Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Conference on Precision Electromagnetic Measurements

Electrical Equivalent Loads of an End-Cap Ion-Trap

Subhadeep De, Lakhi Sharma, Neha Batra, Atish Roy, K. Sharma, Subhasis Panja, Vijay Narain Ojha

Published Jul 1, 2018• 0 citations
Publisher

Abstract

The resonant frequency of a helical resonator, that efficiently delivers high voltage rf to an electrodynamic ion-trap, depends on capacitive and inductive loads. Estimation of these loads for the parts that are attached to the resonator are thus necessary for designing a resonator operating at a desired frequency. On the other hand, the trapped ion experiences a voltage induced by the capacitance resulting from the electrodes. This results to excess micromotion to the ion. Here, we estimate the capacitive and resistive loads arising from different parts of ourtrap.

DOI
10.1109/cpem.2018.8500916

Related papers

Geometry-Resolved Projection of RF Imbalance to Ion Micromotion in a Same-Phase Dual-RF Blade Trap

Chun-Yang Luan, Haiyu Ding, Cheng-Kang Pan +8 more

Common-mode metrics of a high-$Q$ helical resonator do not determine the residual ion-side field in a dual-electrode drive. We combine a two-node differential RF model with single-electrode finite-element bases to obtain a computation-only, geometry-resolved projection for a same-phase blade trap. For a 3.5 pF external load per branch, the model gives a total effective branch capacitance of 7.640 pF and an HWHM-equivalent full branch-difference scale of 12.7 fF at $Q_{\mathrm{loaded}}=600$. The seven-segment geometry gives center and axial-RMS differential field coefficients of 640 V m$^{-1}$ and 635 V m$^{-1}$ per differential peak volt. A representative 10 fF mismatch with an effective 0.1 pF balance scale projects to 44.5/44.1 nm center/RMS $^{171}\mathrm{Yb}^{+}$ micromotion at 100 V common peak voltage. Supplementary thermal, bypass-admittance, and tested numerical cases characterize model sensitivity. All reported displacements are projections; no RF-bench or ion-side validation is claimed.

quant-pharXiv:2607.17793•Jul 21, 2026

Two-phase driving of a linear radio-frequency ion trap

Santhosh Surendra, Akos Hoffmann, Michael Köhl

A linear radio-frequency Paul trap is traditionally driven with one diagonal pair of electrodes grounded and the other connected to a high-voltage radio-frequency source. This method simplifies impedance matching of the voltage source to the trap. However, for several architectures it leads to increasing the axial micromotion amplitude, for example, when the capacitance between radio-frequency and end-cap electrodes is not negligible. Here, we present a technique to generate two high-voltage radio-frequency signals \SI{180}{\degree} out of phase to drive a linear Paul trap with opposite voltages between neighbouring electrodes. Using this, we have successfully trapped and cooled a chain of Ytterbium ions in a linear radio-frequency Paul trap.

quant-pharXiv:2602.07700•Review of Scientific Instruments•Feb 10, 2026•2 citations

A multi-channel voltage driving circuit with adjustable and independent RF amplitude

Qikun Wang, Zhao Wang, Tianyang Hu +3 more

Abstract A helical resonator with a certain resonant frequency and a high-quality factor (Q-factor)[1] is critical for an ion trap system, which results in a larger trap depth, longer trap time, and lower RF noise. Here we propose a new method for energizing amplitude-adjustable multiple RF ion trap electrodes. By dividing the output of the helical resonator into multiple circuits and simultaneously energizing the ion trap multi-RF electrodes, each circuit is composed of capacitors connected in series, and the desired amplitude is applied to the ion trap RF electrodes using capacitive voltage dividing. In contrast, the capacitance of the multi-RF capacitors connected in series is determined by three constraints. Different voltages for each circuit are realized while keeping the phase consistent. To demonstrate our proposed method in experiments, we first determine that the theory is feasible through circuit simulations and then confirm the method’s validity by comparing the measured results with the analog simulations. Our method can be applied to the ion trap structure of multiplexed RF electrodes, which contributes to the realization of ion traps for multiplexed RF electrodes.

Quantum Information Processing•May 12, 2025•0 citations

Cryogenic resonator design for trapped ion experiments in Paul traps

Matthias F. Brandl, Philipp Schindler, Thomas Monz +1 more

Trapping ions in Paul traps require high radio frequency voltages, which are generated using resonators. When operating traps in a cryogenic environment, an in-vacuum resonator showing low loss is crucial to limit the thermal load to the cryostat. In this study, we present a guide for the design and production of compact, shielded cryogenic resonators. We produced and characterized three different types of resonators and furthermore demonstrate efficient impedance matching of these resonators at cryogenic temperatures.

arXiv:1601.06699•Applied Physics B•May 18, 2016•13 citations

Design of an Ion Trap for Trapping Single 171 Yb

Subhadeep De, Neha Batra, Subhasis Panja +2 more

We present an ion trap design of end-cap geometry and numerically calculate its potential. An rf-resonator \nof quality factor 800(20) has been fabricated for delivering high voltage to the trap. An optical frequency standard will be developed by trapping and laser cooling a single 171Yb+. Optical arrangements for \nphotoionization, laser cooling and detection are also described.

•May 25, 2014•6 citations

New designed helical resonator to improve measurement accuracy of magic radio frequency

Tian Guo, Peiliang Liu, Chaohong Lee

Based upon the new designed helical resonator, the resonant radio frequency (RF) for trapping ions can be consecutively adjusted in a large range (about 12 MHz to 29 MHz) with high Q-factors (above 300). We analyze the helical resonator with a lumped element circuit model and find that the theoretical results fit well with the experimental data. With our resonator system, the resonant frequency near magic RF frequency (where the scalar Stark shift and the second-order Doppler shift due to excess micromotion cancel each other) can be continuously changed at kHz level. For 88Sr+ ion, compared to earlier results, the measurement accuracy of magic RF frequency can be improved by an order of magnitude upon rough calculation, and therefore the net micromotion frequency shifts can be further reduced. Also, the differential static scalar polarizability Δα 0 of clock transition can be experimentally measured more accurately.

Chinese Physics B•Apr 22, 2022•1 citation
The resonant frequency of a helical resonator, that efficiently delivers high voltage rf to an electrodynamic ion-trap, depends on capacitive and inductive loads. Estimation of these loads for the parts that are attached to the resonator are thus necessary for designing a resonator operating at a desired frequency. On the other hand, the trapped ion experiences a voltage induced by the capacitance resulting from the electrodes. This results to excess micromotion to the ion. Here, we estimate the capacitive and resistive loads arising from different parts of ourtrap.
Common-mode metrics of a high-QQQ helical resonator do not determine the residual ion-side field in a dual-electrode drive. We combine a two-node differential RF model with single-electrode finite-element bases to obtain a computation-only, geometry-resolved projection for a same-phase blade trap. For a 3.5 pF external load per branch, the model gives a total effective branch capacitance of 7.640 pF and an HWHM-equivalent full branch-difference scale of 12.7 fF at Qloaded=600Q_{\mathrm{loaded}}=600Qloaded​=600. The seven-segment geometry gives center and axial-RMS differential field coefficients of 640 V m−1^{-1}−1 and 635 V m−1^{-1}−1 per differential peak volt. A representative 10 fF mismatch with an effective 0.1 pF balance scale projects to 44.5/44.1 nm center/RMS 171Yb+^{171}\mathrm{Yb}^{+}171Yb+ micromotion at 100 V common peak voltage. Supplementary thermal, bypass-admittance, and tested numerical cases characterize model sensitivity. All reported displacements are projections; no RF-bench or ion-side validation is claimed.
A linear radio-frequency Paul trap is traditionally driven with one diagonal pair of electrodes grounded and the other connected to a high-voltage radio-frequency source. This method simplifies impedance matching of the voltage source to the trap. However, for several architectures it leads to increasing the axial micromotion amplitude, for example, when the capacitance between radio-frequency and end-cap electrodes is not negligible. Here, we present a technique to generate two high-voltage radio-frequency signals \SI{180}{\degree} out of phase to drive a linear Paul trap with opposite voltages between neighbouring electrodes. Using this, we have successfully trapped and cooled a chain of Ytterbium ions in a linear radio-frequency Paul trap.
Abstract A helical resonator with a certain resonant frequency and a high-quality factor (Q-factor)[1] is critical for an ion trap system, which results in a larger trap depth, longer trap time, and lower RF noise. Here we propose a new method for energizing amplitude-adjustable multiple RF ion trap electrodes. By dividing the output of the helical resonator into multiple circuits and simultaneously energizing the ion trap multi-RF electrodes, each circuit is composed of capacitors connected in series, and the desired amplitude is applied to the ion trap RF electrodes using capacitive voltage dividing. In contrast, the capacitance of the multi-RF capacitors connected in series is determined by three constraints. Different voltages for each circuit are realized while keeping the phase consistent. To demonstrate our proposed method in experiments, we first determine that the theory is feasible through circuit simulations and then confirm the method’s validity by comparing the measured results with the analog simulations. Our method can be applied to the ion trap structure of multiplexed RF electrodes, which contributes to the realization of ion traps for multiplexed RF electrodes.
Trapping ions in Paul traps require high radio frequency voltages, which are generated using resonators. When operating traps in a cryogenic environment, an in-vacuum resonator showing low loss is crucial to limit the thermal load to the cryostat. In this study, we present a guide for the design and production of compact, shielded cryogenic resonators. We produced and characterized three different types of resonators and furthermore demonstrate efficient impedance matching of these resonators at cryogenic temperatures.
Based upon the new designed helical resonator, the resonant radio frequency (RF) for trapping ions can be consecutively adjusted in a large range (about 12 MHz to 29 MHz) with high Q-factors (above 300). We analyze the helical resonator with a lumped element circuit model and find that the theoretical results fit well with the experimental data. With our resonator system, the resonant frequency near magic RF frequency (where the scalar Stark shift and the second-order Doppler shift due to excess micromotion cancel each other) can be continuously changed at kHz level. For 88Sr+ ion, compared to earlier results, the measurement accuracy of magic RF frequency can be improved by an order of magnitude upon rough calculation, and therefore the net micromotion frequency shifts can be further reduced. Also, the differential static scalar polarizability Δα 0 of clock transition can be experimentally measured more accurately.