Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

AIP Advances

Improving maximum count rate of superconducting nanowire single-photon detector with small active area using series attenuator

Chaolin Lv, Weijun Zhang, Lixing You, Peng Hu, Heqing Wang, Hao Li, Chengjun Zhang, Jia Huang, Yong Wang, Xiaoyan Yang, Zhen Wang, Xiaoming Xie

Published Oct 1, 2018• 14 citations
Publisher

Abstract

Maximum count rate is a crucial parameter of superconducting nanowire single-photon detector (SNSPD) for quantum communication and laser communication. However, when increasing the incident photon flux, the SNSPD device with small active area is apt to latch due to the AC coupling of room temperature amplifier in the readout circuit, which limits SNSPD to reach a high count rate. We proposed a simple way by inserting an electrical attenuator in series with small-active area SNSPD to avoid the latching effect, thus improving maximum count rate effectively. The count rate with the system detection efficiency reduced by half increased by 6 times for SNSPD with an active area of Φ15 μm.

DOI
10.1063/1.5049549

Related papers

Practical High-Efficiency SNSPD Balanced High Speed and Low Jitter on Filter Circuit

Changmin Li, Guangzhao Xu, Xingyu Zhang +7 more

Superconducting nanowire single-photon detectors (SNSPDs) are integral to the fields of quantum information and quantum communication, offering high efficiency, low dark count rate, high count rate, and minimal timing jitter. However, a common challenge with SNSPDs is their propensity for latching and nonlinear count rate increase under high incident photon fluxes due to the traditional external readout circuitry. This issue is primarily caused by large dynamic inductance and the ac-coupled effects of the bias and amplifier capacitors. In this study, we carefully selected a commercial SNSPD with an efficiency of over 95%. To address the aforementioned challenges, we implemented a resistor–inductor-type filter structure, which is directly coupled to a low-temperature amplifier, and their operating temperature is 40 K. Experimental results revealed that the enhanced SNSPD readout circuit achieves a count rate that is approximately 3.5 times greater than that of the traditional circuit. Moreover, the timing jitter of the SNSPD was optimized, decreasing by approximately 3.6 times under high incident photon fluxes. These performance enhancements could significantly improve high-speed optical communication and quantum precision measurement.

IEEE Transactions on Applied Superconductivity•Jul 15, 2024•4 citations

High comprehensive performance superconducting nanowire single photon detector

Ling-Ling Xi, Xiaoyan Yang, Tian-Zhu Zhang +3 more

Superconducting nanowire single photon detector (SNSPD) has been widely used in quantum communication, quantum computing and other fields because of its excellent timing jitter and response speed. However, due to the mutual restraint of the technical parameters of SNSPD nanowires, there are technical challenges to further improve the comprehensive performance of SNSPD, and thus limiting its application on a large scale. Combining high detection efficiency with high timing performance is still an outstanding challenge. In this work, we report the SNSPD with 12-μm small active area, which has high speed, high efficiency, low jitter and broadband absorption. Au/SiO2 membrane cavity, which is determined by finite element analysis simulation, is used to widen the optical response bandwidth. And it is easier to process and improve the alignment accuracy at the same time. The flat substrate is more conducive to the growth of superconducting thin films, so flattening process is introduced. Device package is also optimized to match smaller detector. Self-aligned packaging makes optical alignment more convenient and time-saving. Special optical fibers with small mode-field diameters can reduce the negative effect of the detector on optical coupling. The detector can achieve a maximum SDE of 82% at the central wavelength of 1310 nm and the temperature of 2.2 K, and the SDE of more than 65% in the wavelength range of 1200–1600 nm, with DCR of 70 cps. The detector also exhibits a count rate of 40 MHz@3 dB and a timing jitter of 38 ps, which is significantly improved compared with 23-μm active area detector. Furthermore, the minimum timing jitter of 22 ps can be obtained by using cryogenic amplifier readout. In this work, high comprehensive performance detector is developed, which provides an important technical reference for practical and product SNSPD.

Acta Physica Sinica•Jan 1, 2023•5 citations

Counting rate enhancements in superconducting nanowire single-photon detectors with improved readout circuits

Qingyuan Zhao, Tao Jia, Min Gu +6 more

Counting rates of superconducting nanowire single-photon detectors are usually estimated at hundreds of MHz by their kinetic-inductive reset time. This maximum is also limited by capacitor coupling effects in conventional readout circuits. In this Letter, we design and demonstrate an improved readout circuit that reduces the reset time and removes circuit limits. The counting rate at the 3 dB compression point is increased by four times for a large active area detector. We also discuss nonlinear dependences of the counting rate on the incident continuous-wave optical power and give a numerical model to explain our observations.

Optics Letters•Mar 20, 2014•47 citations

NbN superconducting nanowire single-photon detector with an active area of 300 μm-in-diameter

Chengjun Zhang, Weijun Zhang, Jia Huang +8 more

Superconducting nanowire single-photon detectors (SNSPDs) with both an ultra-large-active area and a high count rate (CR) are challenging from the design and fabrication. Here, we develop a NbN SNSPD with a circular active area of 300 μm-in-diameter and use multiple approaches to boost the maximal count rate (MCR). This large-active-area SNSPD is divided into nine pixels (parts). Each pixel consists of serially connected two superconducting nanowire avalanche photodetectors (SC-2SNAP), which yielded a four-fold reduction in the kinetic inductance of a single pixel. To further increase MCR, an optimized series resistance of about 380 Ω is added to each pixel, reducing the full recovery time of each pixel from a few microseconds to approximately 90 ns. All nine pixels show uniform superconducting critical temperatures of ∼7.4 K and switching currents in the range of 15.3–16.7 μA. When the detector coupled to a single-mode fiber and illuminated with 1064-nm photons, the single-pixel exhibits a well-saturated system detection efficiency (SDE) of 67% at a dark CR of 30 Hz, and its CR exceeds 10 MHz with an SDE of 50%. When coupled to a 200-μm multi-mode fiber, the total SDE of nine pixels is approximately 42% and the total MCR exceeds 43 MHz.

AIP Advances•Jul 1, 2019•28 citations

Characterization of parallel superconducting nanowire single photon detectors

Mikkel Ejrnaes, A. Casaburi, Orlando Quaranta +6 more

Superconducting nanowire single photon detectors (SNSPDs) have been realized using an innovative parallel wire configuration. This configuration allows, at the same time, a large detection area and a fast response, with the additional advantage of large signal amplitudes. The detectors have been thoroughly characterized in terms of signal properties (amplitude, risetime and falltime), detector operation (latching and not latching) and quantum efficiency (at 850 nm). It has been shown that the parallel SNSPD is able to provide significantly higher maximum count rates for large area SNSPDs than meandered SNSPDs. Through a proper parallel wire configuration the increase in maximum count rate can be obtained without latching problems.

Superconductor Science and Technology•Mar 30, 2009•57 citations

50 µm diameter superconducting nanowire single-photon detector with sub-17 ps timing jitter and high efficiency for visible wavelengths (Conference Presentation)

Jin Chang, Iman Esmaeil Zadeh

Superconducting nanowire single photon detectors (SNSPDs) have demonstrated advantages over traditional detectors in many fields [1]. Most fiber-coupled SNSPDs are coupled to single mode fibers, limiting their usability for applications where large surface area detectors are needed, for example fluorescence detection and satellite-based quantum communication [2][3]. Other important requirements for many applications are broadband detection efficiency, and low timing jitter [4]. So far, the increased meander length of multimode detectors, and the therefore increased kinetic inductance and number of imperfections due to film inhomogeneities have limited the timing jitter [5]. Moreover, combining low timing jitter with high detection efficiency and low dark count rate in one device is challenging due to the tradeoffs between different properties of SNSPDs [6]. In this paper, we achieved high efficiency and strong saturation over a broad wavelength range with a low timing jitter of 16.99 ps while maintaining a low dark count rate of < 0.2 Hz for an SNSPD coupled to a 50 µm core multimode fiber. To enhance the broadband absorption from 405 nm to 830 nm, detectors were fabricated on an optimized SiO2 cavity and Aluminum mirror. The geometry of the nanowire was also tuned to reach a good internal saturation of efficiency over the visible/NIR range but also to carry high current to get a large signal. Furthermore, a cryogenic readout amplifier was optimized to improve the signal to noise ratio and thus lead to high time resolution. Our devices can be readily used to enable higher resolution and faster quantum optics, bio-imaging, laser ranging and other optical experiments.

Quantum Optics and Photon Counting•May 13, 2019•0 citations
Maximum count rate is a crucial parameter of superconducting nanowire single-photon detector (SNSPD) for quantum communication and laser communication. However, when increasing the incident photon flux, the SNSPD device with small active area is apt to latch due to the AC coupling of room temperature amplifier in the readout circuit, which limits SNSPD to reach a high count rate. We proposed a simple way by inserting an electrical attenuator in series with small-active area SNSPD to avoid the latching effect, thus improving maximum count rate effectively. The count rate with the system detection efficiency reduced by half increased by 6 times for SNSPD with an active area of Φ15 μm.
Superconducting nanowire single-photon detectors (SNSPDs) are integral to the fields of quantum information and quantum communication, offering high efficiency, low dark count rate, high count rate, and minimal timing jitter. However, a common challenge with SNSPDs is their propensity for latching and nonlinear count rate increase under high incident photon fluxes due to the traditional external readout circuitry. This issue is primarily caused by large dynamic inductance and the ac-coupled effects of the bias and amplifier capacitors. In this study, we carefully selected a commercial SNSPD with an efficiency of over 95%. To address the aforementioned challenges, we implemented a resistor–inductor-type filter structure, which is directly coupled to a low-temperature amplifier, and their operating temperature is 40 K. Experimental results revealed that the enhanced SNSPD readout circuit achieves a count rate that is approximately 3.5 times greater than that of the traditional circuit. Moreover, the timing jitter of the SNSPD was optimized, decreasing by approximately 3.6 times under high incident photon fluxes. These performance enhancements could significantly improve high-speed optical communication and quantum precision measurement.
Superconducting nanowire single photon detector (SNSPD) has been widely used in quantum communication, quantum computing and other fields because of its excellent timing jitter and response speed. However, due to the mutual restraint of the technical parameters of SNSPD nanowires, there are technical challenges to further improve the comprehensive performance of SNSPD, and thus limiting its application on a large scale. Combining high detection efficiency with high timing performance is still an outstanding challenge. In this work, we report the SNSPD with 12-μm small active area, which has high speed, high efficiency, low jitter and broadband absorption. Au/SiO2 membrane cavity, which is determined by finite element analysis simulation, is used to widen the optical response bandwidth. And it is easier to process and improve the alignment accuracy at the same time. The flat substrate is more conducive to the growth of superconducting thin films, so flattening process is introduced. Device package is also optimized to match smaller detector. Self-aligned packaging makes optical alignment more convenient and time-saving. Special optical fibers with small mode-field diameters can reduce the negative effect of the detector on optical coupling. The detector can achieve a maximum SDE of 82% at the central wavelength of 1310 nm and the temperature of 2.2 K, and the SDE of more than 65% in the wavelength range of 1200–1600 nm, with DCR of 70 cps. The detector also exhibits a count rate of 40 MHz@3 dB and a timing jitter of 38 ps, which is significantly improved compared with 23-μm active area detector. Furthermore, the minimum timing jitter of 22 ps can be obtained by using cryogenic amplifier readout. In this work, high comprehensive performance detector is developed, which provides an important technical reference for practical and product SNSPD.
Counting rates of superconducting nanowire single-photon detectors are usually estimated at hundreds of MHz by their kinetic-inductive reset time. This maximum is also limited by capacitor coupling effects in conventional readout circuits. In this Letter, we design and demonstrate an improved readout circuit that reduces the reset time and removes circuit limits. The counting rate at the 3 dB compression point is increased by four times for a large active area detector. We also discuss nonlinear dependences of the counting rate on the incident continuous-wave optical power and give a numerical model to explain our observations.
Superconducting nanowire single-photon detectors (SNSPDs) with both an ultra-large-active area and a high count rate (CR) are challenging from the design and fabrication. Here, we develop a NbN SNSPD with a circular active area of 300 μm-in-diameter and use multiple approaches to boost the maximal count rate (MCR). This large-active-area SNSPD is divided into nine pixels (parts). Each pixel consists of serially connected two superconducting nanowire avalanche photodetectors (SC-2SNAP), which yielded a four-fold reduction in the kinetic inductance of a single pixel. To further increase MCR, an optimized series resistance of about 380 Ω is added to each pixel, reducing the full recovery time of each pixel from a few microseconds to approximately 90 ns. All nine pixels show uniform superconducting critical temperatures of ∼7.4 K and switching currents in the range of 15.3–16.7 μA. When the detector coupled to a single-mode fiber and illuminated with 1064-nm photons, the single-pixel exhibits a well-saturated system detection efficiency (SDE) of 67% at a dark CR of 30 Hz, and its CR exceeds 10 MHz with an SDE of 50%. When coupled to a 200-μm multi-mode fiber, the total SDE of nine pixels is approximately 42% and the total MCR exceeds 43 MHz.
Superconducting nanowire single photon detectors (SNSPDs) have been realized using an innovative parallel wire configuration. This configuration allows, at the same time, a large detection area and a fast response, with the additional advantage of large signal amplitudes. The detectors have been thoroughly characterized in terms of signal properties (amplitude, risetime and falltime), detector operation (latching and not latching) and quantum efficiency (at 850 nm). It has been shown that the parallel SNSPD is able to provide significantly higher maximum count rates for large area SNSPDs than meandered SNSPDs. Through a proper parallel wire configuration the increase in maximum count rate can be obtained without latching problems.
Superconducting nanowire single photon detectors (SNSPDs) have demonstrated advantages over traditional detectors in many fields [1]. Most fiber-coupled SNSPDs are coupled to single mode fibers, limiting their usability for applications where large surface area detectors are needed, for example fluorescence detection and satellite-based quantum communication [2][3]. Other important requirements for many applications are broadband detection efficiency, and low timing jitter [4]. So far, the increased meander length of multimode detectors, and the therefore increased kinetic inductance and number of imperfections due to film inhomogeneities have limited the timing jitter [5]. Moreover, combining low timing jitter with high detection efficiency and low dark count rate in one device is challenging due to the tradeoffs between different properties of SNSPDs [6]. In this paper, we achieved high efficiency and strong saturation over a broad wavelength range with a low timing jitter of 16.99 ps while maintaining a low dark count rate of < 0.2 Hz for an SNSPD coupled to a 50 µm core multimode fiber. To enhance the broadband absorption from 405 nm to 830 nm, detectors were fabricated on an optimized SiO2 cavity and Aluminum mirror. The geometry of the nanowire was also tuned to reach a good internal saturation of efficiency over the visible/NIR range but also to carry high current to get a large signal. Furthermore, a cryogenic readout amplifier was optimized to improve the signal to noise ratio and thus lead to high time resolution. Our devices can be readily used to enable higher resolution and faster quantum optics, bio-imaging, laser ranging and other optical experiments.