Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

SPIE Solid State Lasers: Technology and Devices

Gain dynamics in a highly ytterbium-doped potassium double tungstate thin-film amplifier

Yean-Sheng Yong, S. Aravazhi, Sergio Andrés Vázquez-Córdova, Jennifer L. Herek, Sonia M. García‐Blanco, Markus Pollnau

Published Mar 7, 2019• 0 citations
Publisher

Abstract

Active media with high rare-earth concentrations are essential for small-footprint waveguide amplifiers. When operating at high population inversion, such devices are often affected by undesired energy-transfer processes and thermal effects. In this work, we study a 32-μm-thick epitaxial layer of potassium gadolinium ytterbium double tungstate with a high Yb content of 57at.%, representing an Yb3+ concentration of ~3.8 × 1021 per cubic centimeter, grown onto an un-doped KY(WO4)2 substrate. The pump absorption, luminescence decay, and small-signal gain are investigated under intense pumping conditions. Spectroscopic signatures of an energy-transfer process and of quenched ions, as well as thermal effects are observed. We present a gain model which takes into account excessive heat generated due to the abovementioned experimental observations. Based on finite-element calculations, we find that the net gain is significantly reduced due to, firstly, a fraction of Yb3+ ions not contributing to stimulated emission, secondly, a reduction of population inversion owing to a parasitic energy-transfer process and, thirdly, degradation of the effective transition cross-sections owing to device heating. Nevertheless, a signal enhancement of 8.1 dB was measured from the sample at 981 nm wavelength when pumping at 932 nm. The corresponding signal net gain of ~800 dB/cm, which was achieved without thermal management, is promising for waveguide amplifier operating without active cooling.

DOI
10.1117/12.2514806

Related papers

Gain dynamics in a highly ytterbium-doped potassium double tungstate epitaxial layer

Yean-Sheng Yong, S. Aravazhi, Sergio Andrés Vázquez-Córdova +3 more

Active media with high rare-earth concentrations are essential for small-footprint waveguide amplifiers. When operating at high population inversion, such devices are often affected by undesired energy-transfer processes and thermal effects. In this work, we study a 32-μm-thick epitaxial layer of KGd0.43Yb0.57(WO4)2, representing an Yb3+ concentration of ∼3.8×1021 cm−3, grown on an undoped KY(WO4)2 substrate. The pump absorption, luminescence decay, and small-signal gain are investigated under intense pumping conditions. Spectroscopic signatures of an energy-transfer process and of quenched ions, as well as thermal effects, are observed. We present a gain model which takes into account excessive heat generated due to the abovementioned experimental observations. Based on finite-element calculations, we find that the net gain is significantly reduced due to, first, a fraction of Yb3+ ions not contributing to stimulated emission, second, a reduction of population inversion owing to a parasitic energy-transfer process and, third, degradation of the effective transition cross-sections owing to device heating. Nevertheless, a signal enhancement of 8.1 dB was measured from the sample at 981 nm wavelength when pumping at 932 nm. The corresponding signal net gain of ∼800 dB/cm, which was achieved without thermal management, is promising for a waveguide amplifier operating without active cooling.

Journal of the Optical Society of America B•Aug 17, 2018•7 citations

Direct confocal lifetime measurements on rare-earth-doped media exhibiting radiation trapping

Yean-Sheng Yong, S. Aravazhi, Sergio Andrés Vázquez-Córdova +5 more

Radiation trapping occurs in rare-earth-doped active media with strong spectral overlap of luminescence and ground-state absorption. It is demonstrated experimentally that a confocal measurement mitigates the influence of radiation trapping on the measured luminescence lifetime, hence allowing for direct extraction of the lifetime from the measured decay curves. The radiation trapping effect is largely suppressed by probing a small sample volume and rejecting the photons reemitted from the unpumped region. This non-destructive measurement method is applied to ytterbium (Yb3+) activated potassium double tungstate crystalline layers with Yb3+ concentrations ranging from 1.2 at.% up to 76 at.% (~8 × 1019 - 5 × 1021 cm-3). The measured lifetime values are comparable to the results reported for Yb3+-doped potassium double tungstate powder diluted in liquid.

Optical Materials Express•Jan 23, 2017•13 citations

A theoretical investigation of the optical gain in waveguide based on a silica matrix containing silicon nanograins and doped either withNd3+ or with Er3+ ions

Alexandre Fafin, Julien Cardin, Christian Dufour +1 more

We aim to amplify a signal in a strip loaded waveguide composed by an active silica layer co-doped with silicon nanograins and rare-earth ions deposited on a silica cladding layer and topped by a silica strip. The signal wavelength corresponds to the transition wavelength between two energy levels of a rare earth ions. To achieve an efficient population inversion, the rare earth ions benefit from the indirect excitation via silicon nanograins which show an absorption cross section fourfold higher than the one of rare earth ions. In order to study the influence of the type of rare earth on the optical gain, we consider two rare earth ions : neodymium ions (Nd3+) for a signal wavelength at 1060 nm and erbium ions (Er3+) for a signal wavelength at 1540 nm. The optical gain is simulated using a modified two loops auxiliary-differential equation and finite-difference time-domain (ADE-FDTD) algorithm. Within this new scheme we can compute the steady state levels populations as well as the spatial distribution of the guided field in the waveguide whatever the populations levels lifetime considered. We also calculate the gross gain as well as the net gain by taking into account the experimental background losses. We demonstrate that a significant positive net gain can only be achieved with the Nd3+ doped waveguide up to 30 dB/cm for a pump power density of 10^4 mW/mm².

•May 11, 2015•0 citations

Photonic Crystal Microcavity Amplifier

D. Biallo, Antonella D’Orazio, M. De Sario +3 more

Summary form only given: Amplification in rare-earth doped solid state planar optical structures has attracted a lot of interest in recent years due to the fact that the rare earth ions show sharp absorption and emission bands and relatively long luminescence lifetimes. In particular the erbium (Er) ion is very attractive because of its intra 4f-transition from the first excited state to the ground state around 1.53 mum (4I13/2-4I15/2). The main problem of the erbium doped waveguide amplifiers (EDWAs) is that high values of the Er3+concentration are required to reach high gain figures in a compact length, but in this way the concentration quenching effects become very considerable and detrimental to the optical gain, since they reduce the population in the first excited state. A good solution to overcome this dramatic drawback is to consider erbium doped photonic crystal amplifier (EDPCA). In fact the small group velocity of electromagnetic eigenmodes brings about the enhancement of stimulated emission if the photonic crystals are doped by active media as the rare earth ions E3+r or Yt3+. This phenomenon originates from the long interaction time between radiation field and the matter caused by the small group velocity near the edge of the photonic band gap. The efficient confinement of light is achievable not only by tuning the input signal at the band edge of the gap of the photonic crystal but it is also obtainable by introducing local defects inside photonic crystals. The density of electromagnetic states inside a cavity is significantly modified and the spontaneous emission of atoms in a cavity can be either enhanced or inhibited. Erbium doped silica-titania one-dimensional photonic crystal microcavities have been analyzed by solving the erbium rate equations and the Maxwell equations by means of an auxiliary differential equation finite difference time domain technique. Since the performance of optical amplifiers depends on the populations of the energy levels participating in radiative transitions, determined principally by the distribution and concentration of the rare-earth ions and by the pumping conditions, the relations between these parameters and the transmittance of the EDPCMA have been studied

International Conference on Transparent Optical Networks•Jun 1, 2006•0 citations

Luminescent instabilities and nonradiative processes in rare earth systems.

Shawn M. Redmond

This research is an outgrowth of earlier experiments that demonstrated bistable luminescence in heavy metal halide crystals doped with trivalent ytterbium ions. This type of instability has importance as a fundamentally new physical phenomenon with a potential application for fast all-optical switching as well as a limitation on compact solid state laser performance. In this thesis, the investigation of luminescent instabilities is extended to bistable energy transfer processes in crystals and to the observation of bistable blackbody emission in rare earth nanopowders. High resolution laser spectroscopy was used to study bistable luminescence and energy transfer in Yb,Er:CsCdBr3 crystals at cryogenic temperatures. For the first time, it was found that bistable behavior associated with Yb 3+ ions was transferred to Er 3+ through resonant energy transfer. Bistability of the resulting sensitized luminescence caused sufficiently dramatic changes in the crystal dynamics so as to change the color of emission from yellow to green. This color changing phenomenon is fully explained in the present work and is referred to as chromatic switching. Temperature is a critical variable that is known to govern luminescent instabilities in all current theories. Therefore, in a search for new systems with luminescent instabilities at high temperatures, materials with extreme thermal properties were investigated as part of this research. Yb,Er:Y 2O3 nanopowders were selected for this purpose. Nanopowders exhibit greatly reduced thermal conductivity and were verified during the course of this work to cause enhanced absorption as the result of multiple scattering. Significant spectral differences between Yb,Er:Y2O 3 nanopowders and single crystals also emerged. Measurements of erbium upconversion luminescence versus pump intensity in resonance with the ytterbium absorption transition revealed striking new optical phenomena: strong luminescent quenching, intense bistable blackbody emission, and the formation of single crystal micro-tubes directly from powder samples. A simple theoretical model was successfully developed to explain all these optical effects by a detailed balance approach to thermal transport that explicitly included erbium and ytterbium atomic level occupation probabilities, blackbody radiation and radiation trapping. Calculations of nanopowder sample luminescence accurately reproduced experimentally observed quenching, the onset of blackbody emission, bistability and details of hysteresis loops. The model also predicted that absorbed powers of less than 15 mW could melt yttria nanopowders (melting point = 2410°C), again in agreement with experiments. This work is expected to enable new approaches to laser processing of ceramics and laser machining of reflective metals, notably aluminum, using low power lasers.

•Jan 1, 2003•3 citations

An energy transfer accompanied by phonon absorption in ytterbium-doped yttrium aluminum perovskite for optical refrigeration

Yuta Nakayama, Yukihiro Harada, Takashi Kita

Yttrium aluminum perovskite (YAP) is a host material that can provide a strong emission from a rare-earth dopant and it has a lower phonon energy than yttrium aluminum garnet (YAG). Therefore, YAP is a promising material for optical refrigeration and radiation balanced laser. We measured the photoluminescence (PL) spectra of ytterbium (Yb)-doped YAP and compared them with those of Yb-doped YAG. The estimated ideal laser cooling efficiencies of Yb-doped YAP and Yb-doped YAG were comparable at 300 K. Based on the temperature-dependent anti-Stokes PL, we found that the laser cooling power of Yb-doped YAP at 470 K is 14.3 times higher than that at 200 K. This enhancement at higher temperatures is 3.2 times larger than that observed for Yb-doped YAG. We attributed the higher laser cooling power of Yb-doped YAP to a lower multi-phonon relaxation rate (and/or a higher energy transfer rate) and an antenna effect caused by the energy transfer from Yb ions that are located at the Y-site to Yb ions that are surrounded by an inhomogeneous alloy structure. The calculated small signal gain of (Yb:Y)AP is 3.5 times larger than that of (Yb:Y)AG. The larger small signal gain of (Yb:Y)AP arises from its strong absorbance and small Stark splitting width.

Applied Physics Letters•Jul 27, 2020•6 citations
Active media with high rare-earth concentrations are essential for small-footprint waveguide amplifiers. When operating at high population inversion, such devices are often affected by undesired energy-transfer processes and thermal effects. In this work, we study a 32-μm-thick epitaxial layer of potassium gadolinium ytterbium double tungstate with a high Yb content of 57at.%, representing an Yb3+ concentration of ~3.8 × 1021 per cubic centimeter, grown onto an un-doped KY(WO4)2 substrate. The pump absorption, luminescence decay, and small-signal gain are investigated under intense pumping conditions. Spectroscopic signatures of an energy-transfer process and of quenched ions, as well as thermal effects are observed. We present a gain model which takes into account excessive heat generated due to the abovementioned experimental observations. Based on finite-element calculations, we find that the net gain is significantly reduced due to, firstly, a fraction of Yb3+ ions not contributing to stimulated emission, secondly, a reduction of population inversion owing to a parasitic energy-transfer process and, thirdly, degradation of the effective transition cross-sections owing to device heating. Nevertheless, a signal enhancement of 8.1 dB was measured from the sample at 981 nm wavelength when pumping at 932 nm. The corresponding signal net gain of ~800 dB/cm, which was achieved without thermal management, is promising for waveguide amplifier operating without active cooling.
Active media with high rare-earth concentrations are essential for small-footprint waveguide amplifiers. When operating at high population inversion, such devices are often affected by undesired energy-transfer processes and thermal effects. In this work, we study a 32-μm-thick epitaxial layer of KGd0.43Yb0.57(WO4)2, representing an Yb3+ concentration of ∼3.8×1021 cm−3, grown on an undoped KY(WO4)2 substrate. The pump absorption, luminescence decay, and small-signal gain are investigated under intense pumping conditions. Spectroscopic signatures of an energy-transfer process and of quenched ions, as well as thermal effects, are observed. We present a gain model which takes into account excessive heat generated due to the abovementioned experimental observations. Based on finite-element calculations, we find that the net gain is significantly reduced due to, first, a fraction of Yb3+ ions not contributing to stimulated emission, second, a reduction of population inversion owing to a parasitic energy-transfer process and, third, degradation of the effective transition cross-sections owing to device heating. Nevertheless, a signal enhancement of 8.1 dB was measured from the sample at 981 nm wavelength when pumping at 932 nm. The corresponding signal net gain of ∼800 dB/cm, which was achieved without thermal management, is promising for a waveguide amplifier operating without active cooling.
Radiation trapping occurs in rare-earth-doped active media with strong spectral overlap of luminescence and ground-state absorption. It is demonstrated experimentally that a confocal measurement mitigates the influence of radiation trapping on the measured luminescence lifetime, hence allowing for direct extraction of the lifetime from the measured decay curves. The radiation trapping effect is largely suppressed by probing a small sample volume and rejecting the photons reemitted from the unpumped region. This non-destructive measurement method is applied to ytterbium (Yb3+) activated potassium double tungstate crystalline layers with Yb3+ concentrations ranging from 1.2 at.% up to 76 at.% (~8 × 1019 - 5 × 1021 cm-3). The measured lifetime values are comparable to the results reported for Yb3+-doped potassium double tungstate powder diluted in liquid.
We aim to amplify a signal in a strip loaded waveguide composed by an active silica layer co-doped with silicon nanograins and rare-earth ions deposited on a silica cladding layer and topped by a silica strip. The signal wavelength corresponds to the transition wavelength between two energy levels of a rare earth ions. To achieve an efficient population inversion, the rare earth ions benefit from the indirect excitation via silicon nanograins which show an absorption cross section fourfold higher than the one of rare earth ions. In order to study the influence of the type of rare earth on the optical gain, we consider two rare earth ions : neodymium ions (Nd3+) for a signal wavelength at 1060 nm and erbium ions (Er3+) for a signal wavelength at 1540 nm. The optical gain is simulated using a modified two loops auxiliary-differential equation and finite-difference time-domain (ADE-FDTD) algorithm. Within this new scheme we can compute the steady state levels populations as well as the spatial distribution of the guided field in the waveguide whatever the populations levels lifetime considered. We also calculate the gross gain as well as the net gain by taking into account the experimental background losses. We demonstrate that a significant positive net gain can only be achieved with the Nd3+ doped waveguide up to 30 dB/cm for a pump power density of 10^4 mW/mm².
Summary form only given: Amplification in rare-earth doped solid state planar optical structures has attracted a lot of interest in recent years due to the fact that the rare earth ions show sharp absorption and emission bands and relatively long luminescence lifetimes. In particular the erbium (Er) ion is very attractive because of its intra 4f-transition from the first excited state to the ground state around 1.53 mum (4I13/2-4I15/2). The main problem of the erbium doped waveguide amplifiers (EDWAs) is that high values of the Er3+concentration are required to reach high gain figures in a compact length, but in this way the concentration quenching effects become very considerable and detrimental to the optical gain, since they reduce the population in the first excited state. A good solution to overcome this dramatic drawback is to consider erbium doped photonic crystal amplifier (EDPCA). In fact the small group velocity of electromagnetic eigenmodes brings about the enhancement of stimulated emission if the photonic crystals are doped by active media as the rare earth ions E3+r or Yt3+. This phenomenon originates from the long interaction time between radiation field and the matter caused by the small group velocity near the edge of the photonic band gap. The efficient confinement of light is achievable not only by tuning the input signal at the band edge of the gap of the photonic crystal but it is also obtainable by introducing local defects inside photonic crystals. The density of electromagnetic states inside a cavity is significantly modified and the spontaneous emission of atoms in a cavity can be either enhanced or inhibited. Erbium doped silica-titania one-dimensional photonic crystal microcavities have been analyzed by solving the erbium rate equations and the Maxwell equations by means of an auxiliary differential equation finite difference time domain technique. Since the performance of optical amplifiers depends on the populations of the energy levels participating in radiative transitions, determined principally by the distribution and concentration of the rare-earth ions and by the pumping conditions, the relations between these parameters and the transmittance of the EDPCMA have been studied
This research is an outgrowth of earlier experiments that demonstrated bistable luminescence in heavy metal halide crystals doped with trivalent ytterbium ions. This type of instability has importance as a fundamentally new physical phenomenon with a potential application for fast all-optical switching as well as a limitation on compact solid state laser performance. In this thesis, the investigation of luminescent instabilities is extended to bistable energy transfer processes in crystals and to the observation of bistable blackbody emission in rare earth nanopowders. High resolution laser spectroscopy was used to study bistable luminescence and energy transfer in Yb,Er:CsCdBr3 crystals at cryogenic temperatures. For the first time, it was found that bistable behavior associated with Yb 3+ ions was transferred to Er 3+ through resonant energy transfer. Bistability of the resulting sensitized luminescence caused sufficiently dramatic changes in the crystal dynamics so as to change the color of emission from yellow to green. This color changing phenomenon is fully explained in the present work and is referred to as chromatic switching. Temperature is a critical variable that is known to govern luminescent instabilities in all current theories. Therefore, in a search for new systems with luminescent instabilities at high temperatures, materials with extreme thermal properties were investigated as part of this research. Yb,Er:Y 2O3 nanopowders were selected for this purpose. Nanopowders exhibit greatly reduced thermal conductivity and were verified during the course of this work to cause enhanced absorption as the result of multiple scattering. Significant spectral differences between Yb,Er:Y2O 3 nanopowders and single crystals also emerged. Measurements of erbium upconversion luminescence versus pump intensity in resonance with the ytterbium absorption transition revealed striking new optical phenomena: strong luminescent quenching, intense bistable blackbody emission, and the formation of single crystal micro-tubes directly from powder samples. A simple theoretical model was successfully developed to explain all these optical effects by a detailed balance approach to thermal transport that explicitly included erbium and ytterbium atomic level occupation probabilities, blackbody radiation and radiation trapping. Calculations of nanopowder sample luminescence accurately reproduced experimentally observed quenching, the onset of blackbody emission, bistability and details of hysteresis loops. The model also predicted that absorbed powers of less than 15 mW could melt yttria nanopowders (melting point = 2410°C), again in agreement with experiments. This work is expected to enable new approaches to laser processing of ceramics and laser machining of reflective metals, notably aluminum, using low power lasers.
Yttrium aluminum perovskite (YAP) is a host material that can provide a strong emission from a rare-earth dopant and it has a lower phonon energy than yttrium aluminum garnet (YAG). Therefore, YAP is a promising material for optical refrigeration and radiation balanced laser. We measured the photoluminescence (PL) spectra of ytterbium (Yb)-doped YAP and compared them with those of Yb-doped YAG. The estimated ideal laser cooling efficiencies of Yb-doped YAP and Yb-doped YAG were comparable at 300 K. Based on the temperature-dependent anti-Stokes PL, we found that the laser cooling power of Yb-doped YAP at 470 K is 14.3 times higher than that at 200 K. This enhancement at higher temperatures is 3.2 times larger than that observed for Yb-doped YAG. We attributed the higher laser cooling power of Yb-doped YAP to a lower multi-phonon relaxation rate (and/or a higher energy transfer rate) and an antenna effect caused by the energy transfer from Yb ions that are located at the Y-site to Yb ions that are surrounded by an inhomogeneous alloy structure. The calculated small signal gain of (Yb:Y)AP is 3.5 times larger than that of (Yb:Y)AG. The larger small signal gain of (Yb:Y)AP arises from its strong absorbance and small Stark splitting width.