Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

The Japan Society of Applied Physics

Demonstrations of SFQ logic gates by All-NbN integrated circuits (11.5)

Kazumasa Makise

Published Feb 13, 2013• 0 citations
OpenAlex

Related papers

Design and Demonstration of Pipelined Circuits Using SFQ Logic

A. Akahori, Sekiya Akito, Takahiro Yamada +2 more

IEICE Transactions on Electronics•Mar 1, 2002•1 citation

Fabrication and test of 9K NbN SFQ circuits

J.C. Villégier, D. Renaud, C. Bornier +1 more

•Oct 7, 2012•0 citations

NAND Gate for SFQ Logic Circuits

Hiroaki Myoren, Seiichiro Ono, S. Takada

IEICE Transactions on Electronics•Jan 25, 2000•1 citation

Design and Fabrication of All-NbN SFQ Circuits for SSPD Signal Processing

Kazumasa Makise, Hirotaka Terai, Shigehito Miki +2 more

We have developed an all-NbN integrated circuit technology for future integration of single flux quantum (SFQ) circuit with superconducting single-photon detector array. The all-NbN integrated circuits consist of epitaxial NbN/AlN/NbN tunnel junctions fabricated on single-crystal MgO substrates, Mo shunt resistors and 500-nm-thick NbN ground plane on the top. Critical current density and sheet resistance of the Mo resistor were set at 2.5 kA/cm2and 1.2 Ω, respectively. Current uniformity of the NbN/AlN/NbN tunnel junctions was measured to be σ = 3% for 3 μm × 3 μm junction size. The NbN-based SFQ logic cells were designed for and tested at 4.2 K. We actually measured circuit inductances of the fabricated SFQ cells. Circuit simulation revealed that the measured circuit inductances in the fabricated SFQ cells should allow operating margins of more than +/-20%.

IEEE Transactions on Applied Superconductivity•Dec 20, 2012•29 citations

Operation of single-flux-quantum logic cells based on all-NbN integrated circuit technology

Hirotaka Terai, Kazumasa Makise, Zhen Wang

We developed NbN-based SFQ circuits consisting of high-quality epitaxial NbN/AlN/NbN trilayer grown on MgO (100) substrate. The SFQ logic cells such as JTL, DC/SFQ converter, voltage driver, pulse splitter, TFF, and CB were designed by setting the critical current density JCat 2.5 kA/cm2. We succeeded in demonstrating correct operations of all the designed SFQ cells, but the JCrange allowing the operation was quite narrow as around 70% for the designed value. The circuit simulation revealed that the TFF cell requires the JCrange from 65% to 115% for the correct operation, while the DC/SFQ converter was not operational for the JCof more than 70%.

IEEE International Superconductive Electronics Conference (ISEC)•Jul 1, 2013•3 citations

Design of SFQ logic circuits using a Logic Synthesis tool

彩 秋本, 裕希 山梨, 信行 吉川

電子情報通信学会技術研究報告. SCE, 超伝導エレクトロニクス•Oct 15, 2004•0 citations
We have developed an all-NbN integrated circuit technology for future integration of single flux quantum (SFQ) circuit with superconducting single-photon detector array. The all-NbN integrated circuits consist of epitaxial NbN/AlN/NbN tunnel junctions fabricated on single-crystal MgO substrates, Mo shunt resistors and 500-nm-thick NbN ground plane on the top. Critical current density and sheet resistance of the Mo resistor were set at 2.5 kA/cm2and 1.2 Ω, respectively. Current uniformity of the NbN/AlN/NbN tunnel junctions was measured to be σ = 3% for 3 μm × 3 μm junction size. The NbN-based SFQ logic cells were designed for and tested at 4.2 K. We actually measured circuit inductances of the fabricated SFQ cells. Circuit simulation revealed that the measured circuit inductances in the fabricated SFQ cells should allow operating margins of more than +/-20%.
We developed NbN-based SFQ circuits consisting of high-quality epitaxial NbN/AlN/NbN trilayer grown on MgO (100) substrate. The SFQ logic cells such as JTL, DC/SFQ converter, voltage driver, pulse splitter, TFF, and CB were designed by setting the critical current density JCat 2.5 kA/cm2. We succeeded in demonstrating correct operations of all the designed SFQ cells, but the JCrange allowing the operation was quite narrow as around 70% for the designed value. The circuit simulation revealed that the TFF cell requires the JCrange from 65% to 115% for the correct operation, while the DC/SFQ converter was not operational for the JCof more than 70%.