The residual amplitude modulation (RAM) is a spurious effect of the phase modulation in the laser beam power. In this work we show that the optical modulators that are used to generate the sidebands on the laser beam generate a RAM that should be regarded as a fundamental level of noise in the optical setup.
Residual amplitude modulation (RAM) is an unwanted noise source in electro-optic phase modulators. The analysis presented shows that while the magnitude of the RAM produced by a MgO:LiNbO(3) modulator increases with intensity, its associated phase becomes less well defined. This combination results in temporal fluctuations in RAM that increase with intensity. This behavior is explained by the presented phenomenological model based on gradually evolving photorefractive scattering centers randomly distributed throughout the optically thick medium. This understanding is exploited to show that RAM can be reduced to below the 10(-5) level by introducing an intense optical beam to erase the photorefractive scatter.
We present an analysis on how the optical parametric oscillator (OPO) detuning and the relative phase drift deteriorate the stability of the squeezed states, including the output power and the squeezed degree, and investigate the influence of RAM on the cavity detuning and the relative phase drift under different cases. Subsequently, the RAM is experimentally measured. In term of the measurement results, we perform a comparative study about RAM's influence on the cavity and phase locking in two cases. As a result, with the error signal extracted from the transmission of the OPO, the output power stability of the squeezed light is greatly improved. With the phase modulation imposed on the signal beam, the long-term stability of the squeezed degree is significantly enhanced.
A novel phase-modulation technique which permits subkilohertz-laser stability and new levels of precision in laser spectroscopy was reported recently. For spectroscopy, the basic arrangement consists of a combination of an optical pump and a probe field which is phase modulated. The pump prepares the atomic sample by burning a narrow hole within the atom's inhomogeneous line shape, and the probe beam samples the prepared hole when its modulation sidebands are swept into resonance. Off resonance, the probe is balanced as pairs of sidebands produce heterodyne beat signals of opposite phase which just cancel. On resonance, the balance is upset and yields a nonvanishing beat signal with a Lorentzian absorption or dispersion line shape and with residual noise approaching the shot noise limit. Here we investigate the theory of phase-modulation spectroscopy. We treat the nonlinear response of an atomic two-level quantum system subject to an intense pump and a weak copropagating or counterpropagating phase-modulated probe beam. The density-matrix equations of motion are solved by a Laplace-transform method and by the novel use of a translation operator which allows the infinite hierarchy of coupled equations to close. A solution equivalent to the rate-equation result is developed and coherence corrections are found which predict new resonances that have just been detected in this laboratory. The delayed pump-probe technique encountered in solid-state laser spectroscopy is analyzed in this context for two- and three-level quantum systems. The response of a Fabry-Perot cavity to a phase-modulated light wave is examined also and reveals an unexpected absorption feature.
Residual amplitude modulation is one of the major sources of instability in ultra-sensitive optical detections based on frequency modulation. Using a MgO·LiNbO(3) electro-optic crystal, we systematically measure the temperature and polarization dependence of residual amplitude modulation and our experimental results are in good agreement with a previous theoretical analysis. After optical phase modulation, two independent arms including optical detection and frequency demodulation are employed to closely examine the instability of the residual amplitude modulation. Residual amplitude modulation below 25 ppm is obtained with an active cancellation scheme in which the crystal temperature is varied so as to zero the baseline drifts with different origins. Possible improvements for better suppression and stability are discussed.
Residual amplitude modulation is one of the major stability-degrading factors in many precision measurements. Using an electro-optic (EO) crystal with wedged input and output surfaces is an effective way to suppress residual amplitude modulation. Here the mechanism of residual amplitude modulation in this approach is investigated. The residual amplitude modulations measured in standard and wedged EO crystals bear similarities in their temperature and polarization dependences, implying that a mixture of the two orthogonal polarizations in the extraordinary light is responsible for the residual amplitude modulation in the wedged EO crystal. Similar to a standard EO crystal, a non-uniform spatial distribution of residual amplitude modulation is also observed in the extraordinary light emerging from the wedged EO crystal. The optical isolator after the EO crystal is replaced by a Faraday rotator, and an improvement in the long-term stability is observed. With the wedged-crystal approach, residual amplitude modulation as low as 2×10−7 is observed, contributing a frequency instability of 8×10−18 (500 s) in Pound–Drever–Hall frequency stabilization with a discrimination slope of 1×10−4 V/Hz.