A primary challenge in quantum science and technology is to isolate the fragile quantum states from their environment in order to prevent the irreversible leakage of energy and information which causes decoherence. In the late 1990s, however, a new paradigm emerged, in which the environment itself, as well as the coupling to this environment of the quantum state, are engineered in ways which, counterintuitively, facilitate the creation and stabilization of desired quantum properties. This paradigm, coined reservoir engineering, has been pursued experimentally in various implementations, in which the states of trapped ions, atomic clouds or artificial atoms based on superconducting circuits were driven into a desired target state using a dissipative reservoir. In all these cases, the cold electromagnetic environment served as the engineered reservoir, capitalizing on the tremendous progress in the ability to shape the modes of the electromagnetic field using masers and lasers. In optomechanics, which is the study of the coupling between light and mechanical motion, a similar scenario has been prevalent. Light is used to read out and control the mechanical motion, and in the past few years, various optomechanical architectures both in the optical and microwave domain have enabled to push mechanical systems into the quantum regime. These results can be interpreted in the context of reservoir engineering: cooling and many other optomechanical phenomena exploit the cold, dissipative nature of light. This thesis reports on the development of a multimode superconducting circuit with a mechanically compliant element - fitting into the field of circuit cavity electromechanics -, with which we pursue two themes. In the first set of experiments, reversing the roles of dissipation described above, we engineer the mechanical oscillator into a cold, dissipative environment for microwave light. The mechanical element is the fundamental mode of a free-standing top electrode of a capacitor, 100 nm thick and 32 micron in diameter made of aluminum with an effective mass of around 170 pg, vibrating at a resonance frequency of 5.5 MHz. The dissipative mechanical reservoir is prepared using an auxiliary microwave mode with engineered parameters.We utilize it to control the properties - in particular, the susceptibility - of the electromagnetic field and to perform low-noise amplification close to the quantum limit. The noise analysis reveals that the reservoir is close to its quantum ground state with a mean thermal occupation number well below 1, demonstrating its utility as a resource in the quantum regime. We also show that the system can be driven to the parametric instability threshold, above which self-sustained oscillations of the microwave field (masing) is observed. Finally, we demonstrate injection locking of the maser using an external seed pump. In a second set of experiments, a similar electromechanical circuit is used to implement a microwave isolator based on optomechanical interactions. The overarching theme is that dissipation of the mechanical oscillator, albeit intrinsic and not engineered via an auxiliary mode s a key ingredient for the device to function as a nonreciprocal frequency converter and isolator. In these experiments, an additional mechanical mode is used, such that a 4-mode optomechanical plaquette is realized.
A primary challenge in quantum science and technology is to isolate the fragile quantum states from their environment in order to prevent the irreversible leakage of energy and information which causes decoherence. In the late 1990s, however, a new paradigm emerged, in which the environment itself, as well as the coupling to this environment of the quantum state, are engineered in ways which, counterintuitively, facilitate the creation and stabilization of desired quantum properties. This paradigm, coined reservoir engineering, has been pursued experimentally in various implementations, in which the states of trapped ions, atomic clouds or artificial atoms based on superconducting circuits were driven into a desired target state using a dissipative reservoir. In all these cases, the cold electromagnetic environment served as the engineered reservoir, capitalizing on the tremendous progress in the ability to shape the modes of the electromagnetic field using masers and lasers. In optomechanics, which is the study of the coupling between light and mechanical motion, a similar scenario has been prevalent. Light is used to read out and control the mechanical motion, and in the past few years, various optomechanical architectures both in the optical and microwave domain have enabled to push mechanical systems into the quantum regime. These results can be interpreted in the context of reservoir engineering: cooling and many other optomechanical phenomena exploit the cold, dissipative nature of light. This thesis reports on the development of a multimode superconducting circuit with a mechanically compliant element - fitting into the field of circuit cavity electromechanics -, with which we pursue two themes. In the first set of experiments, reversing the roles of dissipation described above, we engineer the mechanical oscillator into a cold, dissipative environment for microwave light. The mechanical element is the fundamental mode of a free-standing top electrode of a capacitor, 100 nm thick and 32 micron in diameter made of aluminum with an effective mass of around 170 pg, vibrating at a resonance frequency of 5.5 MHz. The dissipative mechanical reservoir is prepared using an auxiliary microwave mode with engineered parameters.We utilize it to control the properties - in particular, the susceptibility - of the electromagnetic field and to perform low-noise amplification close to the quantum limit. The noise analysis reveals that the reservoir is close to its quantum ground state with a mean thermal occupation number well below 1, demonstrating its utility as a resource in the quantum regime. We also show that the system can be driven to the parametric instability threshold, above which self-sustained oscillations of the microwave field (masing) is observed. Finally, we demonstrate injection locking of the maser using an external seed pump. In a second set of experiments, a similar electromechanical circuit is used to implement a microwave isolator based on optomechanical interactions. The overarching theme is that dissipation of the mechanical oscillator, albeit intrinsic and not engineered via an auxiliary mode s a key ingredient for the device to function as a nonreciprocal frequency converter and isolator. In these experiments, an additional mechanical mode is used, such that a 4-mode optomechanical plaquette is realized.
Harmonic oscillators might be one of the most fundamental entities described by physics. Yet they stay relevant in recent research. The topological properties associated with exceptional points that can occur when two modes interact have generated much interest in recent years. Harmonic oscillators are also at the heart of new quantum technological applications: the long lifetime of high-Q resonators make them advantageous as quantum memories, and they are employed for narrowband processing of quantum signals, as in Josephson parametric amplifiers. The goal of this thesis is to explore different fundamental regimes of two coupled harmonic oscillators using cavity optomechanics as the experimen- tal platform. With consistent progress in attaining ever increasing Q factors, mechanical and electromagnetic resonators realize near-ideal harmonic oscillators. By parametrically modulating the nonlinear optomechanical interaction between them, an effective linear coupling is achieved, which is tunable in strength and in the relative frequencies of the two modes. Thus cavity optomechanics provides a framework with excellent control over system parameters for the study of two coupled harmonic modes. The specific optomechanical implementation employed are superconducting circuits with the vibrating top plate of a capacitor as the mechanical element. Multimode optomechanical circuits are realized, with two microwave modes interacting with one or two mechanical oscillators. The supplementary modes serve either as intermediaries in the relation of the two modes of interest, or as auxiliaries used to control a parameter of the system. Three main experimental results are achieved. First, an auxiliary microwave mode allows the engineering of the effective dissipation rate of a mechanical oscillator. The latter then acts as a reservoir for the main microwave mode with which it interacts. The microwave mode susceptibility can be tuned, resulting in an instability akin to that of a maser and in resonant amplification of incoming microwave signals with an added noise close to the quantum minimum. Second, we study the conditions for a nonreciprocal interaction between two microwave modes, when the information flows in one direction but not in the other. The two modes interact through two mechanical oscillators, leading to frequency conversion between the two cavities. Dissipation in the mechanical modes is essential to the scheme in two ways: it provides a reciprocal phase necessary for the interference and eliminates the unwanted signals. Third, level attraction between a microwave and a mechanical mode is demonstrated, where the eigenfrequencies of the system are drawn closer as the result of interaction, rather distancing themselves as in the more usual case of level repulsion. The phenomenon is theoretically connected to exceptional points, and a general classification of the possible regimes of interaction between two harmonic modes is exposed, including level repulsion and attraction as special cases.
In the late 1960s and early 1970s, the development of mechanical resonators was pushed forward in efforts to record gravitational waves. In order to push down the limit of the smallest detectable force, the radiation circulating in a Fabry-Perot cavity was demonstrated to modify the damping of the cavity end-mirror suspended to act as a mechanical resonator. A few years later, motivated by the study of the internal properties of atoms and ions, the radiation pressure of light was realized as a means to cool atomic motion. In the following years, the ground-state cooling of ion motion was achieved in landmark studies. For mechanical resonators parametrically coupled to Fabry-Perot cavities, it took much longer to reach quantum ground-state cooling, both in the microwave domain, where the original experiments took place, and in the optical domain. Ground-state cooling in both regimes was reached by three groups during the preparation of this thesis and was largely due to advancements in the fabrication methods. \n \nGround-state cooling allows, in principle, the quantum nature of mechanical resonators to be probed and harnessed. Microwave domain devices, which are focused on in this thesis, have the advantage that nonlinear elements (superconducting quantum bits, qubits) are readily available. These elements enable nonclassical state preparation of the qubit and the subsequent transfer to the microwave cavity. The goal is to transfer these quantum states to mechanical resonators. This would allow mechanics to be used as a quantum mechanical memory in quantum information processing thanks to their long lifetimes. \n \nIn this thesis, various aspects of microwave domain circuit optomechanics are studied. The main goal of this thesis is to study how to enhance the coupling between a quantum regime microwave device and a mechanical resonator by using Josephson junction –based qubits. Coherent interaction between a superconducting qubit and a classical driven mechanical field is demonstrated. The analysis presented in this thesis predicts that ground-state cooling and coherent state transfer is possible in the single-phonon regime with transmon-regime qubits. Also, traditional linear optomechanical systems are considered in which the mechanical resonator is coupled to an electrical resonator. Such systems exhibit a rich spectrum of phenomena from which the quantum-limited amplification and multimode effects are considered in this thesis. It is shown that the system operates near quantum-limited amplification, which could be reached if the mechanical resonator was in the ground state.
Superconducting circuits are a powerful platform for studying and controlling the interaction between light and matter at the quantum level. In these systems, superconducting qubits act as artificial atoms (with matter-like degrees of freedom), whereas microwave resonators play the role of oscillators hosting photons (with photonic-like degrees of freedom). A major advantage of this platform is the ability to tailor the electromagnetic environment to which the qubits are coupled. This degree of control makes it possible to realize well-known quantum optics models, like the Jaynes-Cummings model, as well as more complex systems, like quantum electrodynamics close to a bandgap. In this thesis, we engineer structured electromagnetic environments and couple superconducting qubits to them to experimentally study their interaction. By coupling multiple microwave resonators together, we create a metamaterial. When an atom interacts with the metamaterial, an atom-photon bound state emerges. We observe the dynamics of the creation and dissolution of the atom-photon bound state, as well as the spectral content of its photonic component, for the first time to our knowledge.Our metamaterial is intrinsically nonlinear because each resonator is formed by an array of Josephson junctions to serve as an inductor. When the system is pumped, its phase diagram exhibits multimode dissipative phase transitions with timescales on the order of hundred seconds. There is ongoing theoretical debate about whether such phase transitions can occur in one-dimensional systems, a question we address and resolve in this work.Furthermore, we engineer qubit decay using two different approaches. In the first one, we engineer the decay of two coupled atoms to two waveguides by using a symmetric–antisymmetric coupling configuration. This approach enables selective coupling to bright and dark states of the system. In the second one, we suppress the Purcell decay of a qubit using a compact lumped-element Purcell filter. In addition, we characterize the Purcell decay by employing an auxiliary superconducting qubit as a sensitive power detector directly coupled to the feedline waveguide used for the qubit readout.In summary, this thesis presents three different methods for controlling light–matter interactions in structured quantum systems, including decay suppression with both Purcell filters and symmetry-selective couplings. The thesis also introduces new experimental techniques for probing atom-photon bound states and provides direct evidence of collective phenomena in driven-dissipative quantum metamaterials.
Engineered quantum systems are poised to revolutionize information science in the near future. A persistent challenge in applied quantum technology is creating controllable, quantum interactions while preventing information loss to the environment, decoherence. In this thesis, we realize mesoscopic superconducting circuits whose macroscopic collective degrees of freedom, such as voltages and currents, behave quantum mechanically. We couple these mesoscopic devices to microwave cavities forming a cavity quantum electrodynamics (QED) architecture comprised entirely of circuit elements. This application of cavity QED is dubbed Circuit QED and is an interdisciplinary field seated at the intersection of electrical engineering, superconductivity, quantum optics, and quantum information science. Two popular methods for taming active quantum systems in the presence of decoherence are discrete feedback conditioned on an ancillary system or quantum reservoir engineering. Quantum reservoir engineering maintains a desired subset of a Hilbert space through a combination of drives and designed entropy evacuation. Circuit QED provides a favorable platform for investigating quantum reservoir engineering proposals. A major advancement of this thesis is the development of a quantum reservoir engineering protocol which maintains the quantum state of a microwave cavity in the presence of decoherence. This thesis synthesizes strongly coupled, coherent devices whose solutions to its driven, dissipative Hamiltonian are predicted a priori. This work lays the foundation for future advancements in cavity centered quantum reservoir engineering protocols realizing hardware efficient circuit QED designs.
In the past several years, the field of optomechanics has progressed from proof-of-principle experiments to the realization of mechanical oscillators and measurements in the quantum regime. Mechanical oscillators are of great interest because they can have small dissipation rates, can couple to many different systems of interest, and are the fundamental elements of ultrasensitive force detectors. Coupling these mechanical oscillators to microwave or optical fields provides a twofold advantage. Firstly, information about mechanical position can be encoded in the interrogating field, enabling sensitive readout of the mechanical oscillator. Secondly, the radiation pressure force of that field can be used to control the state of the mechanical oscillator. Including a high-quality microwave or optical cavity enhances both of these effects, as the field strength is resonantly increased.\nThe major questions in the field of optomechanics in the last several years have dealt with using mechanical oscillators for ultrasensitive measurements and as tools for quantum information. Both of these goals have the prerequisite that we be able to read out the motion of the mechanical oscillator in a quantum efficient manner. To that end, we developed a nearly shot-noise limited microwave interferometer capable of measuring mechanical motion with an imprecision below that at the standard quantum limit. This achievement is not only a critical improvement for the electromechanical experiments we do, but is also an important tool for any experiment that encodes the information of interest in microwave fields. In order to use mechanical oscillators as tools for quantum information, the mechanical oscillator must also be cooled into the quantum regime and fully controllable by the interrogating fields. To this end, we used the radiation pressure of microwave fields to cool our macroscopic mechanical oscillator to less than one phonon. We also demonstrated coherent transfer between itinerant microwave states and the mechanical oscillator, even for incident fields with less than one photon of energy.\nThese accomplishments have set the foundation for further experiments to extend the quantum information abilities of optomechanical systems, couple diverse quantum systems via a mechanical intermediary, and potentially explore the foundations of quantum mechanics at macroscopic scales.
Due to its high coherence in transmission over a large distance in the ambient environment, the quantum optical system has been a prevailing platform for long-distance quantum communication, which was recently realized over a continental distance with a low earth orbit satellite and ground stations [102, 70]. However, the pure quantum optical system has so far shown weak interactions between photon and matter, which makes it inefficient in carrying out deterministic quantum gates for quantum repeater based scalable quantum network and quantum computing. On the other hand, superconducting quantum systems operating in the microwave domain with Josephson junction transmon qubits have proven to be capable of efficient deterministic quantum operations on quantum states [86, 87, 66]. Nevertheless, such architecture is prone to errors and decoherence due to cross-talk between microwave elements in a large-scale superconducting quantum circuit. Furthermore, superconducting systems, in general, also have large footprint (100s um) elements (resonators and superconducting quantum bits) [92, 60] that limit the ability to scale up a superconducting quantum system. Moreover, microwave quantum circuits require cooling to around 10 mK, making it unsuitable for communicating quantum information outside a dilution refrigerator (DF). Micro- and nano- acoustic elements have been extensively used in conventional integrated information processing systems due to their compactness and high coherence [97]. Acoustic systems in quantum engineering also have the advantage of being a platform for universal couplings between various quantum systems including spins, optical photons, and superconducting circuits. As it will be discussed in this thesis, elements critical to scalable optical quantum network and superconducting quantum circuit can be constructed relying on the cavity optomechanics and piezoelectric interactions. Optomechanical interaction is concerned with the light pressure coupling of cavity mechanical deformation to a strong optical field. This interaction has allowed the close to mechanical ground state cooling of mechanical resonators using laser and the ultra-sensitive displacement measurement that led to the detection of gravitational waves in the LIGO collaboration [125, 25]. Optomechanical crystals (OMCs) are lithographically patterned devices which contain a periodic structure that host bandgaps for both optical band electromagnetic waves and microwave band acoustic waves. A properly engineered defect in the crystal can confine and localize acoustic and electromagnetic modes of similar wavelengths into a small mode volume [17, 20, 21]. A strong optomechanical coupling, which can be achieved between such strongly confined co-localized optical and acoustic modes, can be used in engineering the quantum state of mechanical motion to realize useful quantum devices such as a high-coherence quantum memory [74] and an optomechanical high efficiency optical isolator for unidirectionally connecting distant optical cavities via an acoustic bus [37]. To strongly couple the mechanical degree of freedom with a superconducting quantum circuit, various methods can be used, ranging from electromechanic coupling (electric coupling to a mechanically compliant capacitor), magnetomechanical coupling (magnetic coupling to a vibrating SQUID loop), and piezoelectric coupling. The recent advent of quantum acoustics [23, 8, 9] was realized with the strong piezoelectric coupling between a superconducting transmon qubit and a high-coherence mechanical resonator. The engineered strong piezoacoustic coupling provides the possibility to carry out deterministic ultra-high fidelity two-qubit quantum gates on non-classical mechanical quantum states [52]. This ability together with the recent demonstration of ultra-long phonon lifetime mechanical resonators show the possibility of integrating the ultra-high quality mechanical resonator as a compact quantum memory element and even a new ultra-compact (10s um) quantum bit architecture for scalable superconducting quantum circuits. Furthermore, the strong piezoelectric coupling that can transduce quantum state in a superconducting circuit into mechanical wave also makes it possible to efficiently transduce a quantum state between a superconducting quantum circuit and a telecommunication band optical channel via a mechanical waveguide connected to an optomechanical crystal cavity.