Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Intrinsic Jitter in Photon Detection by Straight Superconducting Nanowires

Mariia Sidorova, Alexej D. Semenov, Artem A. Kuzmin, Ilya Charaev, Steffen Doerner, M. Siegel

Published May 18, 2018• 12 citations
Publisher

Abstract

Timing jitter inherent in photon detection by superconducting nanowire single-photon detectors has different values and behaves differently for detection events originating in bends and in straights of nanowires. Generally, jitter is larger for events in bends. Although, for typical meandering nanowire, contribution of bends to the integral jitter is almost negligible due to small geometric weight of bends in the meander, it reduces the accuracy of extracting the value of local jitter in straights. Here we report on the intrinsic jitter, which was measured in a straight nanowire without bends. Standard deviation in the intrinsic jitter for detection events in the straight nanowire is smaller than 6.5 ps for photons with the wavelength 794 nm and 7.7 ps for 1560 nm. This value is less than jitter magnitudes in straights, which were extracted from the jitter measured previously for the meandering nanowire. Coupling of photons to the nanowire through sufficiently long optical fiber increases integral jitter and causes asymmetry in the jitter histogram. However, this optical asymmetry differs qualitatively from the asymmetry caused by the detection process itself at small photon energies.

DOI
10.1109/tasc.2018.2836989

Related papers

Physical mechanisms of timing jitter in photon detection by current-carrying superconducting nanowires

Mariia Sidorova, Alexej D. Semenov, Heinz‐Wilhelm Hübers +4 more

We studied timing jitter in the appearance of photon counts in meandering nanowires with different fractional amount of bends. Intrinsic timing jitter, which is the probability density function of the random time delay between photon absorption in current-carrying superconducting nanowire and appearance of the normal domain, reveals two different underlying physical mechanisms. In the deterministic regime, which is realized at large photon energies and large currents, jitter is controlled by position-dependent detection threshold in straight parts of meanders. It decreases with the increase in the current. At small photon energies, jitter increases and its current dependence disappears. In this probabilistic regime jitter is controlled by Poisson process in that magnetic vortices jump randomly across the wire in areas adjacent to the bends.

arXiv:1707.05643•Physical review. B./Physical review. B•Nov 6, 2017•58 citations

Geometrical Jitter and Bolometric Regime in Photon Detection by Straight Superconducting Nanowire

Artem A. Kuzmin, Steffen Doerner, Mariia Sidorova +4 more

We present a direct observation of the geometrical jitter in single photon detection by a straight superconducting nanowire. Differential measurement technique was applied to the 180-μm long nanowire similar to those commonly used in the technology of superconducting nanowire single photon detectors (SNSPD). A non-Gaussian geometrical jitter appears as a wide almost uniform probability distribution (histogram) of the delay time (latency) of the nanowire response to detected photon. White electrical noise of the readout electronics causes broadened, Gaussian-shaped edges of the histogram. Subtracting noise contribution, we found for the geometrical jitter a standard deviation of ≈8.5 ps and the full width at half maximum (FWHM) of the distribution of ≈29 ps. FWHM corresponds to the propagation speed of the electrical signal along the nanowire of ≈6.2 × 106m/s or 0.02 of the speed of light. Alternatively the propagation speed was estimated from the central frequency of the measured first-order self-resonance of the nanowire. Both values agree well with each other and with previously reported values. As the intensity of the incident photon flux increases, the wide probability distribution collapses into a much narrower Gaussian distribution with a standard deviation dominated by the noise of electronics. We associate the collapse of the histogram with the transition from the discrete, single photon detection to the uniform bolometric regime.

arXiv:1812.06075•IEEE Transactions on Applied Superconductivity•Mar 28, 2019•6 citations

Timing jitter in photon detection by straight superconducting nanowires: Effect of magnetic field and photon flux

Mariia Sidorova, Alexej D. Semenov, Heinz‐Wilhelm Hübers +6 more

We studied the effects of the external magnetic field and photon flux on timing jitter in photon detection by straight superconducting NbN nanowires. At two wavelengths 800 and 1560 nm, statistical distribution in the appearance times of photon counts exhibits Gaussian shape at small times and an exponential tail at large times. The characteristic exponential time is larger for photons with smaller energy and increases with external magnetic field while variations in the Gaussian part of the distribution are less pronounced. Increasing photon flux drives the nanowire from the discrete quantum detection regime to the uniform bolometric regime that averages out fluctuations of the total number of nonequilibrium electrons created by the photon and drastically reduces jitter. The difference between standard deviations of Gaussian parts of distributions for these two regimes provides the measure for the strength of electron-number fluctuations; it increases with the photon energy. We show that the two-dimensional hot-spot detection model explains qualitatively the effect of magnetic field.

arXiv:1806.07183•Physical review. B./Physical review. B•Oct 11, 2018•24 citations

Superconducting nanowire detector jitter limited by detector geometry

Niccolò Calandri, Qingyuan Zhao, Di Zhu +2 more

Detection jitter quantifies variance introduced by the detector in the determination of photon arrival time. It is a crucial performance parameter for systems using superconducting nanowire single photon detectors (SNSPDs). In this work, we have demonstrated that the detection timing jitter is limited in part by the spatial variation of the photon detection events along the length of the wire. We define this jitter source as a geometric jitter since it is related to the length and area of the SNSPD. To characterize the geometric jitter, we have constructed a differential cryogenic readout with less than 7 ps of an electronic jitter that can amplify the pulses generated from the two ends of an SNSPD. By differencing the measured arrival times of the two electrical pulses, we were able to partially cancel out the difference of the propagation times and thus reduce the uncertainty of the photon arrival time. We proved that the variation of the differential propagation time was a few ps for a 3 μm × 3 μm device, while it increased up to 50 ps for a 20 μm × 20 μm device. In a 20 μm × 20 μm large SNSPD, we achieved a 20% reduction in the overall detection timing jitter for detecting the telecom-wavelength photons by using the differential cryogenic readout.

arXiv:1607.06713•Applied Physics Letters•Oct 10, 2016•114 citations

Intrinsically-limited timing jitter in molybdenum silicide superconducting nanowire single-photon detectors

Misael Caloz, Boris A. Korzh, Edward Ramirez +5 more

Recent progress in the development of superconducting nanowire single-photon detectors (SNSPDs) has delivered excellent performance and has had a great impact on a range of research fields. The timing jitter, which denotes the temporal resolution of the detection, is a crucial parameter for many applications. Despite extensive work since their apparition, the lowest jitter achievable with SNSPDs is still not clear, and the origin of the intrinsic limits is not fully understood. Understanding its intrinsic behavior and limits is a mandatory step toward improvements. Here, we report our experimental study on the intrinsically-limited timing jitter in molybdenum silicide SNSPDs. We show that to reach intrinsic jitter, crucial properties such as the latching current and the kinetic inductance of the devices have to be understood. The dependence on the nanowire thickness and the energy dependence of the intrinsic jitter are quantified, and the origin of the limits is exhibited. System timing jitter of 6.0 ps at 532 nm and 10.6 ps at 1550 nm photon wavelength has been obtained.

arXiv:1906.02073•Journal of Applied Physics•Oct 22, 2019•30 citations

50 µm diameter superconducting nanowire single-photon detector with sub-17 ps timing jitter and high efficiency for visible wavelengths (Conference Presentation)

Jin Chang, Iman Esmaeil Zadeh

Superconducting nanowire single photon detectors (SNSPDs) have demonstrated advantages over traditional detectors in many fields [1]. Most fiber-coupled SNSPDs are coupled to single mode fibers, limiting their usability for applications where large surface area detectors are needed, for example fluorescence detection and satellite-based quantum communication [2][3]. Other important requirements for many applications are broadband detection efficiency, and low timing jitter [4]. So far, the increased meander length of multimode detectors, and the therefore increased kinetic inductance and number of imperfections due to film inhomogeneities have limited the timing jitter [5]. Moreover, combining low timing jitter with high detection efficiency and low dark count rate in one device is challenging due to the tradeoffs between different properties of SNSPDs [6]. In this paper, we achieved high efficiency and strong saturation over a broad wavelength range with a low timing jitter of 16.99 ps while maintaining a low dark count rate of < 0.2 Hz for an SNSPD coupled to a 50 µm core multimode fiber. To enhance the broadband absorption from 405 nm to 830 nm, detectors were fabricated on an optimized SiO2 cavity and Aluminum mirror. The geometry of the nanowire was also tuned to reach a good internal saturation of efficiency over the visible/NIR range but also to carry high current to get a large signal. Furthermore, a cryogenic readout amplifier was optimized to improve the signal to noise ratio and thus lead to high time resolution. Our devices can be readily used to enable higher resolution and faster quantum optics, bio-imaging, laser ranging and other optical experiments.

Quantum Optics and Photon Counting•May 13, 2019•0 citations
Timing jitter inherent in photon detection by superconducting nanowire single-photon detectors has different values and behaves differently for detection events originating in bends and in straights of nanowires. Generally, jitter is larger for events in bends. Although, for typical meandering nanowire, contribution of bends to the integral jitter is almost negligible due to small geometric weight of bends in the meander, it reduces the accuracy of extracting the value of local jitter in straights. Here we report on the intrinsic jitter, which was measured in a straight nanowire without bends. Standard deviation in the intrinsic jitter for detection events in the straight nanowire is smaller than 6.5 ps for photons with the wavelength 794 nm and 7.7 ps for 1560 nm. This value is less than jitter magnitudes in straights, which were extracted from the jitter measured previously for the meandering nanowire. Coupling of photons to the nanowire through sufficiently long optical fiber increases integral jitter and causes asymmetry in the jitter histogram. However, this optical asymmetry differs qualitatively from the asymmetry caused by the detection process itself at small photon energies.
We studied timing jitter in the appearance of photon counts in meandering nanowires with different fractional amount of bends. Intrinsic timing jitter, which is the probability density function of the random time delay between photon absorption in current-carrying superconducting nanowire and appearance of the normal domain, reveals two different underlying physical mechanisms. In the deterministic regime, which is realized at large photon energies and large currents, jitter is controlled by position-dependent detection threshold in straight parts of meanders. It decreases with the increase in the current. At small photon energies, jitter increases and its current dependence disappears. In this probabilistic regime jitter is controlled by Poisson process in that magnetic vortices jump randomly across the wire in areas adjacent to the bends.
We present a direct observation of the geometrical jitter in single photon detection by a straight superconducting nanowire. Differential measurement technique was applied to the 180-μm long nanowire similar to those commonly used in the technology of superconducting nanowire single photon detectors (SNSPD). A non-Gaussian geometrical jitter appears as a wide almost uniform probability distribution (histogram) of the delay time (latency) of the nanowire response to detected photon. White electrical noise of the readout electronics causes broadened, Gaussian-shaped edges of the histogram. Subtracting noise contribution, we found for the geometrical jitter a standard deviation of ≈8.5 ps and the full width at half maximum (FWHM) of the distribution of ≈29 ps. FWHM corresponds to the propagation speed of the electrical signal along the nanowire of ≈6.2 × 106m/s or 0.02 of the speed of light. Alternatively the propagation speed was estimated from the central frequency of the measured first-order self-resonance of the nanowire. Both values agree well with each other and with previously reported values. As the intensity of the incident photon flux increases, the wide probability distribution collapses into a much narrower Gaussian distribution with a standard deviation dominated by the noise of electronics. We associate the collapse of the histogram with the transition from the discrete, single photon detection to the uniform bolometric regime.
We studied the effects of the external magnetic field and photon flux on timing jitter in photon detection by straight superconducting NbN nanowires. At two wavelengths 800 and 1560 nm, statistical distribution in the appearance times of photon counts exhibits Gaussian shape at small times and an exponential tail at large times. The characteristic exponential time is larger for photons with smaller energy and increases with external magnetic field while variations in the Gaussian part of the distribution are less pronounced. Increasing photon flux drives the nanowire from the discrete quantum detection regime to the uniform bolometric regime that averages out fluctuations of the total number of nonequilibrium electrons created by the photon and drastically reduces jitter. The difference between standard deviations of Gaussian parts of distributions for these two regimes provides the measure for the strength of electron-number fluctuations; it increases with the photon energy. We show that the two-dimensional hot-spot detection model explains qualitatively the effect of magnetic field.
Detection jitter quantifies variance introduced by the detector in the determination of photon arrival time. It is a crucial performance parameter for systems using superconducting nanowire single photon detectors (SNSPDs). In this work, we have demonstrated that the detection timing jitter is limited in part by the spatial variation of the photon detection events along the length of the wire. We define this jitter source as a geometric jitter since it is related to the length and area of the SNSPD. To characterize the geometric jitter, we have constructed a differential cryogenic readout with less than 7 ps of an electronic jitter that can amplify the pulses generated from the two ends of an SNSPD. By differencing the measured arrival times of the two electrical pulses, we were able to partially cancel out the difference of the propagation times and thus reduce the uncertainty of the photon arrival time. We proved that the variation of the differential propagation time was a few ps for a 3 μm × 3 μm device, while it increased up to 50 ps for a 20 μm × 20 μm device. In a 20 μm × 20 μm large SNSPD, we achieved a 20% reduction in the overall detection timing jitter for detecting the telecom-wavelength photons by using the differential cryogenic readout.
Recent progress in the development of superconducting nanowire single-photon detectors (SNSPDs) has delivered excellent performance and has had a great impact on a range of research fields. The timing jitter, which denotes the temporal resolution of the detection, is a crucial parameter for many applications. Despite extensive work since their apparition, the lowest jitter achievable with SNSPDs is still not clear, and the origin of the intrinsic limits is not fully understood. Understanding its intrinsic behavior and limits is a mandatory step toward improvements. Here, we report our experimental study on the intrinsically-limited timing jitter in molybdenum silicide SNSPDs. We show that to reach intrinsic jitter, crucial properties such as the latching current and the kinetic inductance of the devices have to be understood. The dependence on the nanowire thickness and the energy dependence of the intrinsic jitter are quantified, and the origin of the limits is exhibited. System timing jitter of 6.0 ps at 532 nm and 10.6 ps at 1550 nm photon wavelength has been obtained.
Superconducting nanowire single photon detectors (SNSPDs) have demonstrated advantages over traditional detectors in many fields [1]. Most fiber-coupled SNSPDs are coupled to single mode fibers, limiting their usability for applications where large surface area detectors are needed, for example fluorescence detection and satellite-based quantum communication [2][3]. Other important requirements for many applications are broadband detection efficiency, and low timing jitter [4]. So far, the increased meander length of multimode detectors, and the therefore increased kinetic inductance and number of imperfections due to film inhomogeneities have limited the timing jitter [5]. Moreover, combining low timing jitter with high detection efficiency and low dark count rate in one device is challenging due to the tradeoffs between different properties of SNSPDs [6]. In this paper, we achieved high efficiency and strong saturation over a broad wavelength range with a low timing jitter of 16.99 ps while maintaining a low dark count rate of < 0.2 Hz for an SNSPD coupled to a 50 µm core multimode fiber. To enhance the broadband absorption from 405 nm to 830 nm, detectors were fabricated on an optimized SiO2 cavity and Aluminum mirror. The geometry of the nanowire was also tuned to reach a good internal saturation of efficiency over the visible/NIR range but also to carry high current to get a large signal. Furthermore, a cryogenic readout amplifier was optimized to improve the signal to noise ratio and thus lead to high time resolution. Our devices can be readily used to enable higher resolution and faster quantum optics, bio-imaging, laser ranging and other optical experiments.