Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

The Japan Society of Applied Physics

Improvement of dielectric loss in superconducting microwave resonators

Wei Qiu

Published Jul 8, 2014• 0 citations
OpenAlex

Related papers

Dielectric Loss in Superconducting Microwave Resonators

圭正 牧瀬, 弘高 寺井, Hirotaka Terai

IEICE Technical Report; IEICE Tech. Rep.•Apr 15, 2015•0 citations

Investigation of Dielectric Losses in Hydrogenated Amorphoussilicon (a-Si:H) thin Films Using Superconducting Microwave Resonators

Alessandro Bruno, Sebastian T. Skacel, Ch. Kaiser +4 more

The improvement of the coherence times of superconducting qubits depends on the reduction of the dielectric losses in the insulating materials implemented for the device fabrication. These losses depend on the density of spurious dipoles of different nature (two-level systems, TLSs) which couple to phase qubits and, hence, limit their coherence times. Hydrogenated amorphous silicon (a-Si:H), because of its lower loss tangent (tan δ) among conventional dielectrics (a-SiO, a-SiO2, a-SiNx:H), is considered as the best amorphous dielectric for superconducting qubit application. We have developed a reliable method for the direct measurement of dielectric losses in amorphous dielectric thin films using a novel design based on four lumped superconducting LC resonators connected in series without coupling capacitors. The losses are obtained as tan δ = 1/Q0, where Q0 is the intrinsic quality factor of the resonator, measured at 3 dB above the resonance frequency without any fitting procedure. The series type LC resonators with a-Si:H as dielectric were fabricated by the Nb technology. The measurements were done at the conditions of a qubit application (0.5 -10 GHz frequency range and low temperatures). The low values of the loss tangent of a-Si:H (up to 2.5 x 10−5 at 4.2 K) have required the development of superconducting housing for the resonators in order to eliminate a spurious dependence of tan δ on the microwave power, by reducing losses which were not originated in the dielectric itself. The results of the simulations agree well with the experiments.

Physics Procedia•Jan 1, 2012•8 citations

Superconducting Microwave Resonators

Charles Neill, A. Megrant, M. Lenander +17 more

Bulletin of the American Physical Society•Mar 1, 2012•0 citations

Microwave Loss in Josephson Junction Embedded Superconducting Resonators

Steven J. Weber, Kater W. Murch, Irfan A. Siddiqi

Bulletin of the American Physical Society•Mar 1, 2012•0 citations

Vacuum-Gap Capacitors for Low-Loss Superconducting Resonant Circuits

Katarina Cicak, Michael S. Allman, Joshua Strong +2 more

Low-loss microwave components are used in many superconducting resonant circuits from multiplexed readouts of low-temperature detector arrays to quantum bits. Two-level system defects in amorphous dielectric materials cause excess energy loss. In an effort to improve capacitor components, we have used optical lithography and micromachining techniques to develop superconducting parallel-plate capacitors in which lossy dielectrics are replaced by vacuum gaps. Resonance measurements at 50 mK on lumped LC circuits that incorporate these vacuum-gap capacitors (VGCs) reveal loss tangents at low powers as low as$4\times 10^{-5}$, significantly lower than with capacitors using amorphous dielectrics. VGCs are structurally robust, small, and easily scaled to capacitance values above 100 pF.

arXiv:0810.1976•IEEE Transactions on Applied Superconductivity•Jun 1, 2009•19 citations

Simulation of Superconducting Microwave Resonators

Antti Jokiluoma

•May 17, 2015•0 citations
The improvement of the coherence times of superconducting qubits depends on the reduction of the dielectric losses in the insulating materials implemented for the device fabrication. These losses depend on the density of spurious dipoles of different nature (two-level systems, TLSs) which couple to phase qubits and, hence, limit their coherence times. Hydrogenated amorphous silicon (a-Si:H), because of its lower loss tangent (tan δ) among conventional dielectrics (a-SiO, a-SiO2, a-SiNx:H), is considered as the best amorphous dielectric for superconducting qubit application. We have developed a reliable method for the direct measurement of dielectric losses in amorphous dielectric thin films using a novel design based on four lumped superconducting LC resonators connected in series without coupling capacitors. The losses are obtained as tan δ = 1/Q0, where Q0 is the intrinsic quality factor of the resonator, measured at 3 dB above the resonance frequency without any fitting procedure. The series type LC resonators with a-Si:H as dielectric were fabricated by the Nb technology. The measurements were done at the conditions of a qubit application (0.5 -10 GHz frequency range and low temperatures). The low values of the loss tangent of a-Si:H (up to 2.5 x 10−5 at 4.2 K) have required the development of superconducting housing for the resonators in order to eliminate a spurious dependence of tan δ on the microwave power, by reducing losses which were not originated in the dielectric itself. The results of the simulations agree well with the experiments.
Low-loss microwave components are used in many superconducting resonant circuits from multiplexed readouts of low-temperature detector arrays to quantum bits. Two-level system defects in amorphous dielectric materials cause excess energy loss. In an effort to improve capacitor components, we have used optical lithography and micromachining techniques to develop superconducting parallel-plate capacitors in which lossy dielectrics are replaced by vacuum gaps. Resonance measurements at 50 mK on lumped LC circuits that incorporate these vacuum-gap capacitors (VGCs) reveal loss tangents at low powers as low as4×10−54\times 10^{-5}4×10−5, significantly lower than with capacitors using amorphous dielectrics. VGCs are structurally robust, small, and easily scaled to capacitance values above 100 pF.