The physical constraints underlying the concept of quantum circuit are considered. In particular it is shown that the point of departure for their modeling starts from the interconnection of the components into a classical network, followed by quantization of the latter, and not by the interconnection of already quantized components. The procedure is straightforward for lossless networks but cannot be worked out in presence of resistors for the impossibility of constructing a Lagrangian function. However the difficulty is circumvented by distinguishing thermal from radiative resistors, the former being the usual ones, the latter being realized by semi-infinite LC transmission lines, for which the Lagrangian exists. In the complex plane s = σ + jω the impedance of a thermal resistor is Z(s) = R in the entire plane while that of a radiative resistor is Rsign(σ), so that the latter is lossless and does not dissipate energy but conveys it to the infinity. Comparison with Lindblad approach shows that the resistor fits into it in the RHP. Radiative resistors make evolution reversible, which is not true for a physical system including thermal.
Abstract Superconducting circuits are one of the leading quantum platforms for quantum technologies. With growing system complexity, it is of crucial importance to develop scalable circuit models that contain the minimum information required to predict the behaviour of the physical system. Based on microwave engineering methods, divergent and non-divergent Hamiltonian models in circuit quantum electrodynamics have been proposed to explain the dynamics of superconducting quantum networks coupled to infinite-dimensional systems, such as transmission lines and general impedance environments. Here, we study systematically common linear coupling configurations between networks and infinite-dimensional systems. The main result is that the simple Lagrangian models for these configurations present an intrinsic natural length that provides a natural ultraviolet cutoff. This length is due to the unavoidable dressing of the environment modes by the network. In this manner, the coupling parameters between their components correctly manifest their natural decoupling at high frequencies. Furthermore, we show the requirements to correctly separate infinite-dimensional coupled systems in local bases. We also compare our analytical results with other analytical and approximate methods available in the literature. Finally, we propose several applications of these general methods to analogue quantum simulation of multi-spin-boson models in non-perturbative coupling regimes.
Abstract The quantization of systems composed of transmission lines connected to lumped circuits poses significant challenges, arising from the interaction between continuous and discrete degrees of freedom. A widely adopted strategy, based on the pioneering work of Yurke and Denker, entails representing the lumped circuit contributions using Lagrangian densities that incorporate Dirac δ-functions. However, this approach introduces complications, as highlighted in the recent literature, including divergent momentum densities, necessitating the use of regularization techniques. In this work, we introduce a δ-free Lagrangian formulation for a transmission line capacitively coupled to a lumped circuit without the need for a discretization of the transmission line or mode expansions. This is achieved by explicitly enforcing boundary conditions at the line ends in the principle of least action. In this framework, the quantization and the derivation of the Heisenberg equations of the network are straightforward. We obtain a reduced model for the lumped circuit in the quantum Langevin form, which is valid for any coupling strength between the line and the lumped circuit. We apply our approach to an analytically solvable network consisting of a semi-infinite transmission line capacitively coupled to an LC circuit and study the behavior of the network as the coupling strength varies.
During the last 30 years, stimulated by the quest to build superconducting quantum processors, a theory of quantum electrical circuits has emerged, which is called circuit quantum electrodynamics or circuit-QED. The goal of the theory is to provide a quantum description of the most relevant degrees of freedom. The central objects to be derived and studied are the Lagrangian and the Hamiltonian governing these degrees of freedom. Central concepts in classical network theory such as impedance and scattering matrices can be used to obtain the Hamiltonian and Lagrangian description for the lossless (linear) part of the circuits. Methods of analysis, both classical and quantum, can also be developed for nonreciprocal circuits. These lecture notes aim at giving a comprehensive, theoretically oriented, overview of this subject for Master or PhD students in physics and electrical engineering.
We discuss the introduction of constraints in a system of n noninteracting particles which obey the laws of nonrelativistic quantum mechanics. In this paper the particles are first thought of as being unconstrained (described by the
3n Cartesian coordinates of a flat space
R), but subject to an external potential
V which, in a certian suitable limit, forces the system to remain in a curved subspace
V of
R. This idea was already employed in a previous work where we have discussed the motion of one constrained particle. It was then shown that in order to obtain a meaningful result the particle wave function should be "uniformly compressed" into a surface (or curve), avoiding, in this way, the tangential forces which correspond to the dissipative constraints of classical mechanics. The resulting Schr\"odinger equation could then be separated in such a way that the part which contained the surface (or curve) variables was independent of the potential
V employed in the constraining process. In the present paper we show that this procedure cannot be carried out for all subspaces
V of
R in the case of a many-particle system, unless
V satisfies a certain geometrical condition. The many-particle Schr\"odinger equation (as was already the case of the one-particle systems) contains, besides the kinetic energy term, potentials which are not bending invariants, that is, cannot be obtained from the metric tensor
gij of
V or its derivatives. This gives rise to different Schr\"odinger equations for isometric subspaces, in striking contrast with the usual quantization procedures which start from the classical Lagrangian of the constrained system.
Abstract The importance of dissipation engineering ranges from universal quantum computation to non‐equilibrium quantum thermodynamics. In recent years, more and more theoretical and experimental studies have shown the relevance of this topic for circuit quantum electrodynamics, one of the major platforms in the race for a quantum computer. This article discusses how to simulate thermal baths by inserting resistive elements in networks of superconducting qubits. Apart from pedagogically reviewing the phenomenological and microscopic models of a resistor as thermal bath with Johnson–Nyquist noise, the paper introduces some new results in the weak coupling limit, showing that the most common examples of open quantum systems can be simulated through capacitively coupled superconducting qubits and resistors. The aim of the manuscript, written with a broad audience in mind, is to be both an instructive tutorial about how to derive and characterize the Hamiltonian of general dissipative superconducting circuits with capacitive coupling, and a review of the most relevant and topical theoretical and experimental works focused on resistive elements and dissipation engineering.
We propose a new quantization method for superconducting electronic circuits involving a Josephson-junction device coupled to a linear microwave environment. The method is based on an exact impedance synthesis of the microwave environment considered as a blackbox with impedance function
Z(s). The synthesized circuit captures dissipative dynamics of the system with resistors coupled to the reactive part of the circuit in a nontrivial way. We quantize the circuit and compute relaxation rates following previous formalisms for lumped element circuit quantization. Up to the errors in the fit our method gives an exact description of the system and its losses.