Optomechanical systems can convert the microwave signal into the optical one, which provides us a candidate to detect weak microwave signal. Employing an optomechanical system, we investigate the effects of the non-Markovian environment on improving the sensitivity of weak microwave signal detection. Our results show that the non-Markovian environment with superohmic spectrum supports the improvement of sensitivity. A comparison between the direct measurement and homodyne detection shows that the latter can enhance the output power spectrum and reduce the additional noise because of the interference.
Optomechanical systems can convert the microwave signal into the optical one, which provides us a candidate to detect weak microwave signal. Employing an optomechanical system, we investigate the effects of the non-Markovian environment on improving the sensitivity of weak microwave signal detection. Our results show that the non-Markovian environment with superohmic spectrum supports the improvement of sensitivity. A comparison between the direct measurement and homodyne detection shows that the latter can enhance the output power spectrum and reduce the additional noise because of the interference.
Weak force amplification describes the process of amplifying a faint low-frequency signal by means of an additional high-frequency modulation, which plays a vital role in quantum sensing and high-precision measurement. However, the potential enhancement of weak-force amplification in non-Markovian environments has received little attention. In this paper, we firstly study the amplification of weak forces within cavity-optomechanical systems incorporating a degenerate optical parametric amplifier (DOPA) under the Markovian assumption. The results show that the weak force can be effectively amplified by using two high-frequency signals via vibrational resonance through adjusting the strength and phase of the DOPA with different pumping frequencies. Moreover, we extend the study of the amplification of the weak force to the non-Markovian environment which consists of a collection of infinite oscillators. We illustrate that the amplification exhibits a conversion from the non-Markovian regime to Markovian regime by controlling environmental spectral width. This conversion leads to enhancements of amplification, which originates from the excitation backflow obtained through the interaction between the cavity and non-Markovian environment. By controlling DOPA to amplify weak forces, the study achieves amplification in the non-Markovian regime, offering new directions for quantum optics research.
Entanglement between optical fields and microwave signals can be used as a quantum optical sensing technique to detect received microwave signals from a low-reflecting object which is encompassed by a bright thermal environment. Here, we introduce and analyze an optomechanical system for detecting weak reflected microwave signals from an object of low reflectivity. In our system, coupling and consequently entanglement between microwave and optical photons are achieved by means of a plasmonic wave. The main problem that can be moderated in the field of quantum optical sensing of weak microwave signals is suppressing the destructive effect of high temperatures on the entanglement between microwave signals and optical photons. For this purpose, we will show that our system can perform at high temperatures as well as low ones. It will be shown that the presence of the plasmonic wave can reduce the destructive effect of the thermal noises on the entanglement between microwave and optical photons. Also, we will show that the optomechanical interaction is vital to create an appropriate entanglement between microwave and optical photons.
Quantum squeezing-assisted noise suppression is a promising field with wide applications. However, the limit of noise suppression induced by squeezing is still unknown. This paper discusses this issue by studying weak signal detection in an optomechanical system. By solving the system dynamics in the frequency domain, we analyze the output spectrum of the optical signal. The results show that the intensity of the noise depends on many factors, including the degree or direction of squeezing and the choice of the detection scheme. To measure the effectiveness of squeezing and to obtain the optimal squeezing value for a given set of parameters, we define an optimization factor. With the help of this definition, we find the optimal noise suppression scheme, which can only be achieved when the detection direction exactly matches the squeezing direction. The latter is not easy to adjust as it is susceptible to changes in dynamic evolution and sensitive to parameters. In addition, we find that the additional noise reaches a minimum when the cavity (mechanical) dissipation κ(γ) satisfies the relation κ = Nγ, which can be understood as the restrictive relationship between the two dissipation channels induced by the uncertainty relation. Furthermore, by taking into account the noise source of our system, we can realize high-level noise suppression without reducing the input signal, which means that the signal-to-noise ratio can be further improved.
A theoretical scheme is proposed to enhance the signal-to-noise ratio in ultrasensitive detection by quantum correlation in a composite optomechanical system. Introducing an auxiliary oscillator and treating it as an added probe for weak-field detection, the additional noise can be greatly suppressed, which may even break the standard quantum limit. A magnetic field is employed as an example to exhibit the detection capability of the scheme. The result shows that, compared with the traditional detection protocol, the scheme has a higher signal-to-noise ratio and a better detection accuracy. Furthermore, the signal intensity detection curve shows a good linearity. The results provide a promising platform for reducing the additional noise by utilizing quantum correlation in ultrasensitive detection.
Cavity optomechanics provides a method for using laser photons to manipulate/detect mechanical objects inside optical cavities in the quantum regime [1]. It is attractive for applications in quantum information processing and ultra-sensitive detection. Inspired by the achievements of cavity optomechanics and circuit quantum electrodynamics (QED), researchers start to develop microwave optomechanical platforms by using microwave photons and superconducting resonators. These systems exhibit inherently many physical aspects from optics and exhibit desirable flexibilities in design and integration with nowadays’ quantum engineering architecture. Up to now, both input-output theory and Hamiltonian deduced from quantum optics are widely employed in microwave optomechanical systems. Here, we present the classical circuit model based on a lumped element LCR microwave circuit which has been widely used in microwave optomechanical experiment design [2]. Based on this model, we deduce analytical expressions to describe interactions between microwave signals and mechanical motions and also the thermal fluctuation spectrum of the mechanical oscillator as the output of the microwave cavity. In addition, we make a comparison between our classical LCR circuit model and the cavity optomechanical model derived from quantum optics and discuss critical parameters in the designing microwave optomechanical devices.[1] M. Aspelmeyer, T. J. Kippenberg, F. Marquardt, Rev. Mode. Phys. 86, 1391 (2014) [2] X. Zhou, D. Cattiaux, R. R. Gazizulin, A. Luck, O. Maillet, T. Crozes, J-F. Motte, O. Bourgeois, A. Fefferman, E. Collin, arXiv:1903.04992
Abstract The optomechanical system has developed a significant breakthrough in quantum science, especially since it can further improve the precision and sensitivity of the measurement in the quantum region. Here, we study a feasible optomechanical proposal in a hybrid quantum system, which can ensure a quantum sensor with further enhanced sensitivity. With the joint assistance of microwave modifying and optical parametric amplification, the effective line width of this supermode is further reduced around the critical point, and it can therefore result in a resolvable spectrum to display a much weaker mechanical frequency shift, which is perhaps induced by a tiny mass or charged particles in this system. We also hope there might be some useful applications for this attempt in the area of quantum measurement.