Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE photonics journal

Superconducting Nanowire Single Photon Detector With Efficiency Over 60% for 2-μm-Wavelength

Hui Zhou, Yiming Pan, Lixing You, Hao Li, Yong Wang, Yan Dong Tang, Heqing Wang, Xiaoyu Liu, Zhen Wang

Published Nov 29, 2019• 11 citations
Publisher

Abstract

We demonstrate superconducting nanowire single photon detector (SNSPD) for the wavelength at around 2 μm. The linewidth of the NbN nanowire is squeezed to 56 nm to increase the intrinsic response efficiencies at longer wavelengths such as 2 μm. Serially connecting avalanche architecture is applied to increase the signal-to-noise ratio (SNR) of the response signal. Further, the optical cavity is optimized to improve the absorption of the device. A silica single-mode fiber is adopted to introduce photons to the SNSPD at a temperature of 2.25 K using a Gifford-McMahon cryocooler. The SNSPD exhibits detection efficiencies of 58%, 67%, and 63% at wavelengths of 1550, 1700, and 2000 nm, respectively, with dark count rate of ~12 kcps, which is reduced to 2 cps when the attached fiber pigtail is all placed inside the 40-K cryostat. The detection efficiency at 2000 nm is 2.5 times greater than that of the best previously developed detector with an efficiency of 25%. Our SNSPD is promising for practical applications in molecular science and earth meteorology.

DOI
10.1109/jphot.2019.2956755

Related papers

Development of practical superconducting nanowire single photon detector system with high detection efficiency

Shigehito Miki, Taro Yamashita, Hirotaka Terai +3 more

We have developed a practical superconducting nanowire single photon detector (SNSPD) system with our superconducting thin films and devices fabrication, optical coupling packaging, and cryogenic technology. The SNSPD devices were fabricated from high-quality niobium nitride (NbN) ultra-thin films that were epitaxially grown on single-crystal MgO substrates, and optical cavity structure were applied for improvement of photo absorption efficiency. The SNSPD system was developed based on a compact Gifford-McMahon (GM) cryocooler, in which SNSPD can operate continuously at temperature of 2.9 K +/- 10 mK with low power consumption without any liquid cryogens. The system detection efficiencies at 1550 nm wavelength (at a 100 Hz dark count rate) were found to be 2.6% for device without optical cavity and 21% for device with optical cavity. The response speed of devices showed maximally 200 MHz with 5 × 5 mm square device, and timing jitter of 100 ps full width at a half maximum (FWHM) was observed.

IEEE International Conference on Space Optical Systems and Applications (ICSOS)•May 1, 2011•0 citations

High efficiency superconducting nanowire single photon detector at wavelength 940 nm

Y. J. Chen, M. Gu, Labao Zhang +2 more

Superconducting nanowire single photon detectors with an optical resonant cavity structure are fabricated directly on the single crystal substrate. In order to enhance the photons absorption of incident light and improve system detection efficiency (SDE) efficiently, the structure of SNSPD was designed and optimized using the finite-difference time-domain analysis for different kinds of substrates. The NbN-SNSPDs fabricated on different substrates are measured and compared. The SDE of NbN-SNSPD on MgO substrate reaches 66 % at the wavelength of 940nm at a dark count rate of 100 cps by illuminating from the back of the device through single mode optical fiber.

International Conference on Infrared, Millimeter, and Terahertz Waves (IRMMW-THz)•Aug 1, 2015•0 citations

50 µm diameter superconducting nanowire single-photon detector with sub-17 ps timing jitter and high efficiency for visible wavelengths (Conference Presentation)

Jin Chang, Iman Esmaeil Zadeh

Superconducting nanowire single photon detectors (SNSPDs) have demonstrated advantages over traditional detectors in many fields [1]. Most fiber-coupled SNSPDs are coupled to single mode fibers, limiting their usability for applications where large surface area detectors are needed, for example fluorescence detection and satellite-based quantum communication [2][3]. Other important requirements for many applications are broadband detection efficiency, and low timing jitter [4]. So far, the increased meander length of multimode detectors, and the therefore increased kinetic inductance and number of imperfections due to film inhomogeneities have limited the timing jitter [5]. Moreover, combining low timing jitter with high detection efficiency and low dark count rate in one device is challenging due to the tradeoffs between different properties of SNSPDs [6]. In this paper, we achieved high efficiency and strong saturation over a broad wavelength range with a low timing jitter of 16.99 ps while maintaining a low dark count rate of < 0.2 Hz for an SNSPD coupled to a 50 µm core multimode fiber. To enhance the broadband absorption from 405 nm to 830 nm, detectors were fabricated on an optimized SiO2 cavity and Aluminum mirror. The geometry of the nanowire was also tuned to reach a good internal saturation of efficiency over the visible/NIR range but also to carry high current to get a large signal. Furthermore, a cryogenic readout amplifier was optimized to improve the signal to noise ratio and thus lead to high time resolution. Our devices can be readily used to enable higher resolution and faster quantum optics, bio-imaging, laser ranging and other optical experiments.

Quantum Optics and Photon Counting•May 13, 2019•0 citations

Superconducting nanowire single photon detector with efficiency over 90% at 2 μm wavelength

Zhen Wan, Jia Huang, Guangzhao Xu +6 more

Abstract We here report a high system detection efficiency (SDE) superconducting single-photon detector (SSPD) at 2 μm wavelength. The device integrates a SiO 2 /Ta 2 O 5 distributed Bragg reflector (DBR) and a sandwich-structured double-layer NbN nanowire to enhance the optical absorption efficiency. A cold development technique is implemented to optimize the superconducting nanowires with sub-40-nm linewidths, thus enhancing the intrinsic detection efficiency (IDE). The fabricated SSPD shows an SDE exceeding 90% at 2 μm wavelength. Moreover, the detector allows an operational working temperature of 2.2 K provided by a compact GM cryo-cooler. This detector delivers excellent performance at the 2 μm wavelength, and its optimized structural design implies promising potential for extending detection toward longer infrared bands. It thus holds value for advancing high-sensitivity quantum technologies, mid-infrared optical communications, and dark matter detection research.

Chinese Physics B•Nov 5, 2025•0 citations

Superconducting microstrip single-photon detector with system detection efficiency over 90% at 1550 nm

Guangzhao Xu, Wei-Jun Zhang, Li-Xing You +9 more

Generally, a superconducting nanowire single-photon detector (SNSPD) is composed of wires with a typical width of ∼ 100 nm . Recent studies have found that superconducting strips with a micrometer-scale width can also detect single photons. Compared with the SNSPD covering the same area, the superconducting microstrip single-photon detector (SMSPD) has smaller kinetic inductance, higher working current, and lower requirements in fabrication accuracy, providing potential applications in the development of ultralarge active area detectors. However, the study of SMSPD is still in its infancy, and the realization of its high-performance and practical use remains an open question. This study demonstrates a NbN SMSPD with a nearly saturated system detection efficiency (SDE) of ∼ 92.2 % at a dark count rate of ∼ 200 cps , a polarization sensitivity of ∼ 1.03 , and a minimum timing jitter of ∼ 48 ps at the telecom wavelength of 1550 nm when coupled with a single-mode fiber and operated at 0.84 K. Furthermore, the detector’s SDE is over 70% when operated at a 2.1 K closed-cycle cryocooler.

arXiv:2101.05407•Photonics Research•Mar 23, 2021•72 citations

NbN Superconducting Nanowire Single-Photon Detector With 90.5% Saturated System Detection Efficiency and 14.7 ps System Jitter at 1550 nm Wavelength

Xingyu Zhang, Weijun Zhang, Hui Zhou +8 more

Superconducting nanowire single-photon detectors (SNSPDs) play a pivotal role in infrared single-photon-detection applications owing to their free-running mode, near-unity detection efficiency, and excellent time resolution. However, conventional niobium nitride- (NbN) SNSPDs often have a trade-off between optimal detection efficiency and time resolution. We herein demonstrate NbN SNSPDs in the combination of high efficiency and time resolution by using the helium-ion-irradiated film of 10 nm and a homemade cryogenic amplifier to improve the signal-to-noise ratio. The proposed 18-μm-diameter device operated at 850 mK shows a saturated system detection efficiency of ∼90.5% at 1550 nm wavelength with a dark count rate below 50 counts per second (cps), and minimum system timing jitter of ∼14.7 ps. Meanwhile, the recovery time is 21.2 ns owing to its lower kinetic inductance. The time-of-flight light detection and ranging with this device was further carried out indoors, which demonstrates a submillimeter (<0.5 mm) depth resolution, as well as good depth and intensity reconstruction of a low-signature object even under the dwell time of 0.5 ms. It indicates that our device has a great advantage and potential in high-time-resolution and weak-signal-detection applications, such as real-time imaging, fluorescence lifetime detection, and remote laser sensing.

IEEE Journal of Selected Topics in Quantum Electronics•Feb 23, 2022•27 citations
We demonstrate superconducting nanowire single photon detector (SNSPD) for the wavelength at around 2 μm. The linewidth of the NbN nanowire is squeezed to 56 nm to increase the intrinsic response efficiencies at longer wavelengths such as 2 μm. Serially connecting avalanche architecture is applied to increase the signal-to-noise ratio (SNR) of the response signal. Further, the optical cavity is optimized to improve the absorption of the device. A silica single-mode fiber is adopted to introduce photons to the SNSPD at a temperature of 2.25 K using a Gifford-McMahon cryocooler. The SNSPD exhibits detection efficiencies of 58%, 67%, and 63% at wavelengths of 1550, 1700, and 2000 nm, respectively, with dark count rate of ~12 kcps, which is reduced to 2 cps when the attached fiber pigtail is all placed inside the 40-K cryostat. The detection efficiency at 2000 nm is 2.5 times greater than that of the best previously developed detector with an efficiency of 25%. Our SNSPD is promising for practical applications in molecular science and earth meteorology.
We have developed a practical superconducting nanowire single photon detector (SNSPD) system with our superconducting thin films and devices fabrication, optical coupling packaging, and cryogenic technology. The SNSPD devices were fabricated from high-quality niobium nitride (NbN) ultra-thin films that were epitaxially grown on single-crystal MgO substrates, and optical cavity structure were applied for improvement of photo absorption efficiency. The SNSPD system was developed based on a compact Gifford-McMahon (GM) cryocooler, in which SNSPD can operate continuously at temperature of 2.9 K +/- 10 mK with low power consumption without any liquid cryogens. The system detection efficiencies at 1550 nm wavelength (at a 100 Hz dark count rate) were found to be 2.6% for device without optical cavity and 21% for device with optical cavity. The response speed of devices showed maximally 200 MHz with 5 × 5 mm square device, and timing jitter of 100 ps full width at a half maximum (FWHM) was observed.
Superconducting nanowire single photon detectors with an optical resonant cavity structure are fabricated directly on the single crystal substrate. In order to enhance the photons absorption of incident light and improve system detection efficiency (SDE) efficiently, the structure of SNSPD was designed and optimized using the finite-difference time-domain analysis for different kinds of substrates. The NbN-SNSPDs fabricated on different substrates are measured and compared. The SDE of NbN-SNSPD on MgO substrate reaches 66 % at the wavelength of 940nm at a dark count rate of 100 cps by illuminating from the back of the device through single mode optical fiber.
Superconducting nanowire single photon detectors (SNSPDs) have demonstrated advantages over traditional detectors in many fields [1]. Most fiber-coupled SNSPDs are coupled to single mode fibers, limiting their usability for applications where large surface area detectors are needed, for example fluorescence detection and satellite-based quantum communication [2][3]. Other important requirements for many applications are broadband detection efficiency, and low timing jitter [4]. So far, the increased meander length of multimode detectors, and the therefore increased kinetic inductance and number of imperfections due to film inhomogeneities have limited the timing jitter [5]. Moreover, combining low timing jitter with high detection efficiency and low dark count rate in one device is challenging due to the tradeoffs between different properties of SNSPDs [6]. In this paper, we achieved high efficiency and strong saturation over a broad wavelength range with a low timing jitter of 16.99 ps while maintaining a low dark count rate of < 0.2 Hz for an SNSPD coupled to a 50 µm core multimode fiber. To enhance the broadband absorption from 405 nm to 830 nm, detectors were fabricated on an optimized SiO2 cavity and Aluminum mirror. The geometry of the nanowire was also tuned to reach a good internal saturation of efficiency over the visible/NIR range but also to carry high current to get a large signal. Furthermore, a cryogenic readout amplifier was optimized to improve the signal to noise ratio and thus lead to high time resolution. Our devices can be readily used to enable higher resolution and faster quantum optics, bio-imaging, laser ranging and other optical experiments.
Abstract We here report a high system detection efficiency (SDE) superconducting single-photon detector (SSPD) at 2 μm wavelength. The device integrates a SiO 2 /Ta 2 O 5 distributed Bragg reflector (DBR) and a sandwich-structured double-layer NbN nanowire to enhance the optical absorption efficiency. A cold development technique is implemented to optimize the superconducting nanowires with sub-40-nm linewidths, thus enhancing the intrinsic detection efficiency (IDE). The fabricated SSPD shows an SDE exceeding 90% at 2 μm wavelength. Moreover, the detector allows an operational working temperature of 2.2 K provided by a compact GM cryo-cooler. This detector delivers excellent performance at the 2 μm wavelength, and its optimized structural design implies promising potential for extending detection toward longer infrared bands. It thus holds value for advancing high-sensitivity quantum technologies, mid-infrared optical communications, and dark matter detection research.
Generally, a superconducting nanowire single-photon detector (SNSPD) is composed of wires with a typical width of ∼ 100 nm . Recent studies have found that superconducting strips with a micrometer-scale width can also detect single photons. Compared with the SNSPD covering the same area, the superconducting microstrip single-photon detector (SMSPD) has smaller kinetic inductance, higher working current, and lower requirements in fabrication accuracy, providing potential applications in the development of ultralarge active area detectors. However, the study of SMSPD is still in its infancy, and the realization of its high-performance and practical use remains an open question. This study demonstrates a NbN SMSPD with a nearly saturated system detection efficiency (SDE) of ∼ 92.2 % at a dark count rate of ∼ 200 cps , a polarization sensitivity of ∼ 1.03 , and a minimum timing jitter of ∼ 48 ps at the telecom wavelength of 1550 nm when coupled with a single-mode fiber and operated at 0.84 K. Furthermore, the detector’s SDE is over 70% when operated at a 2.1 K closed-cycle cryocooler.
Superconducting nanowire single-photon detectors (SNSPDs) play a pivotal role in infrared single-photon-detection applications owing to their free-running mode, near-unity detection efficiency, and excellent time resolution. However, conventional niobium nitride- (NbN) SNSPDs often have a trade-off between optimal detection efficiency and time resolution. We herein demonstrate NbN SNSPDs in the combination of high efficiency and time resolution by using the helium-ion-irradiated film of 10 nm and a homemade cryogenic amplifier to improve the signal-to-noise ratio. The proposed 18-μm-diameter device operated at 850 mK shows a saturated system detection efficiency of ∼90.5% at 1550 nm wavelength with a dark count rate below 50 counts per second (cps), and minimum system timing jitter of ∼14.7 ps. Meanwhile, the recovery time is 21.2 ns owing to its lower kinetic inductance. The time-of-flight light detection and ranging with this device was further carried out indoors, which demonstrates a submillimeter (<0.5 mm) depth resolution, as well as good depth and intensity reconstruction of a low-signature object even under the dwell time of 0.5 ms. It indicates that our device has a great advantage and potential in high-time-resolution and weak-signal-detection applications, such as real-time imaging, fluorescence lifetime detection, and remote laser sensing.