Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

The Japan Society of Applied Physics

Fabrication of NbTiN/AlNx/NbTiN junctions towards high-temperature operation of Single-flux-quantum circuits

Shunya Sakamoto

Published Feb 6, 2014• 0 citations
OpenAlex

Related papers

Evaluation of temperature-dependent properties of the sheet inductance of NbTiN wires towards high-temperature operation of single-flux-quantum circuits

Shunya Sakamoto

The Japan Society of Applied Physics•Feb 6, 2015•0 citations

Fabrication of high quality Nb/Al/AlOx/Nb stacked Josephson junctions

Paola Barbara, G. Costabile

Physica B Condensed Matter•Feb 1, 1994•3 citations

Fabrication of NbTiN/Al–AlNX/NbTiN Josephson Junctions for Superconducting Circuits Operating Around 10 K

Hiroyuki Akaike, Shunya Sakamoto, Kentaro Munemoto +1 more

We have fabricated NbTiN/Al-AlNX/NbTiN Josephson tunnel junctions on thermally oxidized Si substrates for their applications to single-flux-quantum circuits operating around 10 K. NbTiN films with a critical temperature Tcof 14.2 K and a root-mean-square value of their surface roughness of 0.45 nm were used as junction electrodes. For a junction barrier, radical-nitrided AlNXwas used to realize high uniformity in the critical current Icof the junctions. We obtained NbTiN junctions with a gap voltage Vg of 4.3 mV and an IcRn. product of 2.6 mV at 4.2 K, where R. is the junction resistance. The critical current density Jc, at 4.2 K was obtained in the range between 0.2 and 6.2 kA/cm2by changing a nitridation time for the AlNXbarrier formation. A series array of 200 junctions with an area of 10 μm × 10 μm exhibited a small I', spread, and the standard deviation 1-σ in Icuniformity was less than 1.6% in the temperature range between 4 K and 10 K.

IEEE Transactions on Applied Superconductivity•May 10, 2016•8 citations

Fabrication Process for Nb-based Single Flux Quantum Circuits

Mutsuo Hidaka, Nagasawa Shuichi, K. Hinode +1 more

IEICE Technical Report; IEICE Tech. Rep.•Jan 19, 2007•0 citations

Fabrication and DC-Characterization of NbTiN Based SIS Mixers for Use Between 600 and 1200 GHz

Jeff A. Stern, B. Bumble, Henry George LeDuc +2 more

SIS mixers incorporating two-junction, NbTiN tuning-circuits have been designed and fabricated using two different types of tunnel-junctions. The first type of tunnel junction-NbTiN/MgO/NbTiN--has the advantage of a large gap voltage (5 mV), but has a relatively soft I-V characteristic and high specific capacitance as compared to Nb/Al-Ox/Nb tunnel-junctions. The second type of junction--Nb/Al-AlNx/NbTiN, is a hybrid structure, which has many of the advantages of Nb junctions, with a slightly larger energy gap voltage (3.5 mV) and more robust thermal properties. A detailed description of the deposition techniques used in making the AlNx devices will be given in a separate paper. In this paper, we discuss the deposition of high-quality NbTiN films, and the trade-off between stress and quality in these films. We also discuss the deposition details for the NbTiN/MgO/NbTiN junctions. We measured the magnetic-penetration-depth of our NbTiN films with SQUID circuits. Using long resonators coupled to Josephson junctions, we measured propagation velocities for our microstrip-line circuits; this measurement gave us an independent estimate of the NbTiN magnetic-penetration-depth and a qualitative measure of RF-losses in the microstrip-lines.

Softwaretechnik-Trends•Mar 1, 1998•26 citations

NbN Josephson Junctions for Single-Flux-Quantum Circuits

Hiroyuki Akaike, Naoto Naito, Yuki NAGAI +1 more

We describe the fabrication processes and electrical characteristics of two types of NbN junctions. One is a self-shunted NbN/NbNx/AlN/NbN Josephson junction, which is expected to improve the density of integrated circuits; the other is an underdamped NbN/AlNx/NbN tunnel junction with radical-nitride AlNx barriers, which has highly controllable junction characteristics. In the former, the junction characteristics were changed from underdamped to overdamped by varying the thickness of the NbNx layer. Overdamped junctions with a 6-nm-thick NbNx film exhibited a characteristic voltage of Vc =0.8mV and a critical current density of Jc =22A/cm2 at 4.2K. In the junctions with radical-nitride AlNx barriers, Jc could be controlled in the range 0.01-3kA/cm2 by varying the process conditions, and good uniformity of the junction characteristics was obtained.

IEICE Transactions on Electronics•Jan 1, 2011•0 citations
We have fabricated NbTiN/Al-AlNX/NbTiN Josephson tunnel junctions on thermally oxidized Si substrates for their applications to single-flux-quantum circuits operating around 10 K. NbTiN films with a critical temperature Tcof 14.2 K and a root-mean-square value of their surface roughness of 0.45 nm were used as junction electrodes. For a junction barrier, radical-nitrided AlNXwas used to realize high uniformity in the critical current Icof the junctions. We obtained NbTiN junctions with a gap voltage Vg of 4.3 mV and an IcRn. product of 2.6 mV at 4.2 K, where R. is the junction resistance. The critical current density Jc, at 4.2 K was obtained in the range between 0.2 and 6.2 kA/cm2by changing a nitridation time for the AlNXbarrier formation. A series array of 200 junctions with an area of 10 μm × 10 μm exhibited a small I', spread, and the standard deviation 1-σ in Icuniformity was less than 1.6% in the temperature range between 4 K and 10 K.
SIS mixers incorporating two-junction, NbTiN tuning-circuits have been designed and fabricated using two different types of tunnel-junctions. The first type of tunnel junction-NbTiN/MgO/NbTiN--has the advantage of a large gap voltage (5 mV), but has a relatively soft I-V characteristic and high specific capacitance as compared to Nb/Al-Ox/Nb tunnel-junctions. The second type of junction--Nb/Al-AlNx/NbTiN, is a hybrid structure, which has many of the advantages of Nb junctions, with a slightly larger energy gap voltage (3.5 mV) and more robust thermal properties. A detailed description of the deposition techniques used in making the AlNx devices will be given in a separate paper. In this paper, we discuss the deposition of high-quality NbTiN films, and the trade-off between stress and quality in these films. We also discuss the deposition details for the NbTiN/MgO/NbTiN junctions. We measured the magnetic-penetration-depth of our NbTiN films with SQUID circuits. Using long resonators coupled to Josephson junctions, we measured propagation velocities for our microstrip-line circuits; this measurement gave us an independent estimate of the NbTiN magnetic-penetration-depth and a qualitative measure of RF-losses in the microstrip-lines.
We describe the fabrication processes and electrical characteristics of two types of NbN junctions. One is a self-shunted NbN/NbNx/AlN/NbN Josephson junction, which is expected to improve the density of integrated circuits; the other is an underdamped NbN/AlNx/NbN tunnel junction with radical-nitride AlNx barriers, which has highly controllable junction characteristics. In the former, the junction characteristics were changed from underdamped to overdamped by varying the thickness of the NbNx layer. Overdamped junctions with a 6-nm-thick NbNx film exhibited a characteristic voltage of Vc =0.8mV and a critical current density of Jc =22A/cm2 at 4.2K. In the junctions with radical-nitride AlNx barriers, Jc could be controlled in the range 0.01-3kA/cm2 by varying the process conditions, and good uniformity of the junction characteristics was obtained.