Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Superconducting Sensors for Microwave and Optical Photon-Starved Communications (Plenary)

Bob Romanofsky

Published Jul 24, 2018• 1 citation
OpenAlex

Abstract

NASA mission modeling indicates a desire for approximately a tenfold data improvement per decade from the Deep Space Network through the year 2040. Some of this improvement will come from aperture enhancement and antenna arraying, increased use of Ka-band over X-band, and high performance optical terminals (e.g. 12 m ground telescope). The remainder will depend on "disruptive" technologies. Deep-space communications differs from near earth communications. One way light travel times are measured in minutes rather than seconds and distances involved are large enough such that optical signals are photon limited and microwave signals have extremely low flux density. High frequency SQIF receivers and single photon detectors for optical communications will be described. Specifically, progress towards a "noiseless" receiver based on arrays of incommensurate area SQUIDs, and single photon counting detectors based on superconducting nanowires and kinetic inductance effects, will be discussed. Finally, the design of an optimal array of optical telescopes to emulate performance of a monolithic 12 m telescope will be outlined. In this case, optimal means minimizing the initial capital investment and operational cost while maintaining performance requirements of the deep-space link.

Related papers

Superconducting nanowire arrays for multi-meter free-space optical communications receivers

William H. Farr, Jeffrey A. Stern, Matthew D. Shaw

Reception of faint optical communications signals from deep space presumes multi-meter diameter optical receivers coupled to high detection efficiency photon counting detectors. Superconducting nanowire detectors presently offer the highest performance for photon starved optical communications at near-infrared optical communications wavelengths. Square-millimeter sized arrays are required due to atmospheric turbulence and the classical solid angle-area invariant of an optical system, but most development of superconducting nanowire detectors has been for small pixels and arrays of less than 0.001 square-millimeter area. One deep space receiver approach is to partition detector area across multiple receive apertures (multiple telescopes) to use these small detectors, but this carries performance and cost penalties compared to use of a single large aperture. At JPL we are pursuing the development of large superconducting nanowire arrays for free space coupling to multi-meter telescopes and have developed a facility for testing large area free-space coupled nanowire arrays and fabricated arrays up to 64 pixels in the NbTiN and W(1-x)Six material systems.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Feb 9, 2012•0 citations

Performance and characterization of a modular superconducting nanowire single photon detector system for space-to-Earth optical communications links

Brian E. Vyhnalek, Sarah A. Tedder, Jennifer M. Nappier

Space-to-ground photon-counting optical communication links supporting high data rates over large distances require enhanced ground receiver sensitivity in order to reduce the mass and power burden on the spacecraft transmitter. Superconducting nanowire single-photon detectors (SNSPDs) have been demonstrated to offer superior performance in detection efficiency, timing resolution, and count rates over semiconductor photodetectors, and are a suitable technology for high photon efficiency links. Recently photon detectors based on superconducting nanowires have become commercially available, and we have assessed the characteristics and performance of one such commercial system as a candidate for potential utilization in ground receiver designs. The SNSPD system features independent channels which can be added modularly. We analyze the scalability of the system to support different data rates, as well as consider coupling concepts and issues as the number of channels increases.

Free-space laser communication technologies. Conference•Feb 15, 2018•10 citations

A review of next-generation superconducting kinetic inductance technologies for single-photon detection and spectroscopy in the far-infrared and submillimeter range

Omid Noroozian

Single-photon direct detectors in the submillimeter, far-IR and mid-IR range are highly desirable for reaching the sensitivity permitted by the low background noise of cryogenic-optics space telescopes, such as envisioned in NASA’s Origins Space Telescope concept. When combined with arrays of integrated spectrometers they can enable revolutionary advances in astrophysical studies such as fast spectroscopic surveys of the high redshift universe from space. Coherent receivers, which are fundamentally limited by quantum vacuum noise are critical for high-spectral-resolution studies of molecular and atomic emission lines and can reveal the origins of galaxies, stars, and even life. They can also enable future space-based VLBI missions, such as the Photon Ring Telescope concept, to study black holes. I will review recent advances in key superconducting technologies being developed for the above areas, including single-photon far/IR Kinetic Inductance Detectors, integrated submillimeter spectrometers, and quantum-limited kinetic inductance amplifiers for microwave readout of detectors and for mm/sub-mm coherent receivers.

Advanced Photon Counting Techniques•May 27, 2022•0 citations

Few-mode fiber coupled superconducting nanowire single-photon detectors for photon efficient optical communications

Brian E. Vyhnalek, Sarah A. Tedder, Evan J. Katz +1 more

The NASA Glenn Research Center's development of a high-photon efficiency real-time optical communications ground receiver has added superconducting nanowire single-photon detectors (SNSPDs) coupled with few-mode fibers (FMF). High data rate space-to-ground optical communication links require enhanced ground receiver sensitivity to reduce spacecraft transmitter constraints, and therefore require highly efficient coupling from fiber to detector. In the presence of atmospheric turbulence the received optical wavefront can be severely distorted introducing higher-order spatial mode components to the received signal. To reduce mode filtering and mismatch loss and the resulting degradations to detector coupling efficiency, we explore the use of few-mode fiber coupling to commercial single-pixel SNSPDs. Graded index 20-μm few-mode fibers allow the commercial single pixel SNSPD's active area to couple with equal efficiency as single mode fibers. Here we determine detector characteristics such as count rate, detection efficiency, dark counts, and jitter, as well as detection efficiencies for higher-order fiber spatial modes. Additionally, we assess the laboratory performance of the detectors in an optical system which emulates future deep space optical communications links.

Free-space laser communication technologies. Conference•Feb 22, 2019•13 citations

Superconducting nanowire single photon detectors for optical communication and astronomy

Matthew D. Shaw

Superconducting Nanowire Single Photon Detectors (SNSPDs) are the most advanced detectors available for time-resolved single photon counting from the UV to the mid-infrared. We will discuss recent progress in SNSPD development for the ground terminal in NASA’s Deep Space Optical Communication (DSOC) project as well as recent performance advances in other metrics, including the development of kilopixel SNSPD arrays, single-photon sensitivity at mid-infrared wavelengths as long as 10 microns, and SNSPDs with sub-3ps timing jitter. I will discuss a range of new potential scientific applications for SNSPDs, including exoplanet transit spectroscopy, dark matter detection, fluorescence lifetime imaging microscopy, and quantum information science.

X-Ray, Optical, and Infrared Detectors for Astronomy•Dec 14, 2020•1 citation

Superconducting Microwave Resonator Arrays for Submillimeter/Far-infrared Imaging

Omid Noroozian

Superconducting microwave resonators have the potential to revolutionize submillimeter and far-infrared astronomy, and with it our understanding of the universe. The field of low-temperature detector technology has reached a point where extremely sensitive devices like transition-edge sensors are now capable of detecting radiation limited by the background noise of the universe. However, the size of these detector arrays are limited to only a few thousand pixels. This is because of the cost and complexity of fabricating large-scale arrays of these detectors that can reach up to 10 lithographic levels on chip, and the complicated SQUID-based multiplexing circuitry and wiring for readout of each detector. In order to make substantial progress, next- generation ground-based telescopes such as CCAT or future space telescopes require focal planes with large-scale detector arrays of 104–106 pixels. Arrays using microwave kinetic inductance detectors (MKID) are a potential solution. These arrays can be easily made with a single layer of superconducting metal film deposited on a silicon substrate and pattered using conventional optical lithography. Furthermore, MKIDs are inherently multiplexable in the frequency domain, allowing ∼ 103 detectors to be read out using a single coaxial transmission line and cryogenic amplifier, drastically reducing cost and complexity. An MKID uses the change in the microwave surface impedance of a superconducting thin-film microresonator to detect photons. Absorption of photons in the superconductor breaks Cooper pairs into quasiparticles, changing the complex surface impedance, which results in a perturbation of resonator frequency and quality factor. For excitation and readout, the resonator is weakly coupled to a transmission line. The complex amplitude of a microwave probe signal tuned on-resonance and transmitted on the feedline past the resonator is perturbed as photons are absorbed in the superconductor. The perturbation can be detected using a cryogenic amplifier and subsequent homodyne mixing at room temperature. In an array of MKIDs, all the resonators are coupled to a shared feedline and are tuned to slightly different frequencies. They can be read out simultaneously using a comb of frequencies generated and measured using digital techniques. This thesis documents an effort to demonstrate the basic operation of ∼ 256 pixel arrays of lumped-element MKIDs made from superconducting TiNx on silicon. The resonators are designed and simulated for optimum operation. Various properties of the resonators and arrays are measured and compared to theoretical expectations. A particularly exciting observation is the extremely high quality factors (∼ 3 × 107) of our TiNx resonators which is essential for ultra-high sensitivity. The arrays are tightly packed both in space and in frequency which is desirable for larger full-size arrays. However, this can cause a serious problem in terms of microwave crosstalk between neighboring pixels. We show that by properly designing the resonator geometry, crosstalk can be eliminated; this is supported by our measurement results. We also tackle the problem of excess frequency noise in MKIDs. Intrinsic noise in the form of an excess resonance frequency jitter exists in planar superconducting resonators that are made on dielectric substrates. We conclusively show that this noise is due to fluctuations of the resonator capacitance. In turn, the capacitance fluctuations are thought to be driven by two-level system (TLS) fluctuators in a thin layer on the surface of the device. With a modified resonator design we demonstrate with measurements that this noise can be substantially reduced. An optimized version of this resonator was designed for the multiwavelength submillimeter kinetic inductance camera (MUSIC) instrument for the Caltech Submillimeter Observatory.

•Jun 12, 2012•14 citations
NASA mission modeling indicates a desire for approximately a tenfold data improvement per decade from the Deep Space Network through the year 2040. Some of this improvement will come from aperture enhancement and antenna arraying, increased use of Ka-band over X-band, and high performance optical terminals (e.g. 12 m ground telescope). The remainder will depend on "disruptive" technologies. Deep-space communications differs from near earth communications. One way light travel times are measured in minutes rather than seconds and distances involved are large enough such that optical signals are photon limited and microwave signals have extremely low flux density. High frequency SQIF receivers and single photon detectors for optical communications will be described. Specifically, progress towards a "noiseless" receiver based on arrays of incommensurate area SQUIDs, and single photon counting detectors based on superconducting nanowires and kinetic inductance effects, will be discussed. Finally, the design of an optimal array of optical telescopes to emulate performance of a monolithic 12 m telescope will be outlined. In this case, optimal means minimizing the initial capital investment and operational cost while maintaining performance requirements of the deep-space link.
Reception of faint optical communications signals from deep space presumes multi-meter diameter optical receivers coupled to high detection efficiency photon counting detectors. Superconducting nanowire detectors presently offer the highest performance for photon starved optical communications at near-infrared optical communications wavelengths. Square-millimeter sized arrays are required due to atmospheric turbulence and the classical solid angle-area invariant of an optical system, but most development of superconducting nanowire detectors has been for small pixels and arrays of less than 0.001 square-millimeter area. One deep space receiver approach is to partition detector area across multiple receive apertures (multiple telescopes) to use these small detectors, but this carries performance and cost penalties compared to use of a single large aperture. At JPL we are pursuing the development of large superconducting nanowire arrays for free space coupling to multi-meter telescopes and have developed a facility for testing large area free-space coupled nanowire arrays and fabricated arrays up to 64 pixels in the NbTiN and W(1-x)Six material systems.
Space-to-ground photon-counting optical communication links supporting high data rates over large distances require enhanced ground receiver sensitivity in order to reduce the mass and power burden on the spacecraft transmitter. Superconducting nanowire single-photon detectors (SNSPDs) have been demonstrated to offer superior performance in detection efficiency, timing resolution, and count rates over semiconductor photodetectors, and are a suitable technology for high photon efficiency links. Recently photon detectors based on superconducting nanowires have become commercially available, and we have assessed the characteristics and performance of one such commercial system as a candidate for potential utilization in ground receiver designs. The SNSPD system features independent channels which can be added modularly. We analyze the scalability of the system to support different data rates, as well as consider coupling concepts and issues as the number of channels increases.
Single-photon direct detectors in the submillimeter, far-IR and mid-IR range are highly desirable for reaching the sensitivity permitted by the low background noise of cryogenic-optics space telescopes, such as envisioned in NASA’s Origins Space Telescope concept. When combined with arrays of integrated spectrometers they can enable revolutionary advances in astrophysical studies such as fast spectroscopic surveys of the high redshift universe from space. Coherent receivers, which are fundamentally limited by quantum vacuum noise are critical for high-spectral-resolution studies of molecular and atomic emission lines and can reveal the origins of galaxies, stars, and even life. They can also enable future space-based VLBI missions, such as the Photon Ring Telescope concept, to study black holes. I will review recent advances in key superconducting technologies being developed for the above areas, including single-photon far/IR Kinetic Inductance Detectors, integrated submillimeter spectrometers, and quantum-limited kinetic inductance amplifiers for microwave readout of detectors and for mm/sub-mm coherent receivers.
The NASA Glenn Research Center's development of a high-photon efficiency real-time optical communications ground receiver has added superconducting nanowire single-photon detectors (SNSPDs) coupled with few-mode fibers (FMF). High data rate space-to-ground optical communication links require enhanced ground receiver sensitivity to reduce spacecraft transmitter constraints, and therefore require highly efficient coupling from fiber to detector. In the presence of atmospheric turbulence the received optical wavefront can be severely distorted introducing higher-order spatial mode components to the received signal. To reduce mode filtering and mismatch loss and the resulting degradations to detector coupling efficiency, we explore the use of few-mode fiber coupling to commercial single-pixel SNSPDs. Graded index 20-μm few-mode fibers allow the commercial single pixel SNSPD's active area to couple with equal efficiency as single mode fibers. Here we determine detector characteristics such as count rate, detection efficiency, dark counts, and jitter, as well as detection efficiencies for higher-order fiber spatial modes. Additionally, we assess the laboratory performance of the detectors in an optical system which emulates future deep space optical communications links.
Superconducting Nanowire Single Photon Detectors (SNSPDs) are the most advanced detectors available for time-resolved single photon counting from the UV to the mid-infrared. We will discuss recent progress in SNSPD development for the ground terminal in NASA’s Deep Space Optical Communication (DSOC) project as well as recent performance advances in other metrics, including the development of kilopixel SNSPD arrays, single-photon sensitivity at mid-infrared wavelengths as long as 10 microns, and SNSPDs with sub-3ps timing jitter. I will discuss a range of new potential scientific applications for SNSPDs, including exoplanet transit spectroscopy, dark matter detection, fluorescence lifetime imaging microscopy, and quantum information science.
Superconducting microwave resonators have the potential to revolutionize submillimeter and far-infrared astronomy, and with it our understanding of the universe. The field of low-temperature detector technology has reached a point where extremely sensitive devices like transition-edge sensors are now capable of detecting radiation limited by the background noise of the universe. However, the size of these detector arrays are limited to only a few thousand pixels. This is because of the cost and complexity of fabricating large-scale arrays of these detectors that can reach up to 10 lithographic levels on chip, and the complicated SQUID-based multiplexing circuitry and wiring for readout of each detector. In order to make substantial progress, next- generation ground-based telescopes such as CCAT or future space telescopes require focal planes with large-scale detector arrays of 104–106 pixels. Arrays using microwave kinetic inductance detectors (MKID) are a potential solution. These arrays can be easily made with a single layer of superconducting metal film deposited on a silicon substrate and pattered using conventional optical lithography. Furthermore, MKIDs are inherently multiplexable in the frequency domain, allowing ∼ 103 detectors to be read out using a single coaxial transmission line and cryogenic amplifier, drastically reducing cost and complexity. An MKID uses the change in the microwave surface impedance of a superconducting thin-film microresonator to detect photons. Absorption of photons in the superconductor breaks Cooper pairs into quasiparticles, changing the complex surface impedance, which results in a perturbation of resonator frequency and quality factor. For excitation and readout, the resonator is weakly coupled to a transmission line. The complex amplitude of a microwave probe signal tuned on-resonance and transmitted on the feedline past the resonator is perturbed as photons are absorbed in the superconductor. The perturbation can be detected using a cryogenic amplifier and subsequent homodyne mixing at room temperature. In an array of MKIDs, all the resonators are coupled to a shared feedline and are tuned to slightly different frequencies. They can be read out simultaneously using a comb of frequencies generated and measured using digital techniques. This thesis documents an effort to demonstrate the basic operation of ∼ 256 pixel arrays of lumped-element MKIDs made from superconducting TiNx on silicon. The resonators are designed and simulated for optimum operation. Various properties of the resonators and arrays are measured and compared to theoretical expectations. A particularly exciting observation is the extremely high quality factors (∼ 3 × 107) of our TiNx resonators which is essential for ultra-high sensitivity. The arrays are tightly packed both in space and in frequency which is desirable for larger full-size arrays. However, this can cause a serious problem in terms of microwave crosstalk between neighboring pixels. We show that by properly designing the resonator geometry, crosstalk can be eliminated; this is supported by our measurement results. We also tackle the problem of excess frequency noise in MKIDs. Intrinsic noise in the form of an excess resonance frequency jitter exists in planar superconducting resonators that are made on dielectric substrates. We conclusively show that this noise is due to fluctuations of the resonator capacitance. In turn, the capacitance fluctuations are thought to be driven by two-level system (TLS) fluctuators in a thin layer on the surface of the device. With a modified resonator design we demonstrate with measurements that this noise can be substantially reduced. An optimized version of this resonator was designed for the multiwavelength submillimeter kinetic inductance camera (MUSIC) instrument for the Caltech Submillimeter Observatory.