Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

An atom interferometer for measuring horizontal accelerations

Jimmy Stammers

Published Nov 1, 2018• 6 citations
Publisher

Abstract

Matter-wave interferometry has enabled high precision measurements of inertial forces such as gravity and the Coriolis force. This is facilitated by the long-term stability of the physical properties of atoms and lasers. Recent experiments have demonstrated the operation of portable, robust sensors using atom interferometry. This has potential uses in the context of inertial navigation, where conventional devices suffer from long-term drifts due to bias instability. Furthermore, determining position via dead reckoning requires minimisation of dead time between measurements. This thesis presents the development of an atom interferometer for measuring horizontal accelerations. In this configuration, gravity induces motion across the laser wavefront, which constrains the tolerable level of wavefront distortions. Effective control of the experiment allows the interferometer to be operated at a rate of 4 Hz. A cold ensemble of 10^6 atoms in the same internal state is prepared in 150 ms. The interferometer operates using a sequence of three laser pulses separated by T= 25 ms to achieve sensitivity to horizontal accelerations. Combining this with a classical accelerometer provides a method of correcting for vibration-induced noise, as well as determining the interferometer fringe order. After an integration time of 40 s, the sensitivity to horizontal accelerations is better than 3^-6 m s^-2. Effects which limit this sensitivity are discussed.

DOI
10.25560/68008

Related papers

Development of compact cold-atom sensors for inertial navigation

Baptiste Battelier, B. Barrett, Lauriane Fouché +7 more

Inertial sensors based on cold atom interferometry exhibit many interesting features for applications related to inertial navigation, particularly in terms of sensitivity and long-term stability. However, at present the typical atom interferometer is still very much an experiment—consisting of a bulky, static apparatus with a limited dynamic range and high sensitivity to environmental effects. To be compliant with mobile applications further development is needed. In this work, we present a compact and mobile experiment, which we recently used to achieve the first inertial measurements with an atomic accelerometer onboard an aircraft. By integrating classical inertial sensors into our apparatus, we are able to operate the atomic sensor well beyond its standard operating range, corresponding to half of an interference fringe. We report atom-based acceleration measurements along both the horizontal and vertical axes of the aircraft with one-shot sensitivities of 2.3 × 10−4 g over a range of ∼ 0.1 g. The same technology can be used to develop cold-atom gyroscopes, which could surpass the best optical gyroscopes in terms of long-term sensitivity. Our apparatus was also designed to study multi-axis atom interferometry with the goal of realizing a full inertial measurement unit comprised of the three axes of acceleration and rotation. Finally, we present a compact and tunable laser system, which constitutes an essential part of any cold-atom-based sensor. The architecture of the laser is based on phase modulating a single fiber-optic laser diode, and can be tuned over a range of 1 GHz in less than 200 μs.

arXiv:1605.02454•Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Apr 29, 2016•84 citations

Building a sensitive atom interferometer for navigation

Xiaxi Cheng

The presented thesis describes the setting up of an inertial sensitive atom interferometer for navigation using Rubidium 87 atoms, which is able to perform horizontal acceleration measurement. An ultra-high vacuum interferometer chamber is designed and built. The cold atoms are prepared in a compact 2D MOT setup and loaded into the main MOT. These atoms are then cooled down to few K and prepared in a magnetically insensitive ground state using a sequence of optical and microwave pulses, after which atoms are selected in a narrow band of the velocity. A three-pulse Mach-Zehnder ( pi/2 -pi-pi/2) interferometer using stimulated Raman transitions is used to measure the horizontal acceleration. To improve the sensitivity to acceleration, the fringe contrast of the interferometer requires to be optimised. By investigating the intensity profile of the Raman beams using atoms, a procedure is developed to operate the interferometer in an improved condition, which is able to enhance the fringe contrast by a factor of 3. This procedure improves the shot-to-shot sensitivity of the interferometer below 5 um/s^2. In addition, the atom interferometer is compared with a classical state-of-the-art accelerometer.

•Sep 1, 2019•2 citations

Detecting inertial effects with airborne matter-wave interferometry

Rémi Geiger, Vincent Ménoret, Guillaume Stern +10 more

Inertial sensors relying on atom interferometry offer a breakthrough advance in a variety of applications, such as inertial navigation, gravimetry or ground- and space-based tests of fundamental physics. These instruments require a quiet environment to reach their performance and using them outside the laboratory remains a challenge. Here we report the first operation of an airborne matter-wave accelerometer set up aboard a 0g plane and operating during the standard gravity (1g) and microgravity (0g) phases of the flight. At 1g, the sensor can detect inertial effects more than 300 times weaker than the typical acceleration fluctuations of the aircraft. We describe the improvement of the interferometer sensitivity in 0g, which reaches 2 x 10-4 ms-2 / √Hz with our current setup. We finally discuss the extension of our method to airborne and spaceborne tests of the Universality of free fall with matter waves. Inertial sensors using atom interferometry have applications in geophysics, navigation- and space-based tests of fundamental physics. Here, the first operation of an atom accelerometer during parabolic flights is reported, demonstrating high-resolution measurements at both 1g and 0g.

arXiv:1109.5905•Nature Communications•Sep 20, 2011•411 citations

Inertial noise post-correction in atom interferometers measuring the local gravitational acceleration

L. Richardson

Exploiting the quantum nature of atoms through the use of matter-wave interferometry has lead to the development of devices sensitive to, among other things, the local gravitational acceleration. Measurements of the gravitational acceleration have applications ranging from detection of subterranean density di erences to observation of general relativistic e ects. Light-pulse atom interferometers provide an absolute measurement of the gravitational acceleration with a sensitivity competitive and even surpassing the performance of classical sensors. The advantages of atom interferometers as inertial measurement devices have lead to e orts in increasing sensitivity and decreasing the physical dimensions of the measurement head, allowing them to be more transportable for eld use applications. With increasing sensitivity, it becomes more critical to address the noise source limitations a ecting the measurement, speci cally the in uence of ground motion on measurements. Vibrations coupling into the inertial reference add a time varying phase shift uncommon to the paths of the interferometer. This limitation is especially pertinent to transportable atom gravimeters measuring in the eld where inertial noise is typically far higher than in relatively quiet laboratory environments. Within this work, implementation and demonstration of inertial noise post-correction in an atom interferometer is shown within low inertial noise environments and simulated strong motion environments. For a high pulse separation time atom interferometer (T = 78 ms) post-correction yielded an increase in the short term stability from 4.4 x 10 ̄6 m/s2/√Hz to 9.2 x 10 ̄7 m/s2/√Hz. This method was reproduced with a di erent motion sensor to perform post-correction in a high motion environment, generated by introducing additional movement onto the inertial reference. By performing post-correction in the high motion environment, we were able to show an increase of short term stability of γ = 73.8. Current limitations to the post-correction resulted from self noise resolution limitations and spectral resolutions limitations. Beyond corrections with commercially available sensors, this work demonstrates the rst post-correction with a next generation compact optomechanical sensor. This optomechanical sensor is formed from monolithic fused silica capable of sensitively measuring accelerations of a harmonic oscillator test mass, which can be read-out optically. This novel motion sensor has the advantage to any previously shown sensor used for post-correction in the capacity that it is vacuum compatible, insensitive to magnetic elds and has the potential to be implemented directly into the inertial reference. In this work, inertial noise post-correction in a simulated high motion environment is shown, correcting from a short term stability of 8 x 10 ̄3 m/s2/√Hz to 5 x 10 ̄4 m/s2/√Hz. Post-correction was limited by the parasitic cavities within the ber required for optical read-out of the harmonic oscillator displacement and intensity noise uctuations of the source laser. The results shown within this work are congruent with previous works on atom chip gravimeters, both of which help move towards portable hand-held gravimeter measurement heads capable of sensitive inertial measurement.

•Jan 1, 2019•10 citations

Atom interferometers for navigation

Joseph Thom

We are developing an atom interferometer that measures horizontal accelerations to form a component of a quantum inertial measurement unit. Benefitting from the inherent stability of atom interferometry, this points to a navigation system that offers long-term accuracy without recourse to GPS. To aid compactness and transportability, the sub-components of the quantum sensor are mounted in a 19-inch rack. This includes an optical system of two titanium-sapphire lasers that delivers all of the optical pulses required to operate a highly sensitive atom interferometer using 87Rb atoms. Active compensation systems that allow operation of the quantum sensor in the noisy environment of a moving vehicle are described. Finally, we give an account of recent field trials on a variety of test platforms.

Optical and Quantum Sensing and Precision Metrology II•Mar 8, 2023•0 citations

Versatile optical potentials and their applications in atom interferometry

Knut Stolzenberg

Inertial navigation systems are vital for modern society, be it on airplanes or in the context of autonomous mobility. On the other hand atom interferometers are exquisite measurement devices for inertia in fundamental physics and field applications, but are mostly limited to measuring one inertial observable. By utilizing time averaged optical potentials, the ultra-cold atomic ensemble input to the interferometer can be prepared in nearly arbitrary fashion. This results in a boost of preparation speed and number of atoms in the interferometer by increasing the size of the trap to match the size of the pre-cooled ensemble for optimal loading. Successive fast reduction of the extend of the trap leads to optimal evaporation efficiency and leads to increased sensitivity of the device, due to reduced cycle time of the experiment and increased atom number. Beyond this, the technique allows for new sensor geometries via the creation of multiple single wells, allowing for differential atom interferometry with numerous simultaneous interferometers. In this thesis, the first matter-wave analogue of a classical accelerometer array is implemented via the creation of a 3 × 3 array of Bose-Einstein condensates, consisting of 3 × 105 atoms and spanning a total area of 1.6 mm2 . Successive manipulation of the matter-waves with atom optics, coherently addressing the momentum states of the ensembles, allows for splitting, redirecting and readout pulses, realizing Mach-Zehnder type atom interferometers. Correlation of the nine 1D-acceleration measurements output by the interferometers yields measurements of linear acceleration, Euler- and centrifugal acceleration. The estimated sensitivity limits per shot are 6 × 10−5m s−2 for linear acceleration, 0.19 rad s − 2 for rotational acceleration and 203 mrad s−1 for rotation rate and are mainly limited due to the short free fall time of the ensembles, constrained by the atom optics light field. The correlation also allowed to determine the rotation center, being close to the retro reflection mirror of the atom optics light field. Crucial for the realization of this measurement was the implementation of time averaged potentials as stated above, facilitated through two 2D acousto-optical deflectors and a software defined radio, allowing for generating the required RF-signals. The techniques to simultaneously load and evaporate multiple ensembles into distinct traps from a single cloud of cold atoms and subsequently enlarge the spacing between the ensembles with adiabatic transport ramps are of highest interest for e.g. the Very Long Baseline Atom Interferometer facility in Hannover. Due to the correlated outputs systematic errors, such as wave front abberations, can be nullified. Furthermore the scheme can be extended to 3D matter-wave arrays, fulfilling all requirements necessary for an autonomous inertial measurement unit.

•Jan 1, 2026•0 citations
Matter-wave interferometry has enabled high precision measurements of inertial forces such as gravity and the Coriolis force. This is facilitated by the long-term stability of the physical properties of atoms and lasers. Recent experiments have demonstrated the operation of portable, robust sensors using atom interferometry. This has potential uses in the context of inertial navigation, where conventional devices suffer from long-term drifts due to bias instability. Furthermore, determining position via dead reckoning requires minimisation of dead time between measurements. This thesis presents the development of an atom interferometer for measuring horizontal accelerations. In this configuration, gravity induces motion across the laser wavefront, which constrains the tolerable level of wavefront distortions. Effective control of the experiment allows the interferometer to be operated at a rate of 4 Hz. A cold ensemble of 10^6 atoms in the same internal state is prepared in 150 ms. The interferometer operates using a sequence of three laser pulses separated by T= 25 ms to achieve sensitivity to horizontal accelerations. Combining this with a classical accelerometer provides a method of correcting for vibration-induced noise, as well as determining the interferometer fringe order. After an integration time of 40 s, the sensitivity to horizontal accelerations is better than 3^-6 m s^-2. Effects which limit this sensitivity are discussed.
Inertial sensors based on cold atom interferometry exhibit many interesting features for applications related to inertial navigation, particularly in terms of sensitivity and long-term stability. However, at present the typical atom interferometer is still very much an experiment—consisting of a bulky, static apparatus with a limited dynamic range and high sensitivity to environmental effects. To be compliant with mobile applications further development is needed. In this work, we present a compact and mobile experiment, which we recently used to achieve the first inertial measurements with an atomic accelerometer onboard an aircraft. By integrating classical inertial sensors into our apparatus, we are able to operate the atomic sensor well beyond its standard operating range, corresponding to half of an interference fringe. We report atom-based acceleration measurements along both the horizontal and vertical axes of the aircraft with one-shot sensitivities of 2.3 × 10−4 g over a range of ∼ 0.1 g. The same technology can be used to develop cold-atom gyroscopes, which could surpass the best optical gyroscopes in terms of long-term sensitivity. Our apparatus was also designed to study multi-axis atom interferometry with the goal of realizing a full inertial measurement unit comprised of the three axes of acceleration and rotation. Finally, we present a compact and tunable laser system, which constitutes an essential part of any cold-atom-based sensor. The architecture of the laser is based on phase modulating a single fiber-optic laser diode, and can be tuned over a range of 1 GHz in less than 200 μs.
The presented thesis describes the setting up of an inertial sensitive atom interferometer for navigation using Rubidium 87 atoms, which is able to perform horizontal acceleration measurement. An ultra-high vacuum interferometer chamber is designed and built. The cold atoms are prepared in a compact 2D MOT setup and loaded into the main MOT. These atoms are then cooled down to few K and prepared in a magnetically insensitive ground state using a sequence of optical and microwave pulses, after which atoms are selected in a narrow band of the velocity. A three-pulse Mach-Zehnder ( pi/2 -pi-pi/2) interferometer using stimulated Raman transitions is used to measure the horizontal acceleration. To improve the sensitivity to acceleration, the fringe contrast of the interferometer requires to be optimised. By investigating the intensity profile of the Raman beams using atoms, a procedure is developed to operate the interferometer in an improved condition, which is able to enhance the fringe contrast by a factor of 3. This procedure improves the shot-to-shot sensitivity of the interferometer below 5 um/s^2. In addition, the atom interferometer is compared with a classical state-of-the-art accelerometer.
Inertial sensors relying on atom interferometry offer a breakthrough advance in a variety of applications, such as inertial navigation, gravimetry or ground- and space-based tests of fundamental physics. These instruments require a quiet environment to reach their performance and using them outside the laboratory remains a challenge. Here we report the first operation of an airborne matter-wave accelerometer set up aboard a 0g plane and operating during the standard gravity (1g) and microgravity (0g) phases of the flight. At 1g, the sensor can detect inertial effects more than 300 times weaker than the typical acceleration fluctuations of the aircraft. We describe the improvement of the interferometer sensitivity in 0g, which reaches 2 x 10-4 ms-2 / √Hz with our current setup. We finally discuss the extension of our method to airborne and spaceborne tests of the Universality of free fall with matter waves. Inertial sensors using atom interferometry have applications in geophysics, navigation- and space-based tests of fundamental physics. Here, the first operation of an atom accelerometer during parabolic flights is reported, demonstrating high-resolution measurements at both 1g and 0g.
Exploiting the quantum nature of atoms through the use of matter-wave interferometry has lead to the development of devices sensitive to, among other things, the local gravitational acceleration. Measurements of the gravitational acceleration have applications ranging from detection of subterranean density di erences to observation of general relativistic e ects. Light-pulse atom interferometers provide an absolute measurement of the gravitational acceleration with a sensitivity competitive and even surpassing the performance of classical sensors. The advantages of atom interferometers as inertial measurement devices have lead to e orts in increasing sensitivity and decreasing the physical dimensions of the measurement head, allowing them to be more transportable for eld use applications. With increasing sensitivity, it becomes more critical to address the noise source limitations a ecting the measurement, speci cally the in uence of ground motion on measurements. Vibrations coupling into the inertial reference add a time varying phase shift uncommon to the paths of the interferometer. This limitation is especially pertinent to transportable atom gravimeters measuring in the eld where inertial noise is typically far higher than in relatively quiet laboratory environments. Within this work, implementation and demonstration of inertial noise post-correction in an atom interferometer is shown within low inertial noise environments and simulated strong motion environments. For a high pulse separation time atom interferometer (T = 78 ms) post-correction yielded an increase in the short term stability from 4.4 x 10 ̄6 m/s2/√Hz to 9.2 x 10 ̄7 m/s2/√Hz. This method was reproduced with a di erent motion sensor to perform post-correction in a high motion environment, generated by introducing additional movement onto the inertial reference. By performing post-correction in the high motion environment, we were able to show an increase of short term stability of γ = 73.8. Current limitations to the post-correction resulted from self noise resolution limitations and spectral resolutions limitations. Beyond corrections with commercially available sensors, this work demonstrates the rst post-correction with a next generation compact optomechanical sensor. This optomechanical sensor is formed from monolithic fused silica capable of sensitively measuring accelerations of a harmonic oscillator test mass, which can be read-out optically. This novel motion sensor has the advantage to any previously shown sensor used for post-correction in the capacity that it is vacuum compatible, insensitive to magnetic elds and has the potential to be implemented directly into the inertial reference. In this work, inertial noise post-correction in a simulated high motion environment is shown, correcting from a short term stability of 8 x 10 ̄3 m/s2/√Hz to 5 x 10 ̄4 m/s2/√Hz. Post-correction was limited by the parasitic cavities within the ber required for optical read-out of the harmonic oscillator displacement and intensity noise uctuations of the source laser. The results shown within this work are congruent with previous works on atom chip gravimeters, both of which help move towards portable hand-held gravimeter measurement heads capable of sensitive inertial measurement.
We are developing an atom interferometer that measures horizontal accelerations to form a component of a quantum inertial measurement unit. Benefitting from the inherent stability of atom interferometry, this points to a navigation system that offers long-term accuracy without recourse to GPS. To aid compactness and transportability, the sub-components of the quantum sensor are mounted in a 19-inch rack. This includes an optical system of two titanium-sapphire lasers that delivers all of the optical pulses required to operate a highly sensitive atom interferometer using 87Rb atoms. Active compensation systems that allow operation of the quantum sensor in the noisy environment of a moving vehicle are described. Finally, we give an account of recent field trials on a variety of test platforms.
Inertial navigation systems are vital for modern society, be it on airplanes or in the context of autonomous mobility. On the other hand atom interferometers are exquisite measurement devices for inertia in fundamental physics and field applications, but are mostly limited to measuring one inertial observable. By utilizing time averaged optical potentials, the ultra-cold atomic ensemble input to the interferometer can be prepared in nearly arbitrary fashion. This results in a boost of preparation speed and number of atoms in the interferometer by increasing the size of the trap to match the size of the pre-cooled ensemble for optimal loading. Successive fast reduction of the extend of the trap leads to optimal evaporation efficiency and leads to increased sensitivity of the device, due to reduced cycle time of the experiment and increased atom number. Beyond this, the technique allows for new sensor geometries via the creation of multiple single wells, allowing for differential atom interferometry with numerous simultaneous interferometers. In this thesis, the first matter-wave analogue of a classical accelerometer array is implemented via the creation of a 3 × 3 array of Bose-Einstein condensates, consisting of 3 × 105 atoms and spanning a total area of 1.6 mm2 . Successive manipulation of the matter-waves with atom optics, coherently addressing the momentum states of the ensembles, allows for splitting, redirecting and readout pulses, realizing Mach-Zehnder type atom interferometers. Correlation of the nine 1D-acceleration measurements output by the interferometers yields measurements of linear acceleration, Euler- and centrifugal acceleration. The estimated sensitivity limits per shot are 6 × 10−5m s−2 for linear acceleration, 0.19 rad s − 2 for rotational acceleration and 203 mrad s−1 for rotation rate and are mainly limited due to the short free fall time of the ensembles, constrained by the atom optics light field. The correlation also allowed to determine the rotation center, being close to the retro reflection mirror of the atom optics light field. Crucial for the realization of this measurement was the implementation of time averaged potentials as stated above, facilitated through two 2D acousto-optical deflectors and a software defined radio, allowing for generating the required RF-signals. The techniques to simultaneously load and evaporate multiple ensembles into distinct traps from a single cloud of cold atoms and subsequently enlarge the spacing between the ensembles with adiabatic transport ramps are of highest interest for e.g. the Very Long Baseline Atom Interferometer facility in Hannover. Due to the correlated outputs systematic errors, such as wave front abberations, can be nullified. Furthermore the scheme can be extended to 3D matter-wave arrays, fulfilling all requirements necessary for an autonomous inertial measurement unit.