Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE International Superconductive Electronics Conference (ISEC)

High-Frequency Properties of Y-Ba-Cu-O Josephson Junctions Fabricated with Helium Ion Beam Irradiation

Anthony Cortez, Ethan Y. Cho, Hao Li, Daniel Cunnane, Boris S. Karasik, Shane A. Cybart

Published Jul 1, 2019• 2 citations
Publisher

Abstract

We have fabricated spiral THz antennas containing embedded high TCYBa2Cu3O7 (YBCO) focused helium ion beam Josephson junctions (JJ) for characterization of their high frequency characteristics. The values of the resistance and critical current of the junctions are controlled through the irradiation dose and geometry of the junction. We observe several orders of Shapiro steps in the current voltage characteristics of the device when irradiated with 0.6 THz and a single step when irradiated at 2.52 THz.

DOI
10.1109/isec46533.2019.8990898

Related papers

Tuning Y–Ba–Cu–O Focused Helium Ion Beam Josephson Junctions for Use as THz Mixers

Anthony Cortez, Ethan Y. Cho, Hao Li +3 more

We present Josephson junctions fabricated from high transition temperature superconductor YBa2Cu3O7coupled to spiral THz antennas. The fabrication process involves creating a Josephson junction at the center of a superconducting bridge embedded into a THz spiral antenna using irradiation from a focused helium ion beam. For low doses of helium irradiation, the junctions have metallic barriers and operate at temperatures as high as 67 K. For higher doses of irradiation, insulator barriers are created. These devices have higher resistance but require cooling to lower temperatures (~10 K) due to smaller critical currents. Through optimization of the dose and by trimming the width of the junctions, we have created high resistance devices to improve the impedance match to a spiral antenna. Under 90-GHz radiation, we observe up to 17 Shapiro steps in the I-V curve out to approximately 3 mV at a temperature of 10 K.

IEEE Transactions on Applied Superconductivity•Mar 18, 2019•13 citations

YBa$_2$Cu$_3$O$_7$ nano-constriction Josephson junctions and SQUIDs fabricated by focused helium-ion-beam irradiation

Christoph Schmid, Christopher Buckreus, David Haas +9 more

By focused $30\,\mathrm{keV}$ He ion beam irradiation, epitaxially grown YBa$_2$Cu$_3$O$_7$ (YBCO) thin films can be driven from the superconducting to the insulating state with increasing irradiation dose. A properly chosen dose suppresses superconductivity down to $4\,\mathrm{K}$, while crystallinity is still preserved. With this approach we create areas of normal-conducting YBCO that can be used to define resistively shunted constriction-type Josephson junctions (cJJs) on the nanometer scale. We also demonstrate that the fabricated cJJs can be incorporated in direct current superconducting quantum interference devices and can be used as detector junctions in THz antennas.

cond-mat.supr-conCross-listedarXiv:2511.19197•Nov 25, 2025•4 citations

AC Response Across the Metal Insulator Transition of YBCO Josephson Junctions Fabricated with a Helium Ion Beam

Adhilsha Parachikunnumal, Nirjhar Sarkar, Aravind Rajeev Sreeja +5 more

Using focused helium ion beam (FHIB) irradiation, we fabricated in-plane, high-Tc YBCO Josephson junctions. By varying the dose of the irradiation, we tune the junction barriers from metallic (SNS) to insulating (SIS) and investigate how this transition affects microwave-driven dynamics. As the barrier transitions from metallic to insulating, the oscillatory response of the Shapiro steps to the RF power changes dramatically. On either side of the metal-insulator transition, the devices exhibit clean integer Shapiro steps without half-integer features, demonstrating that the current--phase relation is dominated by the first harmonic and that the excess current is minimal. The current-voltage response is well-described by the resistively, capacitively shunted junction model assuming a single-harmonic current--phase relation. This behavior indicates well-controlled junction properties suitable for a wide range of superconducting electronics, including detectors, mixers, and high-density integrated circuits.

arXiv:2601.19235•Jan 27, 2026•0 citations

Dynamic properties of high-Tc superconducting nano-junctions made with a focused helium ion beam

F. Couëdo, P. Amari, C. Feuillet-Palma +5 more

Abstract The Josephson junction (JJ) is the corner stone of superconducting electronics and quantum information processing. While the technology for fabricating low T c JJ is mature and delivers quantum circuits able to reach the “quantum supremacy”, the fabrication of reproducible and low-noise high- T c JJ is still a challenge to be taken up. Here we report on noise properties at RF frequencies of recently introduced high- T c Josephson nano-junctions fabricated by mean of a Helium ion beam focused at sub-nanometer scale on a YBa 2 Cu 3 O 7 thin film. We show that their current-voltage characteristics follow the standard Resistively-Shunted-Junction (RSJ) circuit model, and that their characteristic frequency f c = (2 e / h ) I c R n reaches ~300 GHz at low temperature. Using the “detector response” method, we evidence that the Josephson oscillation linewidth is only limited by the thermal noise in the RSJ model for temperature ranging from T ~ 20 K to 75 K. At lower temperature and for the highest He irradiation dose, the shot noise contribution must also be taken into account when approaching the tunneling regime. We conclude that these Josephson nano-junctions present the lowest noise level possible, which makes them very promising for future applications in the microwave and terahertz regimes.

arXiv:1908.11163•Scientific Reports•Jun 24, 2020•26 citations

AC response across the metal–insulator transition of YBCO Josephson junctions fabricated with a helium-ion beam

Adhilsha Parachikunnumal, Nirjhar Sarkar, Aravind Rajeev Sreeja +5 more

Using focused helium-ion beam irradiation, we fabricated in-plane, high-Tc YBa2Cu3O7−δ Josephson junctions. By varying the dose of the irradiation, we tune the junction barriers from metallic to insulating and investigate how this transition affects microwave-driven dynamics. As the barrier transitions from metallic to insulating, the oscillatory response of the Shapiro steps to the RF power changes dramatically. On either side of the metal–insulator transition, the devices exhibit clean integer Shapiro steps without half-integer features, demonstrating that the current–phase relation is dominated by the first harmonic and that the excess current is minimal. The current–voltage response is well described by the resistively, capacitively shunted junction model assuming a single-harmonic current–phase relation. This behavior indicates well-controlled junction properties suitable for a wide range of superconducting electronics, including detectors, mixers, and high-density integrated circuits.

Applied Physics Letters•Jul 6, 2026•0 citations

Terahertz Shapiro steps in high temperature SNS Josephson junctions

Peter A. Rosenthal, Erich N. Grossman

We have studied the far infrared behavior of high -T/sub c/ superconductor-normal metal-superconductor (SNS) microbridges with T/sub c/>85 K and critical current-resistance products (I/sub c/R/sub N/) as high as 10 mV at 4 K. These are the highest I/sub c/R/sub N/ products reported to date for microfabricated Josephson junctions of any material. The junctions were integrated at the feeds of planar log-periodic antennas made from Au thin films. The junctions had dc normal state resistances R/sub N/ between 6 and 38 /spl Omega/, reasonably well matched to the antenna's estimated RF impedance of 53 /spl Omega/. Far infrared laser radiation at 404, 760, and 992 GHz induced distinct Shapiro steps (i.e. constant voltage steps at voltages n(hf/2e), n=1,2,...) in the current voltage characteristics as well as modulation of the critical current. Steps were observed at voltages up to 17 mV and 6 mV, at temperatures of 9 K and 57 K respectively. This corresponds to maximum Josephson oscillation frequencies of 8 and 3 THz at these temperatures. These are the first far infrared measurements performed on high T/sub c/ junctions. Measurements of the power, frequency, and temperature dependence of the Shapiro steps are presented and discussed in the context of a resistively and capacitively shunted junction (RCSJ) model. A value of 4.5 fF for the junction capacitance is inferred from the hysteresis of the slightly underdamped current-voltage characteristics.>

IEEE Transactions on Microwave Theory and Techniques•Apr 1, 1994•46 citations
We have fabricated spiral THz antennas containing embedded high TCYBa2Cu3O7 (YBCO) focused helium ion beam Josephson junctions (JJ) for characterization of their high frequency characteristics. The values of the resistance and critical current of the junctions are controlled through the irradiation dose and geometry of the junction. We observe several orders of Shapiro steps in the current voltage characteristics of the device when irradiated with 0.6 THz and a single step when irradiated at 2.52 THz.
We present Josephson junctions fabricated from high transition temperature superconductor YBa2Cu3O7coupled to spiral THz antennas. The fabrication process involves creating a Josephson junction at the center of a superconducting bridge embedded into a THz spiral antenna using irradiation from a focused helium ion beam. For low doses of helium irradiation, the junctions have metallic barriers and operate at temperatures as high as 67 K. For higher doses of irradiation, insulator barriers are created. These devices have higher resistance but require cooling to lower temperatures (~10 K) due to smaller critical currents. Through optimization of the dose and by trimming the width of the junctions, we have created high resistance devices to improve the impedance match to a spiral antenna. Under 90-GHz radiation, we observe up to 17 Shapiro steps in the I-V curve out to approximately 3 mV at a temperature of 10 K.
YBa2_22​Cu3_33​O7_77​ nano-constriction Josephson junctions and SQUIDs fabricated by focused helium-ion-beam irradiation
By focused 30 keV30\,\mathrm{keV}30keV He ion beam irradiation, epitaxially grown YBa2_22​Cu3_33​O7_77​ (YBCO) thin films can be driven from the superconducting to the insulating state with increasing irradiation dose. A properly chosen dose suppresses superconductivity down to 4 K4\,\mathrm{K}4K, while crystallinity is still preserved. With this approach we create areas of normal-conducting YBCO that can be used to define resistively shunted constriction-type Josephson junctions (cJJs) on the nanometer scale. We also demonstrate that the fabricated cJJs can be incorporated in direct current superconducting quantum interference devices and can be used as detector junctions in THz antennas.
Using focused helium ion beam (FHIB) irradiation, we fabricated in-plane, high-Tc YBCO Josephson junctions. By varying the dose of the irradiation, we tune the junction barriers from metallic (SNS) to insulating (SIS) and investigate how this transition affects microwave-driven dynamics. As the barrier transitions from metallic to insulating, the oscillatory response of the Shapiro steps to the RF power changes dramatically. On either side of the metal-insulator transition, the devices exhibit clean integer Shapiro steps without half-integer features, demonstrating that the current--phase relation is dominated by the first harmonic and that the excess current is minimal. The current-voltage response is well-described by the resistively, capacitively shunted junction model assuming a single-harmonic current--phase relation. This behavior indicates well-controlled junction properties suitable for a wide range of superconducting electronics, including detectors, mixers, and high-density integrated circuits.
Abstract The Josephson junction (JJ) is the corner stone of superconducting electronics and quantum information processing. While the technology for fabricating low T c JJ is mature and delivers quantum circuits able to reach the “quantum supremacy”, the fabrication of reproducible and low-noise high- T c JJ is still a challenge to be taken up. Here we report on noise properties at RF frequencies of recently introduced high- T c Josephson nano-junctions fabricated by mean of a Helium ion beam focused at sub-nanometer scale on a YBa 2 Cu 3 O 7 thin film. We show that their current-voltage characteristics follow the standard Resistively-Shunted-Junction (RSJ) circuit model, and that their characteristic frequency f c = (2 e / h ) I c R n reaches ~300 GHz at low temperature. Using the “detector response” method, we evidence that the Josephson oscillation linewidth is only limited by the thermal noise in the RSJ model for temperature ranging from T ~ 20 K to 75 K. At lower temperature and for the highest He irradiation dose, the shot noise contribution must also be taken into account when approaching the tunneling regime. We conclude that these Josephson nano-junctions present the lowest noise level possible, which makes them very promising for future applications in the microwave and terahertz regimes.
Using focused helium-ion beam irradiation, we fabricated in-plane, high-Tc YBa2Cu3O7−δ Josephson junctions. By varying the dose of the irradiation, we tune the junction barriers from metallic to insulating and investigate how this transition affects microwave-driven dynamics. As the barrier transitions from metallic to insulating, the oscillatory response of the Shapiro steps to the RF power changes dramatically. On either side of the metal–insulator transition, the devices exhibit clean integer Shapiro steps without half-integer features, demonstrating that the current–phase relation is dominated by the first harmonic and that the excess current is minimal. The current–voltage response is well described by the resistively, capacitively shunted junction model assuming a single-harmonic current–phase relation. This behavior indicates well-controlled junction properties suitable for a wide range of superconducting electronics, including detectors, mixers, and high-density integrated circuits.
We have studied the far infrared behavior of high -T/sub c/ superconductor-normal metal-superconductor (SNS) microbridges with T/sub c/>85 K and critical current-resistance products (I/sub c/R/sub N/) as high as 10 mV at 4 K. These are the highest I/sub c/R/sub N/ products reported to date for microfabricated Josephson junctions of any material. The junctions were integrated at the feeds of planar log-periodic antennas made from Au thin films. The junctions had dc normal state resistances R/sub N/ between 6 and 38 /spl Omega/, reasonably well matched to the antenna's estimated RF impedance of 53 /spl Omega/. Far infrared laser radiation at 404, 760, and 992 GHz induced distinct Shapiro steps (i.e. constant voltage steps at voltages n(hf/2e), n=1,2,...) in the current voltage characteristics as well as modulation of the critical current. Steps were observed at voltages up to 17 mV and 6 mV, at temperatures of 9 K and 57 K respectively. This corresponds to maximum Josephson oscillation frequencies of 8 and 3 THz at these temperatures. These are the first far infrared measurements performed on high T/sub c/ junctions. Measurements of the power, frequency, and temperature dependence of the Shapiro steps are presented and discussed in the context of a resistively and capacitively shunted junction (RCSJ) model. A value of 4.5 fF for the junction capacitance is inferred from the hysteresis of the slightly underdamped current-voltage characteristics.>