shielding effect by a YBCO ground plane.

IEEE Transactions on Applied Superconductivity•Mar 1, 2001•4 citations

Improvement of the performances of rapid single flux quantum circuit by introducing π-Josephson junctions

Sotaro Nakaishi, Yuki Yamanashi, Nobuyuki Yoshikawa

The Japan Society of Applied Physics•Feb 8, 2018•0 citations

Simulation of a Multi-Josephson Junction Single Flux Quantum Switching Device

Ko Hara, Kobayashi Haruo, Shyuuhei Takagi +1 more

Japanese Journal of Applied Physics•Dec 1, 1980•1 citation

Single flux quantum elements based on a single-layer of a high-T/sub c/ superconductor

V. K. Kaplunenko, Е. А. Степанцов, H. R. Yi +5 more

We have designed, fabricated and successfully tested three SFQ elements: a toggle flip-flop, a SFQ voltage amplifier, and an RS-flip-flop. The design uses a single superconducting layer and it is optimized by repeated computer simulations and repeated inductance calculations. The inductances are made as narrow slits of 0.5 /spl mu/m width. Their values are calculated numerically taking into account material parameters derived from experiment. The YBCO junctions are either of step edge type on LaAlO/sub 3/ substrates or located on two closely spaced bi-crystal grain boundaries on a novel YSZ tricrystal substrate. Carbon masks were used to form steps on LaAlO/sub 3/ substrates and for the YBCO patterning. Voltage amplifier shows operation up to 60 K, and both flip-flops were observed to operate at temperatures up to 30 K with parameters close to the simulated values. The operation frequency of a T-flip-flop cell of about 150 GHz was achieved and a new measurement technique of the margins of an RS trigger is suggested.

IEEE Transactions on Applied Superconductivity•Jun 1, 1997•7 citations
We fabricated single flux quantum RS flip-flop circuits by using ramp-edge Josephson junctions and tested their performance. The junctions were constructed with two Y/sub 1/Ba/sub 2/Cu/sub 3/O/sub 7-x/ (YBCO) electrodes and a barrier layer. As barrier materials we used cobalt-doped YBCO. To insulate between YBCO layers we used Sr/sub 2/AlTaO/sub 6/ (SAT) thin films. We also fabricated RS flip-flop circuits by using YBCO ground planes to reduce the inductance of YBCO film. The fabricated Josephson junctions showed typical RSJ-like current-voltage (I-V) characteristics above 50 K. We could successfully demonstrate the correct operation of the RS flip-flop circuits at the temperatures near 50 K. We used a computer controlled digital measurement set-up to test the circuits. The RS flip-flop circuit fabricated on a ground plane showed more definite set and reset states on the voltage-flux (V-/spl phi/) modulation curves of the read SQUID than those of the circuit made without ground plane. This may be attributed to the shielding effect by a YBCO ground plane.
We have designed, fabricated and successfully tested three SFQ elements: a toggle flip-flop, a SFQ voltage amplifier, and an RS-flip-flop. The design uses a single superconducting layer and it is optimized by repeated computer simulations and repeated inductance calculations. The inductances are made as narrow slits of 0.5 /spl mu/m width. Their values are calculated numerically taking into account material parameters derived from experiment. The YBCO junctions are either of step edge type on LaAlO/sub 3/ substrates or located on two closely spaced bi-crystal grain boundaries on a novel YSZ tricrystal substrate. Carbon masks were used to form steps on LaAlO/sub 3/ substrates and for the YBCO patterning. Voltage amplifier shows operation up to 60 K, and both flip-flops were observed to operate at temperatures up to 30 K with parameters close to the simulated values. The operation frequency of a T-flip-flop cell of about 150 GHz was achieved and a new measurement technique of the margins of an RS trigger is suggested.