Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Current Science

Cryogenic Measurement Set-Up for Characterization of Superconducting Nano Structures for Single-Photon Detection Applications

Manju Singh, Rishu Chaujar B, Rajib Kumar Rakshit

Published Sep 1, 2018• 5 citations
Publisher

Abstract

We discuss the design and development of a cryogenic set-up down to ~1.8 K for carrying out measurements on superconducting nanowire single-photon detectors.The set-up consists of two separate low-temperature inserts, one for electrical characterization and the other for optical measurements and characterization of single-photon detectors.A sample holder with necessary arrangements for precise alignment of laser light with the active area of the device to enhance optical coupling efficiency has been designed for the optical probe.The invar alloy has been used for the sample holder to ensure that the alignment is not disturbed at low temperature.Single-mode fibres due to their high transmission rate, minimum attenuation and least distortion have been used to shine light on the samples.The sample holder with 20-pin LCC socket and matching chip carrier provides convenient and fast sample mounting in the electrical insert.Mumetal has been employed to cover the sample space in both the inserts in order to attenuate any electromagnetic interference.Temperature stability with the passage of time has been monitored.It has been found that variation in temperature is less than 10 mK at the lowest operating temperature.Another important advantage of the system is its low enough liquid helium loss rate (~100 ml/h) with all inserts, which allows uninterrupted measurements for several days without any refilling of liquid helium.

DOI
10.18520/cs/v115/i6/1085-1090

Related papers

Packaging and Characterization of NbN Superconducting Nanowire Single Photon Detectors

Jean-Luc Orgiazzi

Superconducting nanowire single-photon detectors (SNSPDs) are nanodevices usually made from thin niobium nitride (NbN) films. Operated at liquid helium temperature, they can exhibit high detection efficiency with low dark-counts associated with a fast response time and a low timing jitter. Covering a broad detection range from ultraviolet to mid-infrared, SNSPDs are a very attractive alternative to silicon or gallium arsenide based semiconductor detectors for fiber based telecommunication when single-photon sensitivity and high counting rates are necessary. \nEfficient packaging and fiber coupling of a SNSPD is in itself a real challenge and is often a limiting factor in reaching high system quantum efficiency. Our approach makes use of a controlled expansion alloy which has been adequately heat treated to enhance its characteristics for cryogenic operation. This insures the integrity of the optical coupling at cryogenic temperatures while done at room temperature. It also provides a good attenuation for electromagnetic interference due to the high relative permeability of the nickel-iron alloy. The small form factor of this pigtailed optical fiber package makes it versatile and could be easily integrated with a commercial cryogen-free system or simply dipped into a standard helium transport Dewar. We report on our theoretical and experimental methodology to evaluate the optical coupling quality and present the optoelectronic characterization of two devices packaged in this way. Electrical simulation is studied to understand the speed limitation factor inherent to these devices and preliminary speed and jitter measurements are reported.

•May 22, 2009•0 citations

Nano-optical studies of superconducting nanowire devices for single-photon detection

Robert M. Heath

Superconducting nanowire single photon detectors (SNSPDs) are a rapidly maturing detector technology that offer superior performance relative to competing infrared photon counting technologies. The original experimental work presented here explores three novel methods of improving and analysing detector characteristics, employing low-temperature piezoelectric motors at temperatures below 4 K in a closed-cycle cryostat. Utilizing the low-temperature piezoelectric nanopositioners in tandem with a miniature confocal microscope, this work specifically shows a spatially-separable parallel-wire SNSPD demonstrating one- and two-pixel photon discrimination, with the detector responding more quickly when triggering two pixels. The work demonstrates nanoantenna-coupled SNSPDs, which are simulated, designed, and tested using the same nano-optical setup. In these an increased local absorption into the nanowire is seen at the antennas' resonant wavelengths, enhancing the efficiency of the detector by up to 130 %. Finally, a modified optical setup using a distributed Bragg reflector fibre in place of the microscope to form a tunable cavity around two configurations of SNSPD is demonstrated, improving absorption of the incident light into the nanowire across the whole active area. For these, enhancement in the system detection efficiency of up to 40 % is seen.

•Jan 1, 2015•1 citation

Coupling light to superconductive photon counters

Xiaolong Hu

Superconductive nanowire single-photon detectors (SNSPDs) are an emerging, ultrasensitive photon counting technology which may enable fiber-based, long-haul quantum key distribution.Our group has successfully developed a robust process to fabricate SNSPDs, and has demonstrated device-detection-efficiency above 50% at near infrared wavelengths [1].However, one remaining challenge must be takenefficiently coupling light into the detector.This step is difficult because of the small active area of the SNSPD and its low temperature operation.In this thesis, I have designed two experimental setups to couple the light from fiber to the detector at a cryogenic temperature of 4 K: one is for immersion device-testing in a dewar; another is for packaging the detector inside a cryocooler.In addition, I have designed and fabricated SNSPDs suitable for the coupling with single-mode fiber, based on my theoretical calculation of the system detection-efficiency.Some important parameters to characterize the detectors such as system-detection-efficiency, dark-count rate, and counting rate vs. optical input power have been measured.

•Jan 1, 2008•1 citation

Robust Packaging Technique and Characterization of Fiber-Pigtailed Superconducting NbN Nanowire Single Photon Detectors

Jean-Luc Orgiazzi, A. Hamed Majedi

Efficient packaging and fiber coupling of a superconducting niobium nitride nanowire single photon detector is in itself a real challenge and is often a limiting factor to reach a high system quantum efficiency. Our approach makes use of a controlled expansion alloy, Carpenter Invar 36, that has been adequately heat treated to enhance its characteristics for cryogenic operation. This insures the integrity of the optical coupling done at room temperature while providing a good attenuation for electromagnetic interference due to the high relative permeability of this nickel-iron alloy. The small form factor of this optical fiber pigtailed package makes it versatile and could be easily integrated with a commercial cryogen-free system or simply dipped into a standard helium transport Dewar. We report on our experimental methodology to evaluate the optical coupling quality and present the optoelectronic characterization of two devices packaged in this way.

IEEE Transactions on Applied Superconductivity•Jun 1, 2009•9 citations

Development of practical superconducting nanowire single photon detector system with high detection efficiency

Shigehito Miki, Taro Yamashita, Hirotaka Terai +3 more

We have developed a practical superconducting nanowire single photon detector (SNSPD) system with our superconducting thin films and devices fabrication, optical coupling packaging, and cryogenic technology. The SNSPD devices were fabricated from high-quality niobium nitride (NbN) ultra-thin films that were epitaxially grown on single-crystal MgO substrates, and optical cavity structure were applied for improvement of photo absorption efficiency. The SNSPD system was developed based on a compact Gifford-McMahon (GM) cryocooler, in which SNSPD can operate continuously at temperature of 2.9 K +/- 10 mK with low power consumption without any liquid cryogens. The system detection efficiencies at 1550 nm wavelength (at a 100 Hz dark count rate) were found to be 2.6% for device without optical cavity and 21% for device with optical cavity. The response speed of devices showed maximally 200 MHz with 5 × 5 mm square device, and timing jitter of 100 ps full width at a half maximum (FWHM) was observed.

IEEE International Conference on Space Optical Systems and Applications (ICSOS)•May 1, 2011•0 citations

Opto-electronic bias of a superconducting nanowire single photon detector using a cryogenic photodiode

Frederik Thiele, Thomas Hummel, Maximilian Protte +1 more

Superconducting Nanowire Single Photon Detectors (SNSPDs) have become an integral part of quantum optics in recent years because of their high performance in single photon detection. We present a method to replace the electrical input by supplying the required bias current via the photocurrent of a photodiode situated on the cold stage of the cryostat. Light is guided to the bias photodiode through an optical fiber, which enables a lower thermal conduction and galvanic isolation between room temperature and the cold stage. We show that an off-the-shelf InGaAs–InP photodiode exhibits a responsivity of at least 0.55 A/W at 0.8 K. Using this device to bias an SNSPD, we characterize the count rate dependent on the optical power incident on the photodiode. This configuration of the SNSPD and photodiode shows an expected plateau in the single photon count rate with an optical bias power on the photodiode above 6.8 µW. Furthermore, we compare the same detector under both optical and electrical bias, and show there is no significant changes in performance. This has the advantage of avoiding an electrical input cable, which reduces the latent heat load by a factor of 100 and, in principle, allows for low loss RF current supply at the cold stage.

APL Photonics•Aug 1, 2022•9 citations
We discuss the design and development of a cryogenic set-up down to ~1.8 K for carrying out measurements on superconducting nanowire single-photon detectors.The set-up consists of two separate low-temperature inserts, one for electrical characterization and the other for optical measurements and characterization of single-photon detectors.A sample holder with necessary arrangements for precise alignment of laser light with the active area of the device to enhance optical coupling efficiency has been designed for the optical probe.The invar alloy has been used for the sample holder to ensure that the alignment is not disturbed at low temperature.Single-mode fibres due to their high transmission rate, minimum attenuation and least distortion have been used to shine light on the samples.The sample holder with 20-pin LCC socket and matching chip carrier provides convenient and fast sample mounting in the electrical insert.Mumetal has been employed to cover the sample space in both the inserts in order to attenuate any electromagnetic interference.Temperature stability with the passage of time has been monitored.It has been found that variation in temperature is less than 10 mK at the lowest operating temperature.Another important advantage of the system is its low enough liquid helium loss rate (~100 ml/h) with all inserts, which allows uninterrupted measurements for several days without any refilling of liquid helium.
Superconducting nanowire single-photon detectors (SNSPDs) are nanodevices usually made from thin niobium nitride (NbN) films. Operated at liquid helium temperature, they can exhibit high detection efficiency with low dark-counts associated with a fast response time and a low timing jitter. Covering a broad detection range from ultraviolet to mid-infrared, SNSPDs are a very attractive alternative to silicon or gallium arsenide based semiconductor detectors for fiber based telecommunication when single-photon sensitivity and high counting rates are necessary. \nEfficient packaging and fiber coupling of a SNSPD is in itself a real challenge and is often a limiting factor in reaching high system quantum efficiency. Our approach makes use of a controlled expansion alloy which has been adequately heat treated to enhance its characteristics for cryogenic operation. This insures the integrity of the optical coupling at cryogenic temperatures while done at room temperature. It also provides a good attenuation for electromagnetic interference due to the high relative permeability of the nickel-iron alloy. The small form factor of this pigtailed optical fiber package makes it versatile and could be easily integrated with a commercial cryogen-free system or simply dipped into a standard helium transport Dewar. We report on our theoretical and experimental methodology to evaluate the optical coupling quality and present the optoelectronic characterization of two devices packaged in this way. Electrical simulation is studied to understand the speed limitation factor inherent to these devices and preliminary speed and jitter measurements are reported.
Superconducting nanowire single photon detectors (SNSPDs) are a rapidly maturing detector technology that offer superior performance relative to competing infrared photon counting technologies. The original experimental work presented here explores three novel methods of improving and analysing detector characteristics, employing low-temperature piezoelectric motors at temperatures below 4 K in a closed-cycle cryostat. Utilizing the low-temperature piezoelectric nanopositioners in tandem with a miniature confocal microscope, this work specifically shows a spatially-separable parallel-wire SNSPD demonstrating one- and two-pixel photon discrimination, with the detector responding more quickly when triggering two pixels. The work demonstrates nanoantenna-coupled SNSPDs, which are simulated, designed, and tested using the same nano-optical setup. In these an increased local absorption into the nanowire is seen at the antennas' resonant wavelengths, enhancing the efficiency of the detector by up to 130 %. Finally, a modified optical setup using a distributed Bragg reflector fibre in place of the microscope to form a tunable cavity around two configurations of SNSPD is demonstrated, improving absorption of the incident light into the nanowire across the whole active area. For these, enhancement in the system detection efficiency of up to 40 % is seen.
Superconductive nanowire single-photon detectors (SNSPDs) are an emerging, ultrasensitive photon counting technology which may enable fiber-based, long-haul quantum key distribution.Our group has successfully developed a robust process to fabricate SNSPDs, and has demonstrated device-detection-efficiency above 50% at near infrared wavelengths [1].However, one remaining challenge must be takenefficiently coupling light into the detector.This step is difficult because of the small active area of the SNSPD and its low temperature operation.In this thesis, I have designed two experimental setups to couple the light from fiber to the detector at a cryogenic temperature of 4 K: one is for immersion device-testing in a dewar; another is for packaging the detector inside a cryocooler.In addition, I have designed and fabricated SNSPDs suitable for the coupling with single-mode fiber, based on my theoretical calculation of the system detection-efficiency.Some important parameters to characterize the detectors such as system-detection-efficiency, dark-count rate, and counting rate vs. optical input power have been measured.
Efficient packaging and fiber coupling of a superconducting niobium nitride nanowire single photon detector is in itself a real challenge and is often a limiting factor to reach a high system quantum efficiency. Our approach makes use of a controlled expansion alloy, Carpenter Invar 36, that has been adequately heat treated to enhance its characteristics for cryogenic operation. This insures the integrity of the optical coupling done at room temperature while providing a good attenuation for electromagnetic interference due to the high relative permeability of this nickel-iron alloy. The small form factor of this optical fiber pigtailed package makes it versatile and could be easily integrated with a commercial cryogen-free system or simply dipped into a standard helium transport Dewar. We report on our experimental methodology to evaluate the optical coupling quality and present the optoelectronic characterization of two devices packaged in this way.
We have developed a practical superconducting nanowire single photon detector (SNSPD) system with our superconducting thin films and devices fabrication, optical coupling packaging, and cryogenic technology. The SNSPD devices were fabricated from high-quality niobium nitride (NbN) ultra-thin films that were epitaxially grown on single-crystal MgO substrates, and optical cavity structure were applied for improvement of photo absorption efficiency. The SNSPD system was developed based on a compact Gifford-McMahon (GM) cryocooler, in which SNSPD can operate continuously at temperature of 2.9 K +/- 10 mK with low power consumption without any liquid cryogens. The system detection efficiencies at 1550 nm wavelength (at a 100 Hz dark count rate) were found to be 2.6% for device without optical cavity and 21% for device with optical cavity. The response speed of devices showed maximally 200 MHz with 5 × 5 mm square device, and timing jitter of 100 ps full width at a half maximum (FWHM) was observed.
Superconducting Nanowire Single Photon Detectors (SNSPDs) have become an integral part of quantum optics in recent years because of their high performance in single photon detection. We present a method to replace the electrical input by supplying the required bias current via the photocurrent of a photodiode situated on the cold stage of the cryostat. Light is guided to the bias photodiode through an optical fiber, which enables a lower thermal conduction and galvanic isolation between room temperature and the cold stage. We show that an off-the-shelf InGaAs–InP photodiode exhibits a responsivity of at least 0.55 A/W at 0.8 K. Using this device to bias an SNSPD, we characterize the count rate dependent on the optical power incident on the photodiode. This configuration of the SNSPD and photodiode shows an expected plateau in the single photon count rate with an optical bias power on the photodiode above 6.8 µW. Furthermore, we compare the same detector under both optical and electrical bias, and show there is no significant changes in performance. This has the advantage of avoiding an electrical input cable, which reduces the latent heat load by a factor of 100 and, in principle, allows for low loss RF current supply at the cold stage.