Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

SPIE Solid State Lasers: Technology and Devices

CW 3µm lasing via two-photon pumping in cesium vapor with a 1W source

Glen P. Perram, Christopher A. Rice, Nathan D. Haluska

Published Feb 15, 2018• 0 citations
Publisher

Abstract

We report the first CW lasing from two-photon pumping via a virtual state. Pulsed and the CW lasing of the 3096 nm 72 P1/2 to 72 S1/2 line are observed from degenerate two-photon pumping of the cesium 72 S1/2 to 62 D3/2 transition. High intensity pulses excite over 17 lasing wavelengths. Under lower intensity CW excitation, 3 μm lasing is still observed with efficiencies of 0.7%. CW experiments utilized a Cs heat pipe at 150 °C to 270 °C, and a highly-focused, single pass, Ti-Sapphire pump with no aid of a cavity. Unlike normal DPALS, this architecture does not require buffer gas, and heat is released optically so a flowing system is not required. Both suggest a very simple device with excellent beam quality is possible. This proof of concept can be greatly enhanced with more optimal conditions such as non-degenerate pumping to further increase the two-photon pump cross section and the addition of a cavity to improve mode volume overlap. These improvements may lead to an increase in efficiencies to a theoretical maximum of 14%. Results suggest two-photon pumping with diodes is feasible.

DOI
10.1117/12.2290407

Related papers

Efficient non-linear two-photon effects from the Cesium 6D manifold

Glen P. Perram, Nathan D. Haluska, Christopher A. Rice

We report several non-linear process that occur when two-photon pumping the cesium 6D states. Cesium vapor possess some of the largest two-photon pump cross sections in nature. Pumping these cross sections leads to strong amplified spontaneous emission that we observe on over 17 lasing lines. These new fields are strong enough to couple with the pump to create additional tunable lines. We use a heat pipe with cesium densities of 1014 to 1016 cm-3 and 0 to 5 Torr of helium buffer gas. The cesium 6D States are interrogated by both high energy pulses and low power CW sources. We observe four-wave mixing, six-wave mixing, potential two-photon lasing, other unknown nonlinear processes, and the persistence of some processes at low thresholds. This system is also uniquely qualified to support two-photon lasing under the proper conditions.

Nonlinear Frequency Generation and Conversion: Materials and Devices•Feb 15, 2018•4 citations

Continuous-Wave Mirrorless Lasing at 1.47 µm in Blue-Light Pumped Cs Vapor

Tiantian Shi, Jianxiang Miao, Jingbiao Chen

Population inversion on the 7S1/2− 6P3/2transition of cesium atoms is built by 455 nm diode laser pumping, and continuous-wave (cw) lasing is observed without the feedback on the gain medium from cavity mirrors. The stimulated emission at 1.47 µm infrared wavelength is restricted to a narrow angle along the direction of propagation of the pumping laser. Evidence of threshold-like characteristic is demonstrated in the cw mirrorless lasing dependence on pumping laser detuning, atomic density, and pumping light intensity. This compact structure can be used to generate mirrorless laser in a number of infrared wavelengths applied for the communication area. Moreover, it is expected to realize the narrow-linewidth optical frequency standard from an ultralow-finesse optical cavity.

Joint Conference of the European Frequency and Time Forum and IEEE International Frequency Control Symposium (EFTF/IFCS)•Jul 7, 2021•0 citations

Wavelength diversity in optically pumped alkali vapor lasers

Glen P. Perram

Alternative wavelengths for optically pumped alkali vapor lasers have been developed using single photon excitation of higher lying P-states, stimulated Raman processes, two-photon excitation of S and D states, and electric quadruple excitation on S-D transitions. Two photon excitation of Cs 72D leads to competing and cascade lasing producing red and infrared lasers operating on the D-P transitions, followed by ultraviolet, blue, the standard near infrared DPAL transitions operating on P-S transitions. The S-D pump transitions are fully bleached at pump intensities exceeding 1 MW/cm2, allowing for lasing transitions that terminate on the ground state. The kinetics of these systems are complex due to competition for population inversion among the many optical transitions. An optically pumped mid-infrared rubidium pulsed, mirrorless laser has also been demonstrated in a heat pipe along both the 62P3/2 - 62S1/2 transition at 2.73 μm and the 62P1/2 - 62S1/2 transition at 2.79 μm with a maximum energy of ~100 nJ. Performance improves dramatically as the rubidium vapor density is increased, in direct contradiction with the prior work. No scaling limitations associated with energy pooling or ionization kinetics have been observed. Practical application for infrared counter measures depends on the further development of blue diode pump sources. Finally, stimulated electronic Raman scattering and hyper-Raman processes in potassium vapor near the D1 and D2 lines have been observed using a stable resonator and pulsed laser excitation. First and second order Stokes and anti-Stokes lines were observed simultaneously and independently for a pump laser tuning range exceeding 70 cm-1. When the pump is tuned between the K D1 and D2 lines, an efficient hyper-Raman process dominates with a slope efficiency that exceeds 10%. Raman shifted laser may be useful as a target illuminator or atmospheric compensation beacon for a high power diode pumped alkali laser.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jan 13, 2017•1 citation

Determining the Two-Photon Absorption Cross-Section for the 52S1/2 --> 52D5/2 Transition in Naturally Occurring Rubidium

Jeffrey Gallagher, Glen P. Perram

Recently we demonstrated lasing at 420 nm and 455 nm inside of rubidium and cesium vapor cells respectively, by non-resonant, two photon absorption at near infrared pump wavelengths. Two photon absorption from the ground S1/2 state to excited D3/2,5/2 or higher lying S1/2 state via virtual states and subsequent infrared stimulated emission pumps the upper laser levels, the second excited P1/2,3/2 states. To better understand the mechanism and phenomenology of this type of laser, this paper presents a method for determining the two-photon absorption (TPA) cross-section for the 5S1/2 −→ 5D5/2 transition in naturally occurring rubidium. For an incident pump intensity of 392 W cm2 and a rubidium concentration of 3.34 × 10 atoms cm3 , a peak absorbance of 0.10 is observed. The concentration of the Rb in the test cell is determined by one photon absorption spectra of the D2, indicating a vapor curve shifted by 14 C from the exterior wall temperature. The incident laser beam is focused to a waist of 75 μm. The beam quality is consistent with an M = 1.05 − 1.09. A model for the intensity as a function of propagation distance is developed to interpret the observed absorption spectrum and determine a cross-section for the two photon absorption.

AIAA Plasmadynamics and Lasers Conference•Jun 1, 2011•1 citation

Ultraviolet and blue stimulated emission from Cs alkali vapor pumped using two-photon absorption and four-wave mixing

Ricardo C. Davila, Christopher A. Rice, Nathan B. Terry +1 more

Stimulated emission on the ultraviolet and blue transitions in Cs has been achieved by pumping via two-photon absorption and four-wave mixing for the pump transition 62S12→82D32,52. The emission performance of the optically pumped cesium vapor laser operating in ultraviolet and blue has been extended to 650 nJ/pulse for 387 nm, 1 to 3 μJ/pulse for 388 nm, 200 nJ/pulse for 455 nm, and 500 nJ/pulse for 459 nm. Emission performance improves dramatically as the cesium vapor density is increased, and no scaling limitations associated with energy pooling or ionization kinetics have been observed.

Optical Engineering•Dec 9, 2024•0 citations

Multi-photon processes in alkali metal vapors

Baodong Gai, Shu Hu, Hui Li +7 more

Achieving population inversion through multi-photon cascade pumping is almost always difficult, and most laser medium work under 1-photon excitation mechanism. But for alkali atoms such as cesium, relatively large absorption cross sections of several low, cascading energy levels enable them properties such as up conversion. Here we carried out research on two-photon excitation alkali fluorescence. Two photons of near infrared region are used to excite alkali atoms to n 2 D5/2, n 2 D3/2 or higher energy levels, then the blue fluorescence of (n+1) 2 P3/2,(n+1) 2 P1/2→n 2 S1/2 are observed. Different pumping paths are tried and by the recorded spectra, transition routes of cesium are deducted and concluded. Finally the possibility of two-photon style DPALs (diode pumped alkali laser) are discussed, such alkali lasers can give output wavelengths in the shorter end of visual spectroscopy (400-460 nm) and are expected to get application in underwater communication and material laser processing.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Feb 3, 2015•0 citations
We report the first CW lasing from two-photon pumping via a virtual state. Pulsed and the CW lasing of the 3096 nm 72 P1/2 to 72 S1/2 line are observed from degenerate two-photon pumping of the cesium 72 S1/2 to 62 D3/2 transition. High intensity pulses excite over 17 lasing wavelengths. Under lower intensity CW excitation, 3 μm lasing is still observed with efficiencies of 0.7%. CW experiments utilized a Cs heat pipe at 150 °C to 270 °C, and a highly-focused, single pass, Ti-Sapphire pump with no aid of a cavity. Unlike normal DPALS, this architecture does not require buffer gas, and heat is released optically so a flowing system is not required. Both suggest a very simple device with excellent beam quality is possible. This proof of concept can be greatly enhanced with more optimal conditions such as non-degenerate pumping to further increase the two-photon pump cross section and the addition of a cavity to improve mode volume overlap. These improvements may lead to an increase in efficiencies to a theoretical maximum of 14%. Results suggest two-photon pumping with diodes is feasible.
We report several non-linear process that occur when two-photon pumping the cesium 6D states. Cesium vapor possess some of the largest two-photon pump cross sections in nature. Pumping these cross sections leads to strong amplified spontaneous emission that we observe on over 17 lasing lines. These new fields are strong enough to couple with the pump to create additional tunable lines. We use a heat pipe with cesium densities of 1014 to 1016 cm-3 and 0 to 5 Torr of helium buffer gas. The cesium 6D States are interrogated by both high energy pulses and low power CW sources. We observe four-wave mixing, six-wave mixing, potential two-photon lasing, other unknown nonlinear processes, and the persistence of some processes at low thresholds. This system is also uniquely qualified to support two-photon lasing under the proper conditions.
Population inversion on the 7S1/2− 6P3/2transition of cesium atoms is built by 455 nm diode laser pumping, and continuous-wave (cw) lasing is observed without the feedback on the gain medium from cavity mirrors. The stimulated emission at 1.47 µm infrared wavelength is restricted to a narrow angle along the direction of propagation of the pumping laser. Evidence of threshold-like characteristic is demonstrated in the cw mirrorless lasing dependence on pumping laser detuning, atomic density, and pumping light intensity. This compact structure can be used to generate mirrorless laser in a number of infrared wavelengths applied for the communication area. Moreover, it is expected to realize the narrow-linewidth optical frequency standard from an ultralow-finesse optical cavity.
Alternative wavelengths for optically pumped alkali vapor lasers have been developed using single photon excitation of higher lying P-states, stimulated Raman processes, two-photon excitation of S and D states, and electric quadruple excitation on S-D transitions. Two photon excitation of Cs 72D leads to competing and cascade lasing producing red and infrared lasers operating on the D-P transitions, followed by ultraviolet, blue, the standard near infrared DPAL transitions operating on P-S transitions. The S-D pump transitions are fully bleached at pump intensities exceeding 1 MW/cm2, allowing for lasing transitions that terminate on the ground state. The kinetics of these systems are complex due to competition for population inversion among the many optical transitions. An optically pumped mid-infrared rubidium pulsed, mirrorless laser has also been demonstrated in a heat pipe along both the 62P3/2 - 62S1/2 transition at 2.73 μm and the 62P1/2 - 62S1/2 transition at 2.79 μm with a maximum energy of ~100 nJ. Performance improves dramatically as the rubidium vapor density is increased, in direct contradiction with the prior work. No scaling limitations associated with energy pooling or ionization kinetics have been observed. Practical application for infrared counter measures depends on the further development of blue diode pump sources. Finally, stimulated electronic Raman scattering and hyper-Raman processes in potassium vapor near the D1 and D2 lines have been observed using a stable resonator and pulsed laser excitation. First and second order Stokes and anti-Stokes lines were observed simultaneously and independently for a pump laser tuning range exceeding 70 cm-1. When the pump is tuned between the K D1 and D2 lines, an efficient hyper-Raman process dominates with a slope efficiency that exceeds 10%. Raman shifted laser may be useful as a target illuminator or atmospheric compensation beacon for a high power diode pumped alkali laser.
Recently we demonstrated lasing at 420 nm and 455 nm inside of rubidium and cesium vapor cells respectively, by non-resonant, two photon absorption at near infrared pump wavelengths. Two photon absorption from the ground S1/2 state to excited D3/2,5/2 or higher lying S1/2 state via virtual states and subsequent infrared stimulated emission pumps the upper laser levels, the second excited P1/2,3/2 states. To better understand the mechanism and phenomenology of this type of laser, this paper presents a method for determining the two-photon absorption (TPA) cross-section for the 5S1/2 −→ 5D5/2 transition in naturally occurring rubidium. For an incident pump intensity of 392 W cm2 and a rubidium concentration of 3.34 × 10 atoms cm3 , a peak absorbance of 0.10 is observed. The concentration of the Rb in the test cell is determined by one photon absorption spectra of the D2, indicating a vapor curve shifted by 14 C from the exterior wall temperature. The incident laser beam is focused to a waist of 75 μm. The beam quality is consistent with an M = 1.05 − 1.09. A model for the intensity as a function of propagation distance is developed to interpret the observed absorption spectrum and determine a cross-section for the two photon absorption.
Stimulated emission on the ultraviolet and blue transitions in Cs has been achieved by pumping via two-photon absorption and four-wave mixing for the pump transition 62S12→82D32,52. The emission performance of the optically pumped cesium vapor laser operating in ultraviolet and blue has been extended to 650 nJ/pulse for 387 nm, 1 to 3 μJ/pulse for 388 nm, 200 nJ/pulse for 455 nm, and 500 nJ/pulse for 459 nm. Emission performance improves dramatically as the cesium vapor density is increased, and no scaling limitations associated with energy pooling or ionization kinetics have been observed.
Achieving population inversion through multi-photon cascade pumping is almost always difficult, and most laser medium work under 1-photon excitation mechanism. But for alkali atoms such as cesium, relatively large absorption cross sections of several low, cascading energy levels enable them properties such as up conversion. Here we carried out research on two-photon excitation alkali fluorescence. Two photons of near infrared region are used to excite alkali atoms to n 2 D5/2, n 2 D3/2 or higher energy levels, then the blue fluorescence of (n+1) 2 P3/2,(n+1) 2 P1/2→n 2 S1/2 are observed. Different pumping paths are tried and by the recorded spectra, transition routes of cesium are deducted and concluded. Finally the possibility of two-photon style DPALs (diode pumped alkali laser) are discussed, such alkali lasers can give output wavelengths in the shorter end of visual spectroscopy (400-460 nm) and are expected to get application in underwater communication and material laser processing.