Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Bulletin of the American Physical Society

Qubit fast reset with QubiC

Gang Huang, Yilun Xu, Ravi Naik, Bradley Mitchell, David Santiago, Irfan A. Siddiqi

Published Mar 2, 2020• 1 citation
OpenAlex

Related papers

Fast qubit resetting with a quantum-circuit refrigerator

Timm Mörstedt, Giacomo Catto, A.J. Viitanen +13 more

Bulletin of the American Physical Society•Mar 16, 2021•0 citations

Automatic single qubit characterization with QubiC

Yilun Xu, Gang Huang, Ravi Naik +3 more

Bulletin of the American Physical Society•Mar 5, 2020•3 citations

Fast qubit reset of a low frequency fluxonium circuit

Nathanaël Cottet, Jeremy Stevens, Benjamin Huard

Bulletin of the American Physical Society•Mar 7, 2019•0 citations

Automatic Two-qubit Gate Calibration with QubiC

Yilun Xu, Gang Huang, Ravi Naik +5 more

Bulletin of the American Physical Society•Mar 18, 2021•1 citation

Multipurpose architecture for fast reset and protective readout of superconducting qubits

Jiayu Ding, Yulong Li, He Wang +12 more

The ability to fast reset a qubit state is crucial for quantum information processing. However, to actively reset a qubit requires engineering a pathway to interact with a dissipative bath, which often comes at the cost of reduced qubit protection from the environment. Here, we present a multipurpose architecture that enables fast reset and protection of superconducting qubits during control and readout. In our design, two on-chip diplexers are connected by two transmission lines. The high-pass branch provides a flat passband for convenient allocation of readout resonators above the qubit frequencies, which is preferred for reducing measurement-induced state transitions. In the low-pass branch, we leverage a standing-wave mode below the maximum qubit frequency for a rapid reset. The qubits are located in the common stopband to inhibit dissipation during coherent operations. We demonstrate resetting a transmon qubit from its first excited state to the ground state in 100 ns, achieving a residual population of 2.7%. The reset time may be further shortened to 27 ns by exploiting the coherent population inversion effect. We further extend the technique to resetting the qubit from its second excited state. Our approach promises scalable implementation of fast reset and qubit protection during control and readout, adding to the toolbox of dissipation engineering.

arXiv:2407.21332•Physical Review Applied•Jan 6, 2025•12 citations

Broadband Purcell Filter for Fast Superconducting Qubit Reset and Readout

Yu Zhao, Zhixu Chen, Hanxian Liu +12 more

Rapid reset and readout of qubit states are essential for quantum error correction, yet accelerating these operations through stronger coupling to a dissipative environment inevitably increases qubit decay via the Purcell effect. Here we present a broadband Purcell filter that decouples the reset and readout paths, enabling both operations to be independently optimized without compromising qubit coherence. The filter employs two engineered notches - an intrinsic notch and a bandstop notch - to provide broadband Purcell protection, together with an additional reset stub that creates a reset mode below the protected band. To enable fast reset while suppressing filter-mediated interactions between qubits, we couple each qubit to a dedicated reset resonator. We experimentally demonstrate Purcell-limited relaxation times exceeding 1 ms across a 1.2 GHz bandwidth, simultaneously with 500 ns readout without a Josephson parametric amplifier and 100 ns reset with 99.6% efficiency. The reset resonator is designed with a deliberate kappa-chi mismatch, which suppresses photon-shot-noise-induced dephasing by a factor of 70 compared to the readout resonator. Our work provides a scalable hardware solution that resolves the traditional trade-off between fast qubit operations and qubit protection, advancing the prospects for fault-tolerant quantum computing.

quant-pharXiv:2609.14081•Sep 15, 2026•1 citation
The ability to fast reset a qubit state is crucial for quantum information processing. However, to actively reset a qubit requires engineering a pathway to interact with a dissipative bath, which often comes at the cost of reduced qubit protection from the environment. Here, we present a multipurpose architecture that enables fast reset and protection of superconducting qubits during control and readout. In our design, two on-chip diplexers are connected by two transmission lines. The high-pass branch provides a flat passband for convenient allocation of readout resonators above the qubit frequencies, which is preferred for reducing measurement-induced state transitions. In the low-pass branch, we leverage a standing-wave mode below the maximum qubit frequency for a rapid reset. The qubits are located in the common stopband to inhibit dissipation during coherent operations. We demonstrate resetting a transmon qubit from its first excited state to the ground state in 100 ns, achieving a residual population of 2.7%. The reset time may be further shortened to 27 ns by exploiting the coherent population inversion effect. We further extend the technique to resetting the qubit from its second excited state. Our approach promises scalable implementation of fast reset and qubit protection during control and readout, adding to the toolbox of dissipation engineering.
Rapid reset and readout of qubit states are essential for quantum error correction, yet accelerating these operations through stronger coupling to a dissipative environment inevitably increases qubit decay via the Purcell effect. Here we present a broadband Purcell filter that decouples the reset and readout paths, enabling both operations to be independently optimized without compromising qubit coherence. The filter employs two engineered notches - an intrinsic notch and a bandstop notch - to provide broadband Purcell protection, together with an additional reset stub that creates a reset mode below the protected band. To enable fast reset while suppressing filter-mediated interactions between qubits, we couple each qubit to a dedicated reset resonator. We experimentally demonstrate Purcell-limited relaxation times exceeding 1 ms across a 1.2 GHz bandwidth, simultaneously with 500 ns readout without a Josephson parametric amplifier and 100 ns reset with 99.6% efficiency. The reset resonator is designed with a deliberate kappa-chi mismatch, which suppresses photon-shot-noise-induced dephasing by a factor of 70 compared to the readout resonator. Our work provides a scalable hardware solution that resolves the traditional trade-off between fast qubit operations and qubit protection, advancing the prospects for fault-tolerant quantum computing.