Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Microdiamond-doped lead-silicate glass optical fibre for remote magnetometry

Dongbi Bai, Hoa Tran My Huynh, David Simpson, Shahraam Afshar Vahid, Philipp Reineck, Andrew D. Greentree, Scott B. Foster, Heike Ebendorff‐Heidepriem, Brant C. Gibson

Published Dec 30, 2019• 1 citation
Publisher

Abstract

We demonstrate fabrication and characterizations of intrinsically magneto-sensitive fiber with potential applications as a high-efficiency remote magnetic field sensing platform. The fibre was fabricated using lead-silicate glass and the rod-intube fibre drawing technique. The thin glass rod of ~1 mm diameter was first coated with nitrogen-vacancy (NV) centreenriched diamond particles of ~1 μm diameter, and subsequently inserted into the glass outer tube. This rod-in-tube assembly was drawn down to fibre, with the diamond particles distributed at the fused interface between rod and tube. We experimentally coupled 532 nm continuous-wave laser into a 30-cm-length fibre piece from the fibre endface, and examined the photoluminescence (PL) properties of the fibre from both the side of the fibre and the output end of the fibre. PL mapping results showed that the glass-embedded NV emitters showed bright and photostable fluorescence, demonstrating characteristic NV centre zero phonon line emission. Moreover, the mapping result obtained at the output end of fibre indicated that the transmitted NV fluorescence was coupled into the propagation modes of the fibre. By using optically detected magnetic resonance (ODMR) from the NV ensemble along the fibre, we demonstrate detection of local magnetic fields via longitudinal excitation and side collection. Based on the current light transmission and collection configuration, the hybrid diamond-glass optical fibre sensor demonstrated a shot noise-limited DC magnetic field sensitivity of 3.7 μT/√Hz at room temperature. Our results open the possibility of robust, field-deployable fibre optical magnetometry.

DOI
10.1117/12.2539124

Related papers

Fluorescent diamond microparticle doped glass fiber for magnetic field sensing

D. Bai, M. H. Huynh, David Simpson +6 more

Diamond containing the nitrogen-vacancy (NV) center is emerging as a significant sensing platform. However, most NV sensors require microscopes to collect the fluorescence signals and therefore are limited to laboratory settings. By embedding micron-scale diamond particles at an annular interface within the cross section of a silicate glass fiber, we demonstrate a robust fiber material capable of sensing magnetic fields. Luminescence spectroscopy and electron spin resonance characterization reveal that the optical properties of NV centers in the diamond microcrystals are well preserved throughout the fiber drawing process. The hybrid fiber presents a low propagation loss of ∼4.0 dB/m in the NV emission spectral window, permitting remote monitoring of the optically detected magnetic resonance signals. We demonstrate NV-spin magnetic resonance readout through 50 cm of fiber. This study paves a way for the scalable fabrication of fiber-based diamond sensors for field-deployable quantum metrology applications.

arXiv:2004.03344•APL Materials•Aug 1, 2020•48 citations

Magnetically sensitive fiber probe with nitrogen-vacancy center nanodiamonds integrated in a suspended core

Adam Filipkowski, Mariusz Mrózek, Grzegorz Stępniewski +6 more

Efficient collection of photoluminescence arising from spin dynamics of nitrogen vacancy (NV) centers in diamond is important for practical applications involving precise magnetic field or temperature mapping. These goals may be realized by the integration of nanodiamond particles with optical fibers and volumetric doping of the particles alongside the fiber core. That approach combines the advantages of robust axial fixation of NV diamonds with a direct spatial overlap of their fluorescence with the guided mode of the fiber. We developed a suspended core silicate glass fiber with 750 nm-diameter nanodiamonds located centrally in the 1.5 µm-core cross-section along its axis. The developed fiber probe was tested for its magnetic sensing performance in optically detected magnetic resonance measurements using a 24 cm-long fiber sample, with the NV excitation and fluorescence collection from the far ends of the sample and yielding optical readout contrast of 7% resulting in 0.5 µT·Hz-1/2 magnetic field sensitivity, two orders of magnitude better than in earlier designs. Thanks to its improved fluorescence confinement, the developed probe could find application in magnetic sensing over extended fiber length, magnetic field mapping or gradiometry.

Optics Express•May 3, 2022•20 citations

Volumetric incorporation of NV diamond emitters in nanostructured F2 glass magneto-optical fiber probes

Adam Filipkowski, Mariusz Mrózek, Grzegorz Stępniewski +10 more

Integration of optically active diamond particles with glass fibers is a powerful method of scaling diamond's magnetic sensing functionality. We propose a novel approach for the integration of diamond particles containing nitrogen-vacancy centers directly into the fiber core. The core is fabricated by stacking the preform from 790 soft glass canes, drawn from a single rod dip-coated with submicron diamond particles suspended in isopropyl alcohol. This enables manual control over the distribution of nanoscale features, here – the diamond particles across the optical fiber core. We verify this by mapping the diamond distribution in the core using confocal microscopy. The particles are separated longitudinally by 12–29 μm, while in the transverse plane a separation of approximately 1.5–2.2 μm is observed, corresponding to the individual cane diameter in the final fiber, and without significant agglomeration. The fiber's magnetic sensitivity is confirmed in optically detected magnetic resonance recorded with a coiled, 60-cm-long fiber sample with readout contrast of 1.3% limited by microwave antenna coverage. Moreover, magnetic-field dependence of the NV─ fluorescence intensity is demonstrated in the absence of microwaves, allowing magnetometric applications with a large (from 0 to 35 mT) B-field dynamic range.

arXiv:2108.13193•Carbon•Apr 11, 2022•28 citations

Optical fibers doped with nitrogen-vacancy submicron diamonds as magnetic sensors

Mariusz Mrózek, Adam Filipkowski, Grzegorz Stępniewski +4 more

Coupling NV-rich diamond with optical fibers opens the door to guiding quantum information via the NV center's spin state. While diamond-functionalized fiber sensors have shown excellent sensitivity to localized magnetic fields, their distributed sensing capabilities have been untapped. By embedding diamonds throughout the fiber's core, we create a sensor sensitive to magnetic fields along its entire length. This theoretically allows for distributed optical readout of small magnetic fields. However, challenges remain in pinpointing the source's location and understanding the performance of a sensor where the NV-center fluorescence is detected at a single endpoint, integrating signals from color centers in varying field and microwave conditions. We present a demonstration of distributed magnetic field sensing using a step-index fiber with NV-rich diamonds incorporated throughout the core. By collecting the NV fluorescence at the fiber's output and recording Optically Detected Magnetic Resonance (ODMR) spectra as the excitation source moves, we can map the magnetic field profile along the fiber, accurately locating the field source. This straightforward sensor design holds promise for applications such as magnetic field mapping of integrated circuits in photonics and spintronics.

Workshop on Specialty Optical Fibers and Their Applications (WSOF)•May 29, 2025•0 citations

Preferential coupling of diamond NV centres in step-index fibres

Shuo Li, Dongbi Bai, Marco Capelli +7 more

Diamonds containing the negatively charged nitrogen-vacancy centre are a promising system for room-temperature magnetometry. The combination of nano- and micro-diamond particles with optical fibres provides an option for deploying nitrogen-vacancy magnetometers in harsh and challenging environments. Here we numerically explore the coupling efficiency from nitrogen-vacancy centres within a diamond doped at the core/clad interface across a range of commercially available fibre types so as to inform the design process for a diamond in fibre magnetometers. We determine coupling efficiencies from nitrogen-vacancy centres to the guided modes of a step-index fibre and predict the optically detected magnetic resonance (ODMR) generated by a ensemble of four nitrogen-vacancy centres in this hybrid fibre system. Our results show that the coupling efficiency is enhanced with a high refractive index difference between the fibre core and cladding and depends on the radial position of the nitrogen-vacancy centres in the fibre core. Our ODMR simulations show that due to the preferential coupling of the nitrogen-vacancy emission to the fibre guided modes, certain magnetometry features such as ODMR contrast can be enhanced and lead to improved sensitivity in such diamond-fibre systems, relative to conventional diamond only ensemble geometries.

Optics Express•Mar 26, 2021•8 citations

High Field Diamond Magnetometry Towards Tokamak Diagnostics

S. M. Graham, C. J. Stephen, A. J. Newman +3 more

Nitrogen vacancy centres (NVC) in diamond have been widely used for near-dc magnetometry. The intrinsic properties of diamonds make them potential candidates for tokamak fusion power diagnostics, where radiation-hard magnetometers will be essential for efficient control. An NVC magnetometer placed in a tokamak will need to operate within a $\geq$ 1 T magnetic field. In this work, we demonstrate fibre-coupled ensemble NVC optically detected magnetic resonance (ODMR) and magnetometry measurements at magnetic fields up to 1.2 T. Sensitivities of approximately 240 to 600 nT/$\sqrt{\textrm{Hz}}$ and 110 nT/$\sqrt{\textrm{Hz}}$ are achieved in a (10-150) Hz frequency range, for non-degenerate and near-$\langle$111$\rangle$ field alignments respectively.

physics.app-phCross-listedarXiv:2601.13413•Jan 21, 2026
We demonstrate fabrication and characterizations of intrinsically magneto-sensitive fiber with potential applications as a high-efficiency remote magnetic field sensing platform. The fibre was fabricated using lead-silicate glass and the rod-intube fibre drawing technique. The thin glass rod of ~1 mm diameter was first coated with nitrogen-vacancy (NV) centreenriched diamond particles of ~1 μm diameter, and subsequently inserted into the glass outer tube. This rod-in-tube assembly was drawn down to fibre, with the diamond particles distributed at the fused interface between rod and tube. We experimentally coupled 532 nm continuous-wave laser into a 30-cm-length fibre piece from the fibre endface, and examined the photoluminescence (PL) properties of the fibre from both the side of the fibre and the output end of the fibre. PL mapping results showed that the glass-embedded NV emitters showed bright and photostable fluorescence, demonstrating characteristic NV centre zero phonon line emission. Moreover, the mapping result obtained at the output end of fibre indicated that the transmitted NV fluorescence was coupled into the propagation modes of the fibre. By using optically detected magnetic resonance (ODMR) from the NV ensemble along the fibre, we demonstrate detection of local magnetic fields via longitudinal excitation and side collection. Based on the current light transmission and collection configuration, the hybrid diamond-glass optical fibre sensor demonstrated a shot noise-limited DC magnetic field sensitivity of 3.7 μT/√Hz at room temperature. Our results open the possibility of robust, field-deployable fibre optical magnetometry.
Diamond containing the nitrogen-vacancy (NV) center is emerging as a significant sensing platform. However, most NV sensors require microscopes to collect the fluorescence signals and therefore are limited to laboratory settings. By embedding micron-scale diamond particles at an annular interface within the cross section of a silicate glass fiber, we demonstrate a robust fiber material capable of sensing magnetic fields. Luminescence spectroscopy and electron spin resonance characterization reveal that the optical properties of NV centers in the diamond microcrystals are well preserved throughout the fiber drawing process. The hybrid fiber presents a low propagation loss of ∼4.0 dB/m in the NV emission spectral window, permitting remote monitoring of the optically detected magnetic resonance signals. We demonstrate NV-spin magnetic resonance readout through 50 cm of fiber. This study paves a way for the scalable fabrication of fiber-based diamond sensors for field-deployable quantum metrology applications.
Efficient collection of photoluminescence arising from spin dynamics of nitrogen vacancy (NV) centers in diamond is important for practical applications involving precise magnetic field or temperature mapping. These goals may be realized by the integration of nanodiamond particles with optical fibers and volumetric doping of the particles alongside the fiber core. That approach combines the advantages of robust axial fixation of NV diamonds with a direct spatial overlap of their fluorescence with the guided mode of the fiber. We developed a suspended core silicate glass fiber with 750 nm-diameter nanodiamonds located centrally in the 1.5 µm-core cross-section along its axis. The developed fiber probe was tested for its magnetic sensing performance in optically detected magnetic resonance measurements using a 24 cm-long fiber sample, with the NV excitation and fluorescence collection from the far ends of the sample and yielding optical readout contrast of 7% resulting in 0.5 µT·Hz-1/2 magnetic field sensitivity, two orders of magnitude better than in earlier designs. Thanks to its improved fluorescence confinement, the developed probe could find application in magnetic sensing over extended fiber length, magnetic field mapping or gradiometry.
Integration of optically active diamond particles with glass fibers is a powerful method of scaling diamond's magnetic sensing functionality. We propose a novel approach for the integration of diamond particles containing nitrogen-vacancy centers directly into the fiber core. The core is fabricated by stacking the preform from 790 soft glass canes, drawn from a single rod dip-coated with submicron diamond particles suspended in isopropyl alcohol. This enables manual control over the distribution of nanoscale features, here – the diamond particles across the optical fiber core. We verify this by mapping the diamond distribution in the core using confocal microscopy. The particles are separated longitudinally by 12–29 μm, while in the transverse plane a separation of approximately 1.5–2.2 μm is observed, corresponding to the individual cane diameter in the final fiber, and without significant agglomeration. The fiber's magnetic sensitivity is confirmed in optically detected magnetic resonance recorded with a coiled, 60-cm-long fiber sample with readout contrast of 1.3% limited by microwave antenna coverage. Moreover, magnetic-field dependence of the NV─ fluorescence intensity is demonstrated in the absence of microwaves, allowing magnetometric applications with a large (from 0 to 35 mT) B-field dynamic range.
Coupling NV-rich diamond with optical fibers opens the door to guiding quantum information via the NV center's spin state. While diamond-functionalized fiber sensors have shown excellent sensitivity to localized magnetic fields, their distributed sensing capabilities have been untapped. By embedding diamonds throughout the fiber's core, we create a sensor sensitive to magnetic fields along its entire length. This theoretically allows for distributed optical readout of small magnetic fields. However, challenges remain in pinpointing the source's location and understanding the performance of a sensor where the NV-center fluorescence is detected at a single endpoint, integrating signals from color centers in varying field and microwave conditions. We present a demonstration of distributed magnetic field sensing using a step-index fiber with NV-rich diamonds incorporated throughout the core. By collecting the NV fluorescence at the fiber's output and recording Optically Detected Magnetic Resonance (ODMR) spectra as the excitation source moves, we can map the magnetic field profile along the fiber, accurately locating the field source. This straightforward sensor design holds promise for applications such as magnetic field mapping of integrated circuits in photonics and spintronics.
Diamonds containing the negatively charged nitrogen-vacancy centre are a promising system for room-temperature magnetometry. The combination of nano- and micro-diamond particles with optical fibres provides an option for deploying nitrogen-vacancy magnetometers in harsh and challenging environments. Here we numerically explore the coupling efficiency from nitrogen-vacancy centres within a diamond doped at the core/clad interface across a range of commercially available fibre types so as to inform the design process for a diamond in fibre magnetometers. We determine coupling efficiencies from nitrogen-vacancy centres to the guided modes of a step-index fibre and predict the optically detected magnetic resonance (ODMR) generated by a ensemble of four nitrogen-vacancy centres in this hybrid fibre system. Our results show that the coupling efficiency is enhanced with a high refractive index difference between the fibre core and cladding and depends on the radial position of the nitrogen-vacancy centres in the fibre core. Our ODMR simulations show that due to the preferential coupling of the nitrogen-vacancy emission to the fibre guided modes, certain magnetometry features such as ODMR contrast can be enhanced and lead to improved sensitivity in such diamond-fibre systems, relative to conventional diamond only ensemble geometries.
Nitrogen vacancy centres (NVC) in diamond have been widely used for near-dc magnetometry. The intrinsic properties of diamonds make them potential candidates for tokamak fusion power diagnostics, where radiation-hard magnetometers will be essential for efficient control. An NVC magnetometer placed in a tokamak will need to operate within a ≥\geq≥ 1 T magnetic field. In this work, we demonstrate fibre-coupled ensemble NVC optically detected magnetic resonance (ODMR) and magnetometry measurements at magnetic fields up to 1.2 T. Sensitivities of approximately 240 to 600 nT/Hz\sqrt{\textrm{Hz}}Hz​ and 110 nT/Hz\sqrt{\textrm{Hz}}Hz​ are achieved in a (10-150) Hz frequency range, for non-degenerate and near-$\langle111111111\rangle$ field alignments respectively.