Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Bulletin of the American Physical Society

Microfabrication of low-loss lumped-element Josephson circuits for non-reciprocal and parametric devices

Katarina Cicak, Florent Lecocq, Leonardo Ranzani, G. A. Peterson, Shlomi Kotler, John D. Teufel, Raymond W. Simmonds, José Aumentado

Published Mar 17, 2017• 0 citations
OpenAlex

Related papers

Design and operation of a broadband Josephson parametric amplifier based on lumped elements

Ilari Lilja

•Oct 18, 2018•0 citations

Development of a lumped element Josephson parametric amplifier for frequencies below 1 GHz

Ilmo Räisänen

•May 12, 2015•0 citations

Josephson traveling-wave parametric amplifier based on a low-intrinsic-loss lumped-element coplanar waveguide

C. W. Sandbo Chang, Arjan F. van Loo, Chih-Chiao Hung +4 more

Josephson traveling-wave parametric amplifiers (JTWPAs) are key to fast, frequency-multiplexed measurements in superconducting circuits. JTWPAs with periodic modulation are attractive, as they phase match without flux or dc bias, but they often suffer from significant gain ripples. Another common limitation in JTWPAs is intrinsic loss, which has prevented them from reaching the quantum limit of added noise. Here researchers address both issues by implementing an all-aluminum coplanar lumped-element JTWPA, using a qubit-compatible fabrication recipe. Their modulated device suppresses gain ripples for smooth, bias-free amplification, and approaches the quantum limit of added noise.

arXiv:2503.07559•Physical Review Applied•Sep 23, 2025•9 citations

Lumped, Single-ended Josephson Parametric Converters for Hamiltonian Engineering

Tzu-Chiao Chien, Katarina Cicak, Florent Lecocq +7 more

Bulletin of the American Physical Society•Mar 7, 2019•0 citations

Low-loss lumped-element inductors made from granular aluminum

Vishakha Gupta, Patrick Winkel, Neel Thakur +5 more

Lumped-element inductors are an integral component in the circuit QED toolbox. However, it is challenging to build inductors that are simultaneously compact, linear, and low-loss with standard approaches that either rely on the geometric inductance of superconducting thin films or on the kinetic inductance of Josephson-junction arrays. In this work, we overcome this challenge by utilizing the high kinetic inductance offered by superconducting granular aluminum (grAl). We demonstrate lumped-element inductors with a few nH of inductance that are up to 100 times shorter than inductors built from pure aluminum (Al). To characterize the properties of these linear inductors, we first report on the performance of lumped-element resonators built entirely out of grAl with sheet inductances varying from 30 – 320 pH/sq and self-Kerr nonlinearities of 0.2 – 20 Hz / photon . Further, we demonstrate integration of these grAl inductors into hybrid resonators with Al or tantalum ( Ta ) capacitor electrodes without increasing total internal losses. Interestingly, the measured internal quality factors systematically decrease with increasing room-temperature resistivity of the grAl film for all devices, indicating a trade-off between compactness and internal loss. For our lowest resistivity grAl films, we measure quality factors reaching 3.5 × 10 6 for the all-grAl devices and 4.5 × 10 6 for the hybrid grAl/ Ta devices, similar to state-of-the-art quantum circuits. Our loss analysis suggests that the surface-loss factor of grAl is similar to that of pure Al for our lowest resistivity films, while the increasing losses with resistivity could be explained by increasing inductor loss in the grAl film.

arXiv:2411.12611•Physical Review Applied•May 27, 2025•24 citations

Development of Josephson Parametric Amplifiers for quantum applications

Stefanos Basili

Quantum-limited parametric amplifiers have become increasingly interesting and relevant with the progressing field of quantum computing. However, currently it is still challenging to fabricate these complex devices. In this thesis, we developed cross type Josephson junctions (JJs), lumped element LC resonators, lumped element Josephson parametric amplifiers (JPAs) and Josephson traveling wave parametric amplifiers (JTWPAs). We found and resolved several fabrication issues however we suspect that both the JPA and JTWPA suffered from microshorts in the circuits during the cryogenic measurements. Nevertheless, we managed to measure the resonance frequency of the JPA and have noticed the flux focusing effect when we flux tune it. We preformed room temperature measurements on over 300 JJs and calculated the relative standard deviation (RSD) for various JJ sizes. We found the spread of 30 fabricated resonators and a rough estimate of their Q factors. The JTWPAs developed are non-degenerate four wave mixing amplifiers that use the resonant phase matching (RPM) technique to reduce the phase mismatch problem. The transmission through the measured JTWPA showed 50 dB loss probably caused by presumably a short from the transmission line to ground. However, when the JTWPA was driven with a pump we observed 20 dB increase in transmission in some frequency bands.

•Jan 1, 2020•0 citations
Josephson traveling-wave parametric amplifiers (JTWPAs) are key to fast, frequency-multiplexed measurements in superconducting circuits. JTWPAs with periodic modulation are attractive, as they phase match without flux or dc bias, but they often suffer from significant gain ripples. Another common limitation in JTWPAs is intrinsic loss, which has prevented them from reaching the quantum limit of added noise. Here researchers address both issues by implementing an all-aluminum coplanar lumped-element JTWPA, using a qubit-compatible fabrication recipe. Their modulated device suppresses gain ripples for smooth, bias-free amplification, and approaches the quantum limit of added noise.
Lumped-element inductors are an integral component in the circuit QED toolbox. However, it is challenging to build inductors that are simultaneously compact, linear, and low-loss with standard approaches that either rely on the geometric inductance of superconducting thin films or on the kinetic inductance of Josephson-junction arrays. In this work, we overcome this challenge by utilizing the high kinetic inductance offered by superconducting granular aluminum (grAl). We demonstrate lumped-element inductors with a few nH of inductance that are up to 100 times shorter than inductors built from pure aluminum (Al). To characterize the properties of these linear inductors, we first report on the performance of lumped-element resonators built entirely out of grAl with sheet inductances varying from 30 – 320 pH/sq and self-Kerr nonlinearities of 0.2 – 20 Hz / photon . Further, we demonstrate integration of these grAl inductors into hybrid resonators with Al or tantalum ( Ta ) capacitor electrodes without increasing total internal losses. Interestingly, the measured internal quality factors systematically decrease with increasing room-temperature resistivity of the grAl film for all devices, indicating a trade-off between compactness and internal loss. For our lowest resistivity grAl films, we measure quality factors reaching 3.5 × 10 6 for the all-grAl devices and 4.5 × 10 6 for the hybrid grAl/ Ta devices, similar to state-of-the-art quantum circuits. Our loss analysis suggests that the surface-loss factor of grAl is similar to that of pure Al for our lowest resistivity films, while the increasing losses with resistivity could be explained by increasing inductor loss in the grAl film.
Quantum-limited parametric amplifiers have become increasingly interesting and relevant with the progressing field of quantum computing. However, currently it is still challenging to fabricate these complex devices. In this thesis, we developed cross type Josephson junctions (JJs), lumped element LC resonators, lumped element Josephson parametric amplifiers (JPAs) and Josephson traveling wave parametric amplifiers (JTWPAs). We found and resolved several fabrication issues however we suspect that both the JPA and JTWPA suffered from microshorts in the circuits during the cryogenic measurements. Nevertheless, we managed to measure the resonance frequency of the JPA and have noticed the flux focusing effect when we flux tune it. We preformed room temperature measurements on over 300 JJs and calculated the relative standard deviation (RSD) for various JJ sizes. We found the spread of 30 fabricated resonators and a rough estimate of their Q factors. The JTWPAs developed are non-degenerate four wave mixing amplifiers that use the resonant phase matching (RPM) technique to reduce the phase mismatch problem. The transmission through the measured JTWPA showed 50 dB loss probably caused by presumably a short from the transmission line to ground. However, when the JTWPA was driven with a pump we observed 20 dB increase in transmission in some frequency bands.