Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

A Time-Domain SQUID Multiplexer System for Read-Out of Superconducting Transition-Edge-Sensor Arrays

C. D. Reintsema, James A. Beall, Steven W. Deiker, William Bertrand Doriese, Gene C Hilton, K. D. Irwin, Sae Woo Nam, Leila R. Vale, Joel N. Ullom, Yizi Xu, Joern Beyer, M. E. Huber

Published Jul 7, 2003• 1 citation
OpenAlex

Related papers

A Scalable Readout for Microwave SQUID Multiplexing of Transition-Edge Sensors

Johnathon D. Gard, Daniel Becker, D. A. Bennett +7 more

Journal of Low Temperature Physics•Jul 9, 2018•33 citations

SQUID-Based Multiplexers for Transition Edge Sensor Readout

M. Kiviranta, Heikki Seppä, Jan van der Kuur +1 more

•Jan 1, 2002•0 citations

SQUID multiplexers for transition-edge sensors

K. D. Irwin

Physica C Superconductivity•Mar 1, 2002•124 citations

Time-Division SQUID Multiplexers for Transition-Edge Sensors | NIST

K. D. Irwin, James A. Beall, Joern Beyer +8 more

•Jan 14, 2003•0 citations

Development of the Microwave SQUID Multiplexer for an X-ray Microcalorimeter Array of Transition Edge Sensor

悠喜 今井

•Jan 1, 2022•0 citations

A frequency-domain SQUID multiplexer for arrays of transition-edge superconducting sensors

Trevor M. Lanting, Hsiao-Mei Cho, John L. Clarke +5 more

We describe the development of a frequency-domain multiplexer (MUX) to read out arrays of superconducting transition-edge sensors (TES). Fabrication of large-format arrays of these sensors is becoming practical; however, reading out each sensor in the array is a major instrumental challenge. Frequency-domain multiplexing can greatly simplify the instrumentation of large arrays by reducing the number of SQUID's (superconducting quantum interference devices) and wires to the low temperature stages. Each sensor is AC biased at a different frequency, ranging from 380 kHz to 1 MHz. Each sensor signal amplitude-modulates its respective AC bias frequency. An LC filter associated with each sensor suppresses Johnson noise from the other sensors. The signals are combined at a current summing node and measured by a single SQUID. The individual signals from each sensor are then lock-in detected by room temperature electronics. Test chips with fully lithographed LC filters for up to 32 channels have been designed and fabricated. The capacitance and inductance values have been measured and are close to the design goals. We discuss the basic principles of frequency-domain multiplexing, the design and testing of the test chips, and the implementation of a practical system.

IEEE Transactions on Applied Superconductivity•Jun 1, 2003•20 citations
We describe the development of a frequency-domain multiplexer (MUX) to read out arrays of superconducting transition-edge sensors (TES). Fabrication of large-format arrays of these sensors is becoming practical; however, reading out each sensor in the array is a major instrumental challenge. Frequency-domain multiplexing can greatly simplify the instrumentation of large arrays by reducing the number of SQUID's (superconducting quantum interference devices) and wires to the low temperature stages. Each sensor is AC biased at a different frequency, ranging from 380 kHz to 1 MHz. Each sensor signal amplitude-modulates its respective AC bias frequency. An LC filter associated with each sensor suppresses Johnson noise from the other sensors. The signals are combined at a current summing node and measured by a single SQUID. The individual signals from each sensor are then lock-in detected by room temperature electronics. Test chips with fully lithographed LC filters for up to 32 channels have been designed and fabricated. The capacitance and inductance values have been measured and are close to the design goals. We discuss the basic principles of frequency-domain multiplexing, the design and testing of the test chips, and the implementation of a practical system.