Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

OptSp

Nonadiabatic action of kinetic noise on an isolated spectral line

А. П. Коузов

Published Nov 1, 1980• 1 citation
OpenAlex

Related papers

Kinetic Theory of Spectral Line Formation

Joachim Oxenius, E. Simonneau

Annals of Physics•Aug 1, 1994•9 citations

Kinetic Aspects of Redistribution in Spectral Lines

Joachim Oxenius

Springer eBooks•Jan 1, 1985•1 citation

Physical picture of the middle part of the spectral line profile

Stanislav D. Tvorogov

The idea of S. G. Rautian to represent the middle part of the profile of an isolated spectral line as the interference of resonant (the central part of the line) and nonresonant (the peripheral part) interactions is realized for the version based on kinetic equations.

Optics and Spectroscopy•Apr 1, 2001•0 citations

Nonadiabatic transition in a broad-spectrum radiation field

T. A. Vartanyan, Sergey G. Przhibel'skii, N. A. Chigir

Journal of Experimental and Theoretical Physics•Aug 1, 1978•0 citations

A modified Boltzmann kinetic equation for line shape functions

Robert Blackmore

The shape of an isolated spectral transition is analyzed in terms of an approximation to the Waldmann–Snider kinetic equation. This equation is written in the form of a drift and collision operator acting on a density matrix. With the use of the spherical approximation, the collision operator is subdivided into an elastic Boltzmann-like collision term, an inelastic loss term, and a dephasing term. The Boltzmann-like term is responsible for Dicke narrowing of spectral lines, the inelastic loss term leads to line broadening and the dephasing term may contribute both to line broadening and shifting. Simple approximations to these terms are powerful enough to account for some of the details of experimental line shapes such as asymmetrical deviations from a Lorentzian line shape. Model numerical calculations are carried out assuming classical scattering potentials of the form 1/rn in the Boltzmann-like term and single complex frequencies for the other two. It was found that as long as the density was scaled to give the same diffusion constant, the exact form of the scattering cross section had little effect on the final line shape.

The Journal of Chemical Physics•Jul 15, 1987•52 citations

Kinetic Inductance Traveling Wave Amplifier Designs for Practical Microwave Readout Applications

Andrea Giachero, Michael R. Vissers, Jordan Wheeler +6 more

Abstract A Kinetic Inductance Traveling Wave Amplifier (KIT) utilizes the nonlinear kinetic inductance of superconducting films, particularly niobium titanium nitride (NbTiN), for parametric amplification. These amplifiers achieve remarkable performance in terms of gain, bandwidth, and compression power and frequently approach the quantum limit for noise. However, most KIT demonstrations have been isolated from practical device readout systems. Using a KIT as the first amplifier in the readout chain of an unoptimized microwave SQUID multiplexer coupled to a transition-edge sensor microcalorimeter, we see an initial improvement in the flux noise [1]. One challenge in KIT integration is the considerable microwave pump power required to drive the non-linearity. To address this, we have initiated efforts to reduce the pump power by using thinner NbTiN films and an inverted microstrip transmission line design. In this article, we present the new transmission line design, fabrication procedure, and initial device characterization—including gain and added noise. These devices exhibit over 10 dB of gain with a 3 dB bandwidth of approximately 5.5–7.25 GHz, a maximum practical gain of 12 dB, and typical gain ripple under 4 dB peak to peak. We observe an appreciable impedance mismatch in the NbTiN transmission line, which is likely the source of the majority of the gain ripple. Finally, we perform an initial noise characterization and demonstrate system-added noise of three quanta or less over nearly the entire 3 dB bandwidth.

arXiv:2403.11354•Journal of Low Temperature Physics•Apr 5, 2024•16 citations
The shape of an isolated spectral transition is analyzed in terms of an approximation to the Waldmann–Snider kinetic equation. This equation is written in the form of a drift and collision operator acting on a density matrix. With the use of the spherical approximation, the collision operator is subdivided into an elastic Boltzmann-like collision term, an inelastic loss term, and a dephasing term. The Boltzmann-like term is responsible for Dicke narrowing of spectral lines, the inelastic loss term leads to line broadening and the dephasing term may contribute both to line broadening and shifting. Simple approximations to these terms are powerful enough to account for some of the details of experimental line shapes such as asymmetrical deviations from a Lorentzian line shape. Model numerical calculations are carried out assuming classical scattering potentials of the form 1/rn in the Boltzmann-like term and single complex frequencies for the other two. It was found that as long as the density was scaled to give the same diffusion constant, the exact form of the scattering cross section had little effect on the final line shape.
Abstract A Kinetic Inductance Traveling Wave Amplifier (KIT) utilizes the nonlinear kinetic inductance of superconducting films, particularly niobium titanium nitride (NbTiN), for parametric amplification. These amplifiers achieve remarkable performance in terms of gain, bandwidth, and compression power and frequently approach the quantum limit for noise. However, most KIT demonstrations have been isolated from practical device readout systems. Using a KIT as the first amplifier in the readout chain of an unoptimized microwave SQUID multiplexer coupled to a transition-edge sensor microcalorimeter, we see an initial improvement in the flux noise [1]. One challenge in KIT integration is the considerable microwave pump power required to drive the non-linearity. To address this, we have initiated efforts to reduce the pump power by using thinner NbTiN films and an inverted microstrip transmission line design. In this article, we present the new transmission line design, fabrication procedure, and initial device characterization—including gain and added noise. These devices exhibit over 10 dB of gain with a 3 dB bandwidth of approximately 5.5–7.25 GHz, a maximum practical gain of 12 dB, and typical gain ripple under 4 dB peak to peak. We observe an appreciable impedance mismatch in the NbTiN transmission line, which is likely the source of the majority of the gain ripple. Finally, we perform an initial noise characterization and demonstrate system-added noise of three quanta or less over nearly the entire 3 dB bandwidth.