Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEICE Transactions on Electronics

Design of SFQ Circuits and Their Measurement

Kazunori Miyahara, Shuichi Nagasawa, H. Hasegawa, Tatsunori Hashimoto, Hideo Suzuki, Youichi Enomoto

Published Mar 1, 2002• 0 citations
OpenAlex

Related papers

Design and Measurement of zero static power SFQ circuit

Ryuta Tsutsumi

The Japan Society of Applied Physics•Feb 6, 2014•0 citations

Challenges in the Realization of SFQ Digital Circuits

T. Van Duzer

Springer eBooks•Jan 1, 1999•0 citations

Design Method of Single-Flux-Quantum Logic Circuits Using Dynamically Reconfigurable Logic Gates

Shohei Nishimoto, Yuki Yamanashi, Nobuyuki Yoshikawa

In this study, we designed and tested dynamically reconfigurable AND/OR and NAND/NOR single flux quantum (SFQ) logic gates. The measured dc bias margins at low frequency were 99%-126% and 121%-144% for AND/OR and NAND/NOR gates, respectively. The experimentally confirmed maximum operating frequencies of the AND/OR and NAND/NOR gates were 36 and 24 GHz, respectively. We investigated a circuit design method that enables the efficient design of SFQ logic circuits by using dynamically reconfigurable SFQ logic gates. The logic circuits were designed with a small number of gates using the input data pattern dependence of the Boolean function and reconfiguring the dynamically reconfigurable SFQ logic gates. As a case study, we designed and tested a bit-serial SFQ full adder using the investigated circuit design method. Compared with the conventional bit-serial SFQ full adder, the delay of the proposed full adder was reduced by 27%, assuming a clock frequency of 20 GHz. We confirmed correct operation of the adder with a low-speed test.

IEEE Transactions on Applied Superconductivity•Jan 1, 2015•10 citations

Design and Fabrication of All-NbN SFQ Circuits for SSPD Signal Processing

Kazumasa Makise, Hirotaka Terai, Shigehito Miki +2 more

We have developed an all-NbN integrated circuit technology for future integration of single flux quantum (SFQ) circuit with superconducting single-photon detector array. The all-NbN integrated circuits consist of epitaxial NbN/AlN/NbN tunnel junctions fabricated on single-crystal MgO substrates, Mo shunt resistors and 500-nm-thick NbN ground plane on the top. Critical current density and sheet resistance of the Mo resistor were set at 2.5 kA/cm2and 1.2 Ω, respectively. Current uniformity of the NbN/AlN/NbN tunnel junctions was measured to be σ = 3% for 3 μm × 3 μm junction size. The NbN-based SFQ logic cells were designed for and tested at 4.2 K. We actually measured circuit inductances of the fabricated SFQ cells. Circuit simulation revealed that the measured circuit inductances in the fabricated SFQ cells should allow operating margins of more than +/-20%.

IEEE Transactions on Applied Superconductivity•Dec 20, 2012•29 citations

Fundamental Research Toward SFQ-Integrated Circuits

Akira Fujimaki, Yasutoshi Suzuki, Hiroaki HASEGAWA +2 more

Springer eBooks•Jan 1, 2000•0 citations

SFQ Circuits With Ground Plane Hole-Assisted Inductive Coupling Designed With InductEx

Coenrad Johann Fourie, Olaf Wetzstein, J. Kunert +1 more

The design of single flux-quantum (SFQ) circuits requires well-defined inductances. In many cases these are created by irregular geometries and a computer-aided design tool is necessary for inductance calculations. This becomes a challenging task in cases where no ground plane is used and thus three-dimensional calculations are required. For this purpose, InductEx was developed and verified successfully for simple structures. In this work we take the next step and demonstrate the applicability of InductEx to the design of rapid single flux-quantum (RSFQ) cells. We use InductEx for inductance modeling as an integral part of the design cycle for an RSFQ cell with flux quantum transfer via mutual inductance and for a DC-reprogrammable logic circuit with similar inductive coupling. The relation between coupling factor and self-inductance is optimized in the circuit layout. All coupling structures are duplicated in SQUID modulation test circuits to measure and verify calculation accuracy. We find excellent agreement between the calculated and measured inductance values. Furthermore, the operational area of the basic cell is determined and compared with similar investigations reported earlier. Based on this comparison we conclude that InductEx is a valuable inductance design tool, and that mutual coupling in structures using ground plane holes and RSFQ-compatible self-inductances can be modeled and designed reliably.

IEEE Transactions on Applied Superconductivity•Nov 29, 2012•17 citations
In this study, we designed and tested dynamically reconfigurable AND/OR and NAND/NOR single flux quantum (SFQ) logic gates. The measured dc bias margins at low frequency were 99%-126% and 121%-144% for AND/OR and NAND/NOR gates, respectively. The experimentally confirmed maximum operating frequencies of the AND/OR and NAND/NOR gates were 36 and 24 GHz, respectively. We investigated a circuit design method that enables the efficient design of SFQ logic circuits by using dynamically reconfigurable SFQ logic gates. The logic circuits were designed with a small number of gates using the input data pattern dependence of the Boolean function and reconfiguring the dynamically reconfigurable SFQ logic gates. As a case study, we designed and tested a bit-serial SFQ full adder using the investigated circuit design method. Compared with the conventional bit-serial SFQ full adder, the delay of the proposed full adder was reduced by 27%, assuming a clock frequency of 20 GHz. We confirmed correct operation of the adder with a low-speed test.
We have developed an all-NbN integrated circuit technology for future integration of single flux quantum (SFQ) circuit with superconducting single-photon detector array. The all-NbN integrated circuits consist of epitaxial NbN/AlN/NbN tunnel junctions fabricated on single-crystal MgO substrates, Mo shunt resistors and 500-nm-thick NbN ground plane on the top. Critical current density and sheet resistance of the Mo resistor were set at 2.5 kA/cm2and 1.2 Ω, respectively. Current uniformity of the NbN/AlN/NbN tunnel junctions was measured to be σ = 3% for 3 μm × 3 μm junction size. The NbN-based SFQ logic cells were designed for and tested at 4.2 K. We actually measured circuit inductances of the fabricated SFQ cells. Circuit simulation revealed that the measured circuit inductances in the fabricated SFQ cells should allow operating margins of more than +/-20%.
The design of single flux-quantum (SFQ) circuits requires well-defined inductances. In many cases these are created by irregular geometries and a computer-aided design tool is necessary for inductance calculations. This becomes a challenging task in cases where no ground plane is used and thus three-dimensional calculations are required. For this purpose, InductEx was developed and verified successfully for simple structures. In this work we take the next step and demonstrate the applicability of InductEx to the design of rapid single flux-quantum (RSFQ) cells. We use InductEx for inductance modeling as an integral part of the design cycle for an RSFQ cell with flux quantum transfer via mutual inductance and for a DC-reprogrammable logic circuit with similar inductive coupling. The relation between coupling factor and self-inductance is optimized in the circuit layout. All coupling structures are duplicated in SQUID modulation test circuits to measure and verify calculation accuracy. We find excellent agreement between the calculated and measured inductance values. Furthermore, the operational area of the basic cell is determined and compared with similar investigations reported earlier. Based on this comparison we conclude that InductEx is a valuable inductance design tool, and that mutual coupling in structures using ground plane holes and RSFQ-compatible self-inductances can be modeled and designed reliably.