Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Impedance Matching of Passive Transmission Line Receivers to Improve Reflections Between RSFQ Logic Cells

Lieze Schindler, Paul le Roux, Coenrad Johann Fourie

Published Jan 7, 2020• 17 citations
Publisher

Abstract

Devices used for rapid single flux quantum (RSFQ) cell interconnects include passive transmission lines (PTLs) and Josephson transmission lines. In this article, we demonstrate software analysis methods with which reflections on PTLs can be improved through impedance matching without compromising the margins of the connected RSFQ logic cells. RSFQ cells are typically designed to connect to PTL transmitters and receivers before attaching the PTL interconnects. These transmitters and receivers are used as matching and buffer stages between the cell and the PTL; and can be adjusted to minimize impedance mismatching. We integrate PTL transmitters and receivers within the RSFQ cell to decrease the amount of Josephson junctions required to incorporate PTL interconnect functionality. Frequency domain analysis on each cell provides equivalent impedance characteristics used for impedance matching.

DOI
10.1109/tasc.2020.2964542

Related papers

Investigation of Passive Transmission Lines for the MIT-LL SFQ5ee Process

Ashish Shukla, Benjamin Chonigman, Anubhav Sahu +3 more

As the complexity of superconductor circuits grows, we envision a dense network of passive transmission lines (PTLs) being used to interconnect cells in rapid-single-flux-quantum (RSFQ) circuits. In our library approach, each cell has dedicated tracks as place holders for routing PTLs. Higher impedance PTLs are desirable due to their narrower width. However, at higher impedance, the margins for the PTL receiver degrade rapidly. We have designed, fabricated, tested, and simulated passive transmission lines (PTLs) for high-speed interconnects in the MIT-LL SFQ5ee 10 kA/cm2process. For the symmetric dual ground planes case, PTLs are in the M1 layer with M0 and M2 ground planes, or in the M3 layer with M2 and M4 ground planes. For the asymmetrical dual ground planes case, PTLs are in M2 or M3 layers with M1 and M4 ground planes. We report ±30% margins for these PTLs. We investigate the receiver margins for these PTLs and report impact of margins as a function of corners, interlayer transitions, variants of drivers, and receivers. We demonstrate 100 GHz PTL operation in ring oscillator measurements. We have also adopted multi-layer multi-conductor transmission line models for PTL simulation. We observe good model-to-hardware correlation for low- and high-frequency operation.

IEEE Transactions on Applied Superconductivity•Mar 8, 2019•30 citations

Design of Passive Transmission Line by Adjusting Intrinsic Parameters of Josephson Junctions

Xi Gao, Minghui Niu, Xiaoping Gao +5 more

Along with the improvement of integration and the requirement of high-speed operation, the passive transmission line (PTL) plays a significant role in superconducting integrated circuits due to its intrinsic advantage of extremely low propagation delay and low signal loss in long-distance transmission. Good impedance matching is critical to reduce the signal reflection in the transmission line and maximize the power transferred. Based on the PTL wiring layer selection under SIMIT-Nb03 process, we studied the equivalent input/output impedance for Josephson junction (JJ) at the IO port and explored a method of impedance matching in rapid-single-flux-quantum circuits by adjusting the Stewart McCumber parameter${\beta }_{\bm{C}}$of the JJ in the design of the PTL's driver and receiver. Furthermore, the accompanying influence from JJ's modified${\beta }_{\bm{C}}$on the performance of the driver and receiver is evaluated to maximize the profit of the functional circuits. The common-used serial resistor is removed to obtain a balanced bias margin for the PTL circuits. The proposed PTL has been designed and tested based on SIMIT-Nb03 fabrication process. In total,$ \pm $30% bias margin for the PTL is achieved at low frequency and high frequency (40 GHz) contrast tests, including operation speed and transmission length as test vector. Additionally, a frequency sweep for 1 mm PTL is performed by the designed ring oscillator on the chip. The maximum working frequency is up to 129 GHz, with a margin duration of 8%.

IEEE Transactions on Applied Superconductivity•May 22, 2023•3 citations

A design approach to passive interconnects for single flux quantum logic circuits

Y. Hashimoto, Shinichi Yorozu, Y. Kameda +1 more

We developed a design approach for interface circuits to connect Single Flux Quantum (SFQ) cells by using passive transmission lines (PTL's). In the approach, an interface circuit between a PTL and JTL is optimized to obtain a standard interface circuit, and then, modifications are made to previously designed SFQ cells and the standard interface circuit to connect the SFQ cells by using PTL's. The key point is the use of approximately the same interface circuit with every SFQ cell to maintain the matching condition between the interface circuit and the PTL's. Based on this approach, we designed an interface circuit and a test circuit composed of two D-flip-flops connected using 2-mm-long PTL's via the interface circuits. The impedance of the PTL was 2 /spl Omega/. We achieved high-speed operation of the test circuit up to 35 GHz with a bias margin of -15/+30%.

IEEE Transactions on Applied Superconductivity•Jun 1, 2003•53 citations

The development and characterisation of a parameterised RSFQ cell library for layout synthesis

Lieze Schindler

ENGLISH ABSTRACT: Superconductor electronics have shown great promise for interfacing quantum computers to conventional electronics. Several superconductor logic families show potential, \nbut one particular logic family has shown reliable results: Rapid Single Flux Quantum \n(RSFQ). RSFQ logic implements single SFQ pulses to represent binary data instead of \nthe traditional voltage levels used by semiconductor electronics. RSFQ is so ubiquitous \nto superconductor digital systems that it serves as the entry to superconductor digital \ndesign. Presently, however, the field of RSFQ logic cell design is very exclusive with \na small number of physicists and engineers able to design efficient RSFQ cells. This \nresearch aims to provide a formalised RSFQ design methodology with education quality \ncircuit theory. Several RSFQ examples are designed, analysed and improved using phasebased circuit equations. Similar to Kirchhoff’s current and voltage laws, these phase-based \nequations can be used to accurately determine the current distribution within a cell. The \ndesign methodology for multi-state RSFQ cells is also discussed. Multiple simulation \nmethods confirming cell functionality and operating margins are also presented. The \neducation regarding the design, analysis and implementation of RSFQ cells is vastly \nexpanded through this research which can accelerate the field of quantum circuit design. \nRSFQ cells can be connected using a non-storing inductive loop, Josephson transmission lines (JTLs) or, alternatively, superconductor passive transmission lines (PTLs) \nto bridge longer distances. Signal transmission of SFQ pulses through PTLs and JTLs \nare analysed and compared. Impedance matching for PTL interconnects to reduce pulse \nreflection is also investigated. \nAn example of a portable RSFQ cell library for layout synthesis is developed as \npart of the IARPA SuperTools program. The challenges of RSFQ cell layouts for the \nMassachusetts Institute of Technology Lincoln Laboratory (MIT-LL) SFQ5ee fabrication \nprocess are discussed. A methodology for establishing a standardised cell layout synthesis \nis presented. The research contributes to the design and characterisation of track routing \narchitecture for RSFQ on a multilayer fabrication process. \nLastly, methods to test fabricated RSFQ circuits are presented. This includes testing \nthe functionality of individual cells, as well as measuring throughput delays. As the SFQ \npulses are only a few picoseconds wide, it is not possible to observe these pulses using \nconventional measuring equipment. The fabricated tests must therefore be designed in \nsuch a way that it is possible to extract meaningful measurements.

•Mar 1, 2021•3 citations

Repeater Insertion in SFQ Interconnect

Tahereh Jabbari, Gleb Krylov, Stephen R. Whiteley +2 more

Superconductive passive transmission lines (PTL) are widely used for signal routing in large-scale rapid single flux quantum (RSFQ) circuits. Due to the imperfect matching of the transmission lines between the driver and receiver, single flux quantum (SFQ) pulses are partially reflected. The round trip propagation time of these reflections can coincide with the following SFQ pulse, resulting in a decrease in bias margins or incorrect circuit behavior. This resonant effect depends upon the length of the PTL and the clock frequency of the signal. A methodology to reduce and manage this effect is the focus of this article. A closed-form expression describing the dependence of the resonance frequency on the length of the PTL is presented. This expression describes a set of forbidden lengths for PTL interconnect segments in RSFQ circuits. The proposed methodology and algorithm insert active PTL-based repeaters into long superconductive interconnect while ensuring the length of the line segment is outside the forbidden region and increasing bias margins.

IEEE Transactions on Applied Superconductivity•Jun 9, 2020•58 citations

Optimization of Passive Transmission Lines for Single Flux Quantum Circuits

Benjamin Chonigman, Ashish Shukla, Mustapha Habib +6 more

Passive transmission lines (PTLs) provide an energy-efficient means of transporting pulsed single flux quantum (SFQ) signals between logic gates and blocks on a chip, or even between chips through a multi-chip module carrier. Although functional up to 70 GHz, our previous designs manifested sharp, length-dependent resonances resulting in diminished operating margins. These are particularly inconvenient since the resonant length is about 1 mm at 40–50 GHz, where most SFQ circuits currently function. To avoid the need to keep the PTLs < 1 mm in length, we have optimized the PTL driver-receiver pairs to sufficiently suppress these resonances; this helps facilitate the use of automated routing tools. We present experimental results, in the 10-70 GHz frequency range, for different driver-receiver pairs designed for PTLs in our dual RSFQ-ERSFQ cell library. This cell library, targeting MIT Lincoln Laboratory's SFQ5ee fabrication process, uses PTLs with two types of ground plane configuration. The first variant has signal in M1 and/or M3 with symmetrical ground planes in M0, M2 and/or M2, M4 respectively. The second variant has signal in M2 and/or M3 with asymmetrical ground planes in M1 and M4. We also present a comparison with wider, 4 Ω, PTLs that are more suitable for transport between distant logic blocks. Next, we present experimental results of PTL lengths ranging from 1.2-12 mm over the same 10-70 GHz frequency range. Finally, we report on the design of circuits for investigating crosstalk between two PTLs and their measurement results.

IEEE Transactions on Applied Superconductivity•Feb 26, 2021•14 citations
Devices used for rapid single flux quantum (RSFQ) cell interconnects include passive transmission lines (PTLs) and Josephson transmission lines. In this article, we demonstrate software analysis methods with which reflections on PTLs can be improved through impedance matching without compromising the margins of the connected RSFQ logic cells. RSFQ cells are typically designed to connect to PTL transmitters and receivers before attaching the PTL interconnects. These transmitters and receivers are used as matching and buffer stages between the cell and the PTL; and can be adjusted to minimize impedance mismatching. We integrate PTL transmitters and receivers within the RSFQ cell to decrease the amount of Josephson junctions required to incorporate PTL interconnect functionality. Frequency domain analysis on each cell provides equivalent impedance characteristics used for impedance matching.
As the complexity of superconductor circuits grows, we envision a dense network of passive transmission lines (PTLs) being used to interconnect cells in rapid-single-flux-quantum (RSFQ) circuits. In our library approach, each cell has dedicated tracks as place holders for routing PTLs. Higher impedance PTLs are desirable due to their narrower width. However, at higher impedance, the margins for the PTL receiver degrade rapidly. We have designed, fabricated, tested, and simulated passive transmission lines (PTLs) for high-speed interconnects in the MIT-LL SFQ5ee 10 kA/cm2process. For the symmetric dual ground planes case, PTLs are in the M1 layer with M0 and M2 ground planes, or in the M3 layer with M2 and M4 ground planes. For the asymmetrical dual ground planes case, PTLs are in M2 or M3 layers with M1 and M4 ground planes. We report ±30% margins for these PTLs. We investigate the receiver margins for these PTLs and report impact of margins as a function of corners, interlayer transitions, variants of drivers, and receivers. We demonstrate 100 GHz PTL operation in ring oscillator measurements. We have also adopted multi-layer multi-conductor transmission line models for PTL simulation. We observe good model-to-hardware correlation for low- and high-frequency operation.
Along with the improvement of integration and the requirement of high-speed operation, the passive transmission line (PTL) plays a significant role in superconducting integrated circuits due to its intrinsic advantage of extremely low propagation delay and low signal loss in long-distance transmission. Good impedance matching is critical to reduce the signal reflection in the transmission line and maximize the power transferred. Based on the PTL wiring layer selection under SIMIT-Nb03 process, we studied the equivalent input/output impedance for Josephson junction (JJ) at the IO port and explored a method of impedance matching in rapid-single-flux-quantum circuits by adjusting the Stewart McCumber parameterβC{\beta }_{\bm{C}}βC​of the JJ in the design of the PTL's driver and receiver. Furthermore, the accompanying influence from JJ's modifiedβC{\beta }_{\bm{C}}βC​on the performance of the driver and receiver is evaluated to maximize the profit of the functional circuits. The common-used serial resistor is removed to obtain a balanced bias margin for the PTL circuits. The proposed PTL has been designed and tested based on SIMIT-Nb03 fabrication process. In total,$ \pm $30% bias margin for the PTL is achieved at low frequency and high frequency (40 GHz) contrast tests, including operation speed and transmission length as test vector. Additionally, a frequency sweep for 1 mm PTL is performed by the designed ring oscillator on the chip. The maximum working frequency is up to 129 GHz, with a margin duration of 8%.
We developed a design approach for interface circuits to connect Single Flux Quantum (SFQ) cells by using passive transmission lines (PTL's). In the approach, an interface circuit between a PTL and JTL is optimized to obtain a standard interface circuit, and then, modifications are made to previously designed SFQ cells and the standard interface circuit to connect the SFQ cells by using PTL's. The key point is the use of approximately the same interface circuit with every SFQ cell to maintain the matching condition between the interface circuit and the PTL's. Based on this approach, we designed an interface circuit and a test circuit composed of two D-flip-flops connected using 2-mm-long PTL's via the interface circuits. The impedance of the PTL was 2 /spl Omega/. We achieved high-speed operation of the test circuit up to 35 GHz with a bias margin of -15/+30%.
ENGLISH ABSTRACT: Superconductor electronics have shown great promise for interfacing quantum computers to conventional electronics. Several superconductor logic families show potential, \nbut one particular logic family has shown reliable results: Rapid Single Flux Quantum \n(RSFQ). RSFQ logic implements single SFQ pulses to represent binary data instead of \nthe traditional voltage levels used by semiconductor electronics. RSFQ is so ubiquitous \nto superconductor digital systems that it serves as the entry to superconductor digital \ndesign. Presently, however, the field of RSFQ logic cell design is very exclusive with \na small number of physicists and engineers able to design efficient RSFQ cells. This \nresearch aims to provide a formalised RSFQ design methodology with education quality \ncircuit theory. Several RSFQ examples are designed, analysed and improved using phasebased circuit equations. Similar to Kirchhoff’s current and voltage laws, these phase-based \nequations can be used to accurately determine the current distribution within a cell. The \ndesign methodology for multi-state RSFQ cells is also discussed. Multiple simulation \nmethods confirming cell functionality and operating margins are also presented. The \neducation regarding the design, analysis and implementation of RSFQ cells is vastly \nexpanded through this research which can accelerate the field of quantum circuit design. \nRSFQ cells can be connected using a non-storing inductive loop, Josephson transmission lines (JTLs) or, alternatively, superconductor passive transmission lines (PTLs) \nto bridge longer distances. Signal transmission of SFQ pulses through PTLs and JTLs \nare analysed and compared. Impedance matching for PTL interconnects to reduce pulse \nreflection is also investigated. \nAn example of a portable RSFQ cell library for layout synthesis is developed as \npart of the IARPA SuperTools program. The challenges of RSFQ cell layouts for the \nMassachusetts Institute of Technology Lincoln Laboratory (MIT-LL) SFQ5ee fabrication \nprocess are discussed. A methodology for establishing a standardised cell layout synthesis \nis presented. The research contributes to the design and characterisation of track routing \narchitecture for RSFQ on a multilayer fabrication process. \nLastly, methods to test fabricated RSFQ circuits are presented. This includes testing \nthe functionality of individual cells, as well as measuring throughput delays. As the SFQ \npulses are only a few picoseconds wide, it is not possible to observe these pulses using \nconventional measuring equipment. The fabricated tests must therefore be designed in \nsuch a way that it is possible to extract meaningful measurements.
Superconductive passive transmission lines (PTL) are widely used for signal routing in large-scale rapid single flux quantum (RSFQ) circuits. Due to the imperfect matching of the transmission lines between the driver and receiver, single flux quantum (SFQ) pulses are partially reflected. The round trip propagation time of these reflections can coincide with the following SFQ pulse, resulting in a decrease in bias margins or incorrect circuit behavior. This resonant effect depends upon the length of the PTL and the clock frequency of the signal. A methodology to reduce and manage this effect is the focus of this article. A closed-form expression describing the dependence of the resonance frequency on the length of the PTL is presented. This expression describes a set of forbidden lengths for PTL interconnect segments in RSFQ circuits. The proposed methodology and algorithm insert active PTL-based repeaters into long superconductive interconnect while ensuring the length of the line segment is outside the forbidden region and increasing bias margins.
Passive transmission lines (PTLs) provide an energy-efficient means of transporting pulsed single flux quantum (SFQ) signals between logic gates and blocks on a chip, or even between chips through a multi-chip module carrier. Although functional up to 70 GHz, our previous designs manifested sharp, length-dependent resonances resulting in diminished operating margins. These are particularly inconvenient since the resonant length is about 1 mm at 40–50 GHz, where most SFQ circuits currently function. To avoid the need to keep the PTLs < 1 mm in length, we have optimized the PTL driver-receiver pairs to sufficiently suppress these resonances; this helps facilitate the use of automated routing tools. We present experimental results, in the 10-70 GHz frequency range, for different driver-receiver pairs designed for PTLs in our dual RSFQ-ERSFQ cell library. This cell library, targeting MIT Lincoln Laboratory's SFQ5ee fabrication process, uses PTLs with two types of ground plane configuration. The first variant has signal in M1 and/or M3 with symmetrical ground planes in M0, M2 and/or M2, M4 respectively. The second variant has signal in M2 and/or M3 with asymmetrical ground planes in M1 and M4. We also present a comparison with wider, 4 Ω, PTLs that are more suitable for transport between distant logic blocks. Next, we present experimental results of PTL lengths ranging from 1.2-12 mm over the same 10-70 GHz frequency range. Finally, we report on the design of circuits for investigating crosstalk between two PTLs and their measurement results.