The superconductor-ferromagnetic transistor (SFT) is a novel cryogenic device with the potential to greatly enhance traditional single flux quantum (SFQ) circuits. Since SFT devices are under active development, compact models are necessary to evaluate this device in novel circuits. In this paper, a simplified compact model of a three terminal SFT device is proposed. The model fits the general I-V characteristics of existing devices with 7.4% mean absolute error, while also capturing the transient behavior of the device. The model has been implemented in Verilog-A and simulated in Cadence Spectre. The proposed model enables the simulation of SFQ circuits containing SFT devices, and is reconfigurable to support developments in SFT technology.
The superconductor-ferromagnetic transistor (SFT) is a novel cryogenic device with the potential to greatly enhance traditional single flux quantum (SFQ) circuits. Since SFT devices are under active development, compact models are necessary to evaluate this device in novel circuits. In this paper, a simplified compact model of a three terminal SFT device is proposed. The model fits the general I-V characteristics of existing devices with 7.4% mean absolute error, while also capturing the transient behavior of the device. The model has been implemented in Verilog-A and simulated in Cadence Spectre. The proposed model enables the simulation of SFQ circuits containing SFT devices, and is reconfigurable to support developments in SFT technology.
We report on the measurement results of the superconducting-ferromagnetic transistors (SFTs) made at Northwestern University and Hypres, Inc. [IEEE Trans. Appl. Supercond. vol. 24, 1800506 (2014); vol. 25, 1800705 (2015)]. SFT is a multi-terminal device with the SIS'FIFS structure (where S, I, and F denote a superconductor, an insulator, and a ferromagnetic material, respectively) exploiting intense quasiparticle injection in order to modify the non-linear I-V curve of a superconducting tunnel junction. Potentially, SFT is capable of providing voltage, current and power amplification while having good input/output isolation. We characterized the devices at frequencies up to 5 MHz at 4 K. Our setup did not allow for accurate measurement of the voltage gain of low-impedance SFT devices because of contribution of resistance of the bias-T connected in series with the SFT. Nevertheless we observed a voltage gain above unity for some measurement configurations. It is very interesting that we confirmed that the isolation between the input and output of the device is quite good. We suggest that further improvement of the SFT device parameters is possible in optimized devices, so that the device potentially may serve as a preamplifier for readout of output signals of cryogenic detectors and be useful as an element of other superconductor-based circuits.
We report on the measurement results of the superconducting-ferromagnetic transistors (SFTs). The devices were made at Northwestern University and Hypres (SeeQC), Inc. (Nevirkovets et al., 2014; 2015). SFT is a multiterminal device with the SIS'FIFS (or SFIFS'IS) structure (where S, I, and F denote a superconductor, an insulator, and a ferromagnetic material, respectively) exploiting intense quasiparticle injection in order to modify the nonlinear I-V curve of a superconducting tunnel junction. SFT is capable of providing voltage, current, and power amplification while having good input/output isolation. We characterized the devices using different measurement techniques. We measured S parameters of the single- and double-acceptor devices at frequencies up to 5 MHz. Importantly, we confirmed that the isolation between the input and output of the device is quite good. However, the techniques typically employed to characterize semiconductor devices do not allow for revealing the full potential of our low-resistive SFT devices, especially those having two acceptors. In the latter case, we also tested the devices using the battery-powered current sources with floating grounds. Analyzing double-acceptor I-V curves recorded at different levels of injection currents, for an optimal load, we deduced a small-signal voltage gain of 33 and a power gain of 2.4. We suggest that further improvement of the SFT device parameters is possible in optimized devices, so that the device potentially may serve as a preamplifier for readout of output signals of cryogenic detectors and be useful as an element of other superconductor-based circuits. In addition, we used scanning transmission electron microscopy to identify some problems in the fabrication of the devices without any planarization.
We report experimental results on characteristics of SFIFS junctions and multi-terminal SFIFSIS devices (where S, I, and F denote a superconductor (Nb), an insulator (AlOx), and a ferromagnetic material (Ni), respectively). The SFIFS junctions serve as injectors in the SFIFSIS devices which have transistor-like properties; for this reason we call them Superconducting-Ferromagnetic Transistors (SFTs). We have found the F (Ni) thickness at which the SFIFS current-voltage characteristic (CVC) becomes linear. Furthermore, we investigated the DC and AC characteristics of SFTs of two types: ordinary devices with a single acceptor (SIS) junction, and devices with a double acceptor. In the first case, we focused on studying the influence of the injection current through the SFIFS junction on the maximum Josephson current of the SIS acceptor. For devices of the second type, we studied voltage amplification properties when the operating point was chosen in the sub-gap region of the acceptor CVC. By applying an AC signal (in the kHz range) while biasing the injector (SFIFS) junction with a constant DC current, we observed a voltage gain above 25 on the double acceptor. In the reverse transmission experiment, we applied DC current and an AC modulation to the acceptor junction and, within the accuracy of the experiment, observed no response on the injector junction, which implies an excellent input-output isolation in our SFIFSIS devices. The experiments indicate that, after optimization of the device parameters, they can be used as input/output isolators and amplifiers for memory, digital, and RF applications.
The semiconductor industry standard computer-aided-design (CAD) tool Cadence has been calibrated for a 3 /spl mu/m Niobium technology in order to design and build superconductive single flux quantum (SFQ) circuits. The top-down design methodology includes Verilog functional simulation, schematic capture, graphic layout, functional verification, design rule checking, electrical rule checking, and layout-vs.-schematic verification. This design framework has been used successfully at the University of Rochester in designing more than 15 elementary SFQ cells and three large scale digital and mixed-signal SFQ circuits, demonstrating significant improvement in both design efficiency and accuracy.
The superconducting transistor, or Josephson Field Effect Transistor (JoFET), is a versatile building block for ultra-low-power and high-energy-efficiency classical and quantum electronics. In a JoFET, the superconducting current is controlled by electrostatic gate voltage, which enables the scalability of solid-state quantum computers and the creation of next-generation superconducting integrated circuits (ICs) for energy-efficient computing. The development of JoFETs has so far been limited to single devices or a few-transistor circuits due to the lack of a reproducible technological platform. Here, we first report on technological progress of wafer-scale JoFET manufacturing, demonstrating a 98% JoFET device yield on our 150 mm pilot-line platform. Then, we present behavioral and physics-based transistor models - an important step toward designing of novel JoFET-based superconducting ICs. Our models have been implemented in both commercial and freeware circuit simulators. A Verilog-A model implementation is provided with this paper. Using the proposed models, we obtain a good description of JoFET experimental data, thus paving the way for the large-scale design of next-generation superconducting ICs.
We report experimental results on the dc and ac characterization of multiterminal SFIFSIS devices (where S, I, and F denote a superconductor (Nb), an insulator (AlOx), and a ferromagnetic material (Ni), respectively), which display transistor-like properties. We investigated two types of such superconducting-ferromagnetic transistors (SFTs): ordinary devices with a single acceptor (SIS) junction, and devices with a double acceptor. The devices with the single SIS acceptor were investigated and demonstrated a modulation of the maximum Josephson current as a function of the SFIFS current injection level. For devices of the second type, by applying an ac signal (in the kilohertz range) with a constant dc bias current to the injector (SFIFS) junction, we observed a voltage gain of about 25 on the double acceptor with the operating point chosen in the subgap region of the acceptor current-voltage characteristic. We also observed an excellent input-output isolation in our SFIFSIS devices. The experiments indicate that, after optimization of the device parameters, they can be used as input/output isolators and amplifiers for memory, digital, and RF applications.