Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEICE Technical Report; IEICE Tech. Rep.

Fabrication of three-dimensional superconducting tunnel junctions

Go Fujii, Masahiro Ukibe, Shigetomo Shiki, M. Ohkubo

Published Oct 8, 2014• 0 citations
OpenAlex

Related papers

Design and Fabrication of On-Chip Coil Integrated Superconducting Tunnel Junction

Toru Taino, Kazuro Kikuchi, Hirosi Nakagawa +8 more

•Jan 1, 2003•0 citations

Superconducting tunnel junction fabrication on three-dimensional topography based on direct laser writing

Samuli Heiskanen, Ilari J. Maasilta

Superconducting junctions are widely used in a multitude of applications ranging from quantum information science and sensing to solid-state cooling. Traditionally, such devices must be fabricated on flat substrates using standard lithographic techniques. In this study, we demonstrate a highly versatile method that allows for superconducting junctions to be fabricated on a more complex topography. It is based on maskless direct laser writing and two-photon lithography, which allows writing in 3D space. We show that high-quality normal metal–insulator–superconductor tunnel junctions can be fabricated on top of a 20-μm-tall three-dimensional topography. Combined with conformal resist coating methods, this technique could allow sub-micron device fabrication on almost any type of topography in the future.

arXiv:2009.09749•Applied Physics Letters•Dec 7, 2020•3 citations

Fabrication and electrical measurement of ultra-small superconducting junctions

林冠宇, Kuan-Yu Lin

•Jan 1, 2012•0 citations

Enabling scalable fabrication of superconducting quantum technologies

Satyavolu S. Papa Rao

SPIE Quantum Information Science, Sensing, and Computation•May 30, 2025•0 citations

Fabrication of High-Quality Niobium Superconducting Tunnel Junctions

Qinyin Xu, Chunhai Cao, Mengyue Li +6 more

For high-quality superconducting tunnel junctions (STJs), it is necessary to reduce leakage current as much as possible. We describe the fabrication of niobium STJs using the selective niobium (Nb) etching process and various ways to minimize the leakage current. The experiment shows that the leakage current mainly comes from shorts in the tunnel barrier layer rather than those around the junction edges. Through systematic analysis of the thin film stress, surface morphology and modified junction structures, we fabricate high-quality Nb STJs with a gap voltage of 2.8 mV and a leakage current at 1 mV as low as 8.1% and 0.023% at 4.2 K and 0.3 K, respectively.

Chinese Physics Letters•Aug 1, 2011•3 citations

Character and fabrication of Al/Al2O3/Al tunnel junctions for qubit application

DanDan Shen, Ran Zhu, Weiwei Xu +5 more

The superconductive Josephson junction is the key device for superconducting quantum computation. We have fabricated Al/Al2O3/Al tunnel junctions using a double angle evaporation method based on a suspended shadow mask. The Al2O3 junction barrier has been formed by introducing pure oxygen into the chamber during the fabrication process. We have adjusted exposure conditions by changing either the oxygen pressure or the oxidizing time during the formation of tunnel barriers to control the critical current density J c and the junction specific resistance R c . Measurements of the leakage in Al/Al2O3/Al tunnel junctions show that the devices are suitable for qubit applications.

Chinese Science Bulletin•Jan 20, 2012•19 citations
Superconducting junctions are widely used in a multitude of applications ranging from quantum information science and sensing to solid-state cooling. Traditionally, such devices must be fabricated on flat substrates using standard lithographic techniques. In this study, we demonstrate a highly versatile method that allows for superconducting junctions to be fabricated on a more complex topography. It is based on maskless direct laser writing and two-photon lithography, which allows writing in 3D space. We show that high-quality normal metal–insulator–superconductor tunnel junctions can be fabricated on top of a 20-μm-tall three-dimensional topography. Combined with conformal resist coating methods, this technique could allow sub-micron device fabrication on almost any type of topography in the future.
For high-quality superconducting tunnel junctions (STJs), it is necessary to reduce leakage current as much as possible. We describe the fabrication of niobium STJs using the selective niobium (Nb) etching process and various ways to minimize the leakage current. The experiment shows that the leakage current mainly comes from shorts in the tunnel barrier layer rather than those around the junction edges. Through systematic analysis of the thin film stress, surface morphology and modified junction structures, we fabricate high-quality Nb STJs with a gap voltage of 2.8 mV and a leakage current at 1 mV as low as 8.1% and 0.023% at 4.2 K and 0.3 K, respectively.
The superconductive Josephson junction is the key device for superconducting quantum computation. We have fabricated Al/Al2O3/Al tunnel junctions using a double angle evaporation method based on a suspended shadow mask. The Al2O3 junction barrier has been formed by introducing pure oxygen into the chamber during the fabrication process. We have adjusted exposure conditions by changing either the oxygen pressure or the oxidizing time during the formation of tunnel barriers to control the critical current density J c and the junction specific resistance R c . Measurements of the leakage in Al/Al2O3/Al tunnel junctions show that the devices are suitable for qubit applications.