Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

AIP conference proceedings

Simulation of the cut-off wavelength of superconducting single-photon detectors based on WSi thin films for systems for optical space communications

Konstantin M. Moiseev, Д.Д. Васильев, Selbi Hydyrova

Published Jan 1, 2019• 0 citations
Publisher

Abstract

Superconducting single-photon detectors (SNSPD) are receivers in optical systems for space communications and exhibit high quantum efficiency and count rate. The receiver in the optical system of atmospheric communication should provide highly efficient detection of radiation with a wavelength of 1.55 µm. The cut-off wavelength of SNSPD is the maximum wavelength of radiation at which high detection efficiency is maintained and depends on the geometrical parameters of the sensitive element of the detector and the thickness and structure of the thin film of superconducting material parameters. In this work, we simulate the cut-off wavelength depending on the thickness of the superconducting film WxSi1-x and the stoichiometric composition with a nanowire width of 100 nm and a ratio of the bias current to the critical 0.7. It is shown that the largest value of the cut-off wavelength λc = 3.06 µm corresponds to a film thickness of 5 nm and a Si content of 25%. With a film thickness of 7 nm, detection with the required wavelength of 1.55 µm is provided over the entire investigated range of the stoichiometric composition of the film: when the Si content is from 15 to 25%.

DOI
10.1063/1.5133246

Related papers

Superconducting detector of IR single-photons based on thin WSi films

V A Seleznev, A V Divochiy, Yu B Vakhtomin +6 more

We have developed the deposition technology of WSi thin films 4 to 9 nm thick with high temperature values of superconducting transition (T c ~4 K). Based on deposed films there were produced nanostructures with indicative planar sizes ~100 nm, and the research revealed that even on nanoscale the films possess of high critical temperature values of the superconducting transition (T c ~3.3-3.7 K) which certifies high quality and homogeneity of the films created. The first experiments on creating superconducting single-photon detectors showed that the detectors' SDE (system detection efficiency) with increasing bias current (I b ) reaches a constant value of ~30% (for X=1.55 micron) defined by infrared radiation absorption by the superconducting structure. To enhance radiation absorption by the superconductor there were created detectors with cavity structures which demonstrated a practically constant value of quantum efficiency >65% for bias currents I b >0.6-I c . The minimal dark counts level (DC) made 1 s -1 limited with background noise. Hence WSi is the most promising material for creating single-photon detectors with record SDE/DC ratio and noise equivalent power (NEP).

arXiv:1606.09406•Journal of Physics Conference Series•Aug 1, 2016•10 citations

Broadening of hot-spot response spectrum of superconducting NbN nanowire single-photon detector with reduced nitrogen content

D. Henrich, S. Dörner, M. Hofherr +6 more

The spectral detection efficiency and the dark count rate of superconducting nanowire single-photon detectors (SNSPD) have been studied systematically on detectors made from thin NbN films with different chemical compositions. Reduction of the nitrogen content in the 4 nm thick NbN films results in a decrease of the dark count rates more than two orders of magnitude and in a red shift of the cut-off wavelength of the hot-spot SNSPD response. The observed phenomena are explained by an improvement of uniformity of NbN films that has been confirmed by a decrease of resistivity and an increase of the ratio of the measured critical current to the depairing current. The latter factor is considered as the most crucial for both the cut-off wavelength and the dark count rates of SNSPD. Based on our results we propose a set of criteria for material properties to optimize SNSPD in the infrared spectral region.

arXiv:1207.2014•Journal of Applied Physics•Oct 1, 2012•54 citations

Impact of Stoichiometry of MoSi Thin Films for Enhanced Sensitivity of Superconducting Nanowire Single-Photon Detectors

Stefanie Grotowski, Damjan Pecijareski, Hadrien Le Petit Delacour +8 more

We report on the impact of the stoichiometry of superconducting MoSi thin films on the performance of superconducting nanowire single-photon detectors (SNSPDs). Specifically, we investigate the relation between the film parameters critical temperature Tc , sheet resistance Rs and superconductor thickness d and observe a universal scaling behavior. To benchmark the performance of SNSPDs fabricated from films having different stoichiometry, we measure the bias dependent count rate curves, while the detector is illuminated with wavelengths between 780 nm and 1550 nm. The detector performance as a function photon energy for different nanowire widths reveals a linear relation between the detection current and the photon energy. Furthermore, we determine the interfacial thermal boundary conductance $β$ between the superconducting thin film and the substrate, by measuring the return current of the SNSPD and find an increase of $β$ with increasing Mo concentration. The highest sensitivity amongst all compared devices is achieved for Mo$_{0.53}$Si$_{0.47}$, with low Tc (4.1 K) and high Rs (397$Ω$/sq) at a film thickness of 5.4 nm.

cond-mat.supr-conCross-listedarXiv:2605.27179•Materials for Quantum Technology•May 27, 2026•0 citations

Fabricating WSi based superconducting microwire single photon detectors with laser lithography

Maximilian Protte, Varun Verma, Jan Philipp Höpker +3 more

To measure light down to the single photon level, superconducting nanowire single photon detectors (SNSPDs) have become the go-to devices, due to their near unity detection efficiency [1] , high-speed and low noise. An important figure of merit is the internal detection efficiency (IDE). To achieve a saturated IDE in the infrared, wire widths of the order 100 nm are typically required. Nevertheless, recent experiments have shown that functional detectors can be fabricated with wire widths up to 3 µm [2] – [4] . A higher silicon content of the films combined with a smaller film thickness enables wider wires. Increasing the wire width allows for bigger fabrication tolerances which enables the fabrication with optical lithography.

Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe-EQEC)•Jun 21, 2021•0 citations

Superconducting nanowire single-photon detector made of ultrathin γ -Nb 4 N 3 film for mid-infrared wavelengths

Yiming Pan, Hui Zhou, Lu Zhang +6 more

Abstract Superconducting nanowire single-photon detectors (SNSPDs) made of ultrathin δ -NbN films have been widely applied in both visible and infrared wavelengths. For mid-infrared (MIR) wavelengths, SNSPDs made of tungsten silicide films with a lower critical temperature were reported up to 9.9 μ m wavelength. In this study, we demonstrate the potential of NbN-SNSPDs for use in MIR applications. SNSPDs made of γ -Nb 4 N 3 films (critical temperature of 5.1 K for 6.5 nm thick films) instead of δ -NbN films were fabricated. The dependence of the normalized detection efficiency on the bias current indicated a clear trend toward a saturated plateau for wavelengths up to 2145 nm. The calculated cut-off wavelengths indicated the possibility of using γ -Nb 4 N 3 SNSPDs for longer MIR wavelengths.

Superconductor Science and Technology•Apr 15, 2021•12 citations

Design and fabrication of the superconducting single-photon detector operating at the 5 - 10 micrometer wavelength band

Qi Chen, Yue Dai, Li Fei-Yan +11 more

High-performance mid-wave and long-wave infrared single-photon detectors not only have significant research value in the fields of infrared astronomy and defense technology, but are also challenging to be realized in the field of single-photon detection technology. Superconducting nanowire single-photon detectors (SNSPDs) have shown excellent performance in the near-infrared band. However, how to further improve the cutoff wavelength λc is a topic of widespread concern. In this paper, the method for improving λc by applying the regulation of the superconducting disorder is discussed, and a detector with an operating wavelength band of 5 - 10 μm is designed and fabricated. Studies have shown that the multiplication and diffusion behaviors of the quasiparticles always occur during the photon detection events, although the microscopic photodetection mechanism of SNSPD still lacks a perfect theoretical explanation. Therefore, the theoretical analysis mainly considers the influence of the quasiparticles in this paper, and the mathematical formula of the detection cutoff wavelength λc can be obtained based on the phenomenological quasiparticle diffusion model. Furthermore, the disorder-dependent superconducting phase transition temperature Tc, superconducting energy gap <teshuzifu>D, and electron thermalization time τth are also considered, in order to get more precise results. Theoretical analysis suggests that the increase in the sheet resistance Rs, which evaluates the disorder strength, will help to increase λc. For example, when the nanowire width is kept at 30 nm and Rs > 380 Ω/□, it can be deduced that λc is larger than 10 μm. Experimentally, the active area of the device consists of a straight superconducting nanowire with a length of 10 μm and a width of 30 nm, so that it can effectively reduce the probability of the defects on the nanowire and avoid the current crowding effect. We have fabricated a 30 nm-wide Mo0.8Si0.2 mid infrared SNSPD, which has a cutoff wavelength λc no more than 5 μm, the effective strength of the disorder - the film sheet resistance Rs = 248.6 Ω/□. As a comparison, the sheet resistance, which is controlled by the film thickness, is increased to about 320 Ω/□ in this experiment. It is demonstrated that the Mo0.8Si0.2 detector with Rs ~320 Ω/□ can achieve saturated quantum efficiency at a wavelength of 6 μm. Furthermore, 53% quantum efficiency at the wavelength of 10.2 μm can be obtained when the detector works at a bias current of 0.9 ISW (ISW is the superconducting transition current), and it can theoretically reach a maximum value of 92% if the compression of switching current is excluded. Therefore, it can be predicted that the disorder regulation may become another efficient approach for designing high-performance mid-wave and long-wave infrared SNSPDs, in addition to the optimization of the superconducting energy gap and the cross section of superconducting nanowire. However, the continuous increase in the disorder will cause a decrease in both the superconducting phase transition temperature Tc and ISW of the detector from the point of detector fabrication and application. This downward trend is especially pronounced when the nanowire width is ultranarrow, which is not conducive to the signal readout of the detector. Thus, exploring the optimal disorder regulation technology and balancing the relationship between the operating temperature, the signal-to-noise ratio, and the cutoff wavelength will have key scientific and application value for the development of high-performance mid-wave and long-wave infrared SNSPDs.

Acta Physica Sinica•Oct 9, 2022•0 citations
Superconducting single-photon detectors (SNSPD) are receivers in optical systems for space communications and exhibit high quantum efficiency and count rate. The receiver in the optical system of atmospheric communication should provide highly efficient detection of radiation with a wavelength of 1.55 µm. The cut-off wavelength of SNSPD is the maximum wavelength of radiation at which high detection efficiency is maintained and depends on the geometrical parameters of the sensitive element of the detector and the thickness and structure of the thin film of superconducting material parameters. In this work, we simulate the cut-off wavelength depending on the thickness of the superconducting film WxSi1-x and the stoichiometric composition with a nanowire width of 100 nm and a ratio of the bias current to the critical 0.7. It is shown that the largest value of the cut-off wavelength λc = 3.06 µm corresponds to a film thickness of 5 nm and a Si content of 25%. With a film thickness of 7 nm, detection with the required wavelength of 1.55 µm is provided over the entire investigated range of the stoichiometric composition of the film: when the Si content is from 15 to 25%.
We have developed the deposition technology of WSi thin films 4 to 9 nm thick with high temperature values of superconducting transition (T c ~4 K). Based on deposed films there were produced nanostructures with indicative planar sizes ~100 nm, and the research revealed that even on nanoscale the films possess of high critical temperature values of the superconducting transition (T c ~3.3-3.7 K) which certifies high quality and homogeneity of the films created. The first experiments on creating superconducting single-photon detectors showed that the detectors' SDE (system detection efficiency) with increasing bias current (I b ) reaches a constant value of ~30% (for X=1.55 micron) defined by infrared radiation absorption by the superconducting structure. To enhance radiation absorption by the superconductor there were created detectors with cavity structures which demonstrated a practically constant value of quantum efficiency >65% for bias currents I b >0.6-I c . The minimal dark counts level (DC) made 1 s -1 limited with background noise. Hence WSi is the most promising material for creating single-photon detectors with record SDE/DC ratio and noise equivalent power (NEP).
The spectral detection efficiency and the dark count rate of superconducting nanowire single-photon detectors (SNSPD) have been studied systematically on detectors made from thin NbN films with different chemical compositions. Reduction of the nitrogen content in the 4 nm thick NbN films results in a decrease of the dark count rates more than two orders of magnitude and in a red shift of the cut-off wavelength of the hot-spot SNSPD response. The observed phenomena are explained by an improvement of uniformity of NbN films that has been confirmed by a decrease of resistivity and an increase of the ratio of the measured critical current to the depairing current. The latter factor is considered as the most crucial for both the cut-off wavelength and the dark count rates of SNSPD. Based on our results we propose a set of criteria for material properties to optimize SNSPD in the infrared spectral region.
We report on the impact of the stoichiometry of superconducting MoSi thin films on the performance of superconducting nanowire single-photon detectors (SNSPDs). Specifically, we investigate the relation between the film parameters critical temperature Tc , sheet resistance Rs and superconductor thickness d and observe a universal scaling behavior. To benchmark the performance of SNSPDs fabricated from films having different stoichiometry, we measure the bias dependent count rate curves, while the detector is illuminated with wavelengths between 780 nm and 1550 nm. The detector performance as a function photon energy for different nanowire widths reveals a linear relation between the detection current and the photon energy. Furthermore, we determine the interfacial thermal boundary conductance βββ between the superconducting thin film and the substrate, by measuring the return current of the SNSPD and find an increase of βββ with increasing Mo concentration. The highest sensitivity amongst all compared devices is achieved for Mo0.53_{0.53}0.53​Si0.47_{0.47}0.47​, with low Tc (4.1 K) and high Rs (397ΩΩΩ/sq) at a film thickness of 5.4 nm.
To measure light down to the single photon level, superconducting nanowire single photon detectors (SNSPDs) have become the go-to devices, due to their near unity detection efficiency [1] , high-speed and low noise. An important figure of merit is the internal detection efficiency (IDE). To achieve a saturated IDE in the infrared, wire widths of the order 100 nm are typically required. Nevertheless, recent experiments have shown that functional detectors can be fabricated with wire widths up to 3 µm [2] – [4] . A higher silicon content of the films combined with a smaller film thickness enables wider wires. Increasing the wire width allows for bigger fabrication tolerances which enables the fabrication with optical lithography.
Abstract Superconducting nanowire single-photon detectors (SNSPDs) made of ultrathin δ -NbN films have been widely applied in both visible and infrared wavelengths. For mid-infrared (MIR) wavelengths, SNSPDs made of tungsten silicide films with a lower critical temperature were reported up to 9.9 μ m wavelength. In this study, we demonstrate the potential of NbN-SNSPDs for use in MIR applications. SNSPDs made of γ -Nb 4 N 3 films (critical temperature of 5.1 K for 6.5 nm thick films) instead of δ -NbN films were fabricated. The dependence of the normalized detection efficiency on the bias current indicated a clear trend toward a saturated plateau for wavelengths up to 2145 nm. The calculated cut-off wavelengths indicated the possibility of using γ -Nb 4 N 3 SNSPDs for longer MIR wavelengths.
High-performance mid-wave and long-wave infrared single-photon detectors not only have significant research value in the fields of infrared astronomy and defense technology, but are also challenging to be realized in the field of single-photon detection technology. Superconducting nanowire single-photon detectors (SNSPDs) have shown excellent performance in the near-infrared band. However, how to further improve the cutoff wavelength λc is a topic of widespread concern. In this paper, the method for improving λc by applying the regulation of the superconducting disorder is discussed, and a detector with an operating wavelength band of 5 - 10 μm is designed and fabricated. Studies have shown that the multiplication and diffusion behaviors of the quasiparticles always occur during the photon detection events, although the microscopic photodetection mechanism of SNSPD still lacks a perfect theoretical explanation. Therefore, the theoretical analysis mainly considers the influence of the quasiparticles in this paper, and the mathematical formula of the detection cutoff wavelength λc can be obtained based on the phenomenological quasiparticle diffusion model. Furthermore, the disorder-dependent superconducting phase transition temperature Tc, superconducting energy gap <teshuzifu>D, and electron thermalization time τth are also considered, in order to get more precise results. Theoretical analysis suggests that the increase in the sheet resistance Rs, which evaluates the disorder strength, will help to increase λc. For example, when the nanowire width is kept at 30 nm and Rs > 380 Ω/□, it can be deduced that λc is larger than 10 μm. Experimentally, the active area of the device consists of a straight superconducting nanowire with a length of 10 μm and a width of 30 nm, so that it can effectively reduce the probability of the defects on the nanowire and avoid the current crowding effect. We have fabricated a 30 nm-wide Mo0.8Si0.2 mid infrared SNSPD, which has a cutoff wavelength λc no more than 5 μm, the effective strength of the disorder - the film sheet resistance Rs = 248.6 Ω/□. As a comparison, the sheet resistance, which is controlled by the film thickness, is increased to about 320 Ω/□ in this experiment. It is demonstrated that the Mo0.8Si0.2 detector with Rs ~320 Ω/□ can achieve saturated quantum efficiency at a wavelength of 6 μm. Furthermore, 53% quantum efficiency at the wavelength of 10.2 μm can be obtained when the detector works at a bias current of 0.9 ISW (ISW is the superconducting transition current), and it can theoretically reach a maximum value of 92% if the compression of switching current is excluded. Therefore, it can be predicted that the disorder regulation may become another efficient approach for designing high-performance mid-wave and long-wave infrared SNSPDs, in addition to the optimization of the superconducting energy gap and the cross section of superconducting nanowire. However, the continuous increase in the disorder will cause a decrease in both the superconducting phase transition temperature Tc and ISW of the detector from the point of detector fabrication and application. This downward trend is especially pronounced when the nanowire width is ultranarrow, which is not conducive to the signal readout of the detector. Thus, exploring the optimal disorder regulation technology and balancing the relationship between the operating temperature, the signal-to-noise ratio, and the cutoff wavelength will have key scientific and application value for the development of high-performance mid-wave and long-wave infrared SNSPDs.