This thesis is an expansion on previous work using the photostop technique for the production of near-zero velocity atoms and molecules. The goal is to produce stopped SH molecules and trap them in a permanent magnetic trap and the aim of this project was to construct a new experimental apparatus to accomplish this. During initial tests of the apparatus, the Rayleigh scattering cross-section of N2 was measured to provide a reference point for future experiments. The uncertainty and systematic errors in the measurements was such that denitive quantitative results of this were not be obtained at this stage. The emerging technique of cavity-enhanced laser-induced uorescence (CELIF) was used to perform absolute number density measurements of a molecular beam of SO2. CELIF was then applied to measuring the photostop of SD/SH. This showed that CELIF would not have the required sensitivity to measure the trapped SD/SH molecules due to issues of stray light from the lasers. As a result of this we elected to use resonance-enhanced multi-photon ionisation (REMPI) as an alternative. We devised and constructed a novel ion extraction system for use in performing REMPI, which was based on a time-of- ight mass spectroscopy system, but utilising the magnets themselves as electrodes, as well as some ion lensing components. This was initially tested using Xe, showing a strong signal and good mass resolution. Using this, the photostop of SH and S was measured showing that the detection apparatus is able to distinguish signal over a range of 9 orders of magnitude. However, despite this sensitivity, the trapping of these stopped molecules could not initially be demonstrated as the signal from these stopped molecules was obscured by signal from the inadvertent dissociation of the background parent molecules by the probe laser. More recent measurements in the group have directly addressed this issue with background subtraction and the results have now demonstrated the trapping of SH. Signicant headway has been made in the demonstration of the trapping of SH produced by photostop. From the results produced using REMPI the detection limit has improved signicantly over the prior experiments and very recent measurements have successfully demonstrated the trapping of SH.
This thesis is an expansion on previous work using the photostop technique for the production of near-zero velocity atoms and molecules. The goal is to produce stopped SH molecules and trap them in a permanent magnetic trap and the aim of this project was to construct a new experimental apparatus to accomplish this. During initial tests of the apparatus, the Rayleigh scattering cross-section of N2 was measured to provide a reference point for future experiments. The uncertainty and systematic errors in the measurements was such that denitive quantitative results of this were not be obtained at this stage. The emerging technique of cavity-enhanced laser-induced uorescence (CELIF) was used to perform absolute number density measurements of a molecular beam of SO2. CELIF was then applied to measuring the photostop of SD/SH. This showed that CELIF would not have the required sensitivity to measure the trapped SD/SH molecules due to issues of stray light from the lasers. As a result of this we elected to use resonance-enhanced multi-photon ionisation (REMPI) as an alternative. We devised and constructed a novel ion extraction system for use in performing REMPI, which was based on a time-of- ight mass spectroscopy system, but utilising the magnets themselves as electrodes, as well as some ion lensing components. This was initially tested using Xe, showing a strong signal and good mass resolution. Using this, the photostop of SH and S was measured showing that the detection apparatus is able to distinguish signal over a range of 9 orders of magnitude. However, despite this sensitivity, the trapping of these stopped molecules could not initially be demonstrated as the signal from these stopped molecules was obscured by signal from the inadvertent dissociation of the background parent molecules by the probe laser. More recent measurements in the group have directly addressed this issue with background subtraction and the results have now demonstrated the trapping of SH. Signicant headway has been made in the demonstration of the trapping of SH produced by photostop. From the results produced using REMPI the detection limit has improved signicantly over the prior experiments and very recent measurements have successfully demonstrated the trapping of SH.
Successful magnetic trapping of both SH at a density of 2.4 x 10^5 cm^-3 and atomic oxygen at a density of 3000 +/- 900 cm^-3 has been demonstrated with respective trapping lifetimes of 40 +/- 10 ms and 82 +/- 3 ms inside a 0.41 T deep, anti-Helmholtz configuration magnetic trap. To achieve trapping of these species, a stable precursor was cooled by supersonic expansion in a molecular beam and photodissociated in such a way as to match and oppose a photofragments recoil speed to the precursors molecular beam speed. This process is called photostop. Velocity-map images have been taken of photostop of atomic oxygen from photodissociation of NO2 in a molecular beam. They show that atomic oxygen can be photostopped from a variety of NO photodissociation co-fragments with a suitably broad molecular-beam velocity-distribution. Although photostop is simple and cheap to use, the trapping lifetimes and densities that have been achieved in this thesis are not competitive compared to other methods of trapping similar molecular species. The main problem that presents universally in photostop experiments is due to the large number of fast molecules from the supersonic expansion that pass through the trap after the photostop event. Only a small fraction of the molecules in the molecular beam are stopped and the remaining ones cause significant trap loss through high energy elastic collisions with trapped species. Work has been carried out to develop the cavity-enhanced laser-induced-fluorescence (CELIF) technique to be used more widely in the cold molecules field. The technique was employed unsuccessfully to measure photostopped SH radicals but was used elsewhere to measure cold SD radicals after Stark deceleration. In addition, the technique has been initially developed for use inside magnetic traps. Clusters of NO.Ar(n) have been studied using [1+1'] REMPI to assess the viability of a new soft-ionisation technique for molecular clusters of atmospheric interest. This work did not show conclusive evidence that [1+1'] REMPI would reduce cluster fragmentation and displayed some interesting but poorly understood data.
This thesis describes the development of a relatively novel technique for the gen- eration and subsequent trapping of cold species. Molecules in a pulsed supersonic expansion are photolysed, such that the centre-of-mass velocity vector of one of the fragments is equal in magnitude but opposed in orientation to the lab-frame velocity of the precursor molecule. This technique, known as ‘Photostop’, leaves a fraction of the fragments with a narrow velocity distribution, centered around zero velocity in the lab-frame. They can be shown to have zero velocity by changing the time between photodissociation and ionisation; fragments with a high kinetic energy will leave the ionisation volume prior to interrogation. The underlying velocity distribu- tion is uncovered by using the velocity-map imaging technique, and the temperature of the fragments can be determined.The method was originally optimised for the molecular case. Cold NO has been produced from the dissociation of NO₂ molecules, and a single rotational state has been shown to remain in the ionisation volume 10 μs after dissociation, implying a sample temperature of 1.17 K. Using the optimised experimental conditions de- rived from the velocity cancellation of NO, the atomic case is demonstrated for the dissociation of Br₂ to give zero-velocity Br fragments. The Br atoms are seen for delay times in excess of 100 μs, showing the greater applicability of the method to the atomic case. The temperature of the residual atoms is shown to be in the milliKelvin regime, as determined through detailed Monte Carlo simulation of the motion of the stopped atoms. The possibility of trapping the ultracold Br atoms in a magnetic field is explored, and a quadrupolar trap created between two per- manent bar magnets is demonstrated to confine the atoms spatially, within the ion extraction optics, for delays in excess of 1 ms.The Photostop technique is intended to be a stepping stone on the way to widening the number of chemical species available for study in the ultracold regime. The possibility of improvements to the experiment is considered, in order to increase the efficiency of the experiment such that the number density becomes high enough to be viable as a source of atoms for use in cold chemical reactive studies. The possibility of extending the method so as to be used as a tunable velocity source of atoms is also discussed.
This thesis demonstrates the feasibility of producing the first cold source of halogen atoms, using Br atoms as the focus. Br atoms are produced by photodissociation of Br2, and detected by (2+1) REMPI and time-of-flight measurements. Ground- and excited-state Br fragments are formed with a recoil velocity directed along the molecular beam axis. The excess energy from the dissociation laser provides the backscattered Br fragments with sufficient recoil velocity to match and cancel out the average velocity of the molecular beam. The Br fragments which undergo sufficient velocity cancellation remain in the laser detection volume for up to 5 ms. A magnetic trap, composed of two permanent bar magnets with their North poles facing each other, is placed around the detection volume and with an axis perpendicular to the molecular beam and laser axes. The centres of the trap and of the laser interaction volume are overlapped. The magnetic field is linear near the centre of the trap and forms a 3-dimensional well with a depth of 0.22 T, equivalent to a trap depth of U0/kB = 255 mK, with the upper and lower standard error [215,325] mK, for ground-state Br. With this configuration, Br atoms have been detected up to delays of 99 ms, to the next laser pulse, suggesting the possibility of accumulating density over successive molecular beam cycles. The decay of Br atoms from the trap is measured, and a Monte Carlo Markov Chain method is implemented to extract the intensity of the Br signal, which decreases to be on the order of the background noise at delays close to 99 ms. Monte-Carlo simulations demonstrate that the trap loss mechanisms are primarily due to collisions with the molecular beam and background gas, inhibiting the ability to accumulate trap density. These simulations also show that Majorana transitions to higher quantum states are minimal and can be ignored. Experimental measurements confirm that near the peak of the molecular beam, when the strongest signal of Br is observed at long delays, around 60% of initially trapped Br atoms are lost due to molecular beam collisions, and (34 ±3)% due to collisions with the background gas. To minimise molecular beam collisions, a chopper construct is designed to reduce the beam pulse width and is placed between the molecular beam valve and detection volume. The chopper runs from 3,000 rpm to 80,000 rpm, during which the duration of the molecular beam at the detection volume is shortened from 130 μs (measured at the full width at half maximum) to between 80 μs and 13 μs, respectively. However, the chopper significantly reduces the initial Br2 density in the trapping region, and the influence of the chopper construct in reducing molecular beam collisions requires further experimental work. Further work is also necessary to improve the operational components, such as reducing the base pressure in the detection chamber to lower background gas collisions, or using a heavier carrier gas to increase density of initially trapped Br atoms. These improvements can lead us closer toward building density of cold Br atoms in the trap over successive molecular beam cycles, with which a source of cold, dense halogen atoms can be realised.
Samples of cold and ultracold polar molecules have the potential to revolutionize physical chemistry, precision measurement, and few-body quantum physics. This thesis describes experimental results for the production of cold samples of OH radicals by Stark deceleration of a supersonic beam. Since Stark deceleration cannot increase the phase space density of the sample, the initial production stage of the OH molecule is critical. The first set of experiments describes a general methodology for the production of OH beams with maximal phase space density, as well as the subsequent coupling to a Stark decelerator. Additionally, we describe the redesign of our electrostatic trap, optimized for future collision experiments of OH with co-trapped ultracold Rb atoms. The new design resulted in a 15-fold increase in total number of trapped molecules over the previous design when tested with ND3 molecules. The second set of experiments focuses on laser-based detection of OH molecules at the exit of the decelerator based on laser induced fluorescence (LIF) and resonance enhanced multiphoton ionizaton (REMPI). The latter method uses vacuum-ultraviolet light at 118nm produced by third-harmonic generation in Xe/Ar gas mixtures as the ionizing step. The sensitivity of this latter technique is limited by the attainable photon flux of the ionizing radiation at 118nm. We present detailed measurements of the conversion efficiencies as well as absolute photon fluxes. Strategies to overcome these limitations as well as prospects for detection of OH molecules in a trap are discussed.
A range of experimental techniques for application in reaction studies between ionic and neutral atoms/molecules and high resolution spectroscopy experiments with sympathetically cooled molecular ions are presented. A novel ion trap loading scheme using the photo-ionisation of atoms generated by the pulsed laser ablation of a solid calcium target has been characterised. We have identified the range of ablation laser fluences that must be used in order to produce a flux of neutral calcium atoms, which is a prerequisite for isotope selective ion trap loading. Calcium ions are trapped and laser cooled in a linear radio-frequency ion trap. We have developed a spectroscopy scheme that allows the entire fluorescence spectrum of trapped ions to be rapidly collected with high precision while maintaining a low ion temperature and good ion localisation throughout interrogation. The scheme has been demonstrated by measuring the saturation intensity of the calcium ion 4S1/2?4P1/2 transition. We have developed a novel scheme to measure the secular motion of trapped ions and demonstrated the application of the technique to ion-neutral collision reaction experiments. Employing pulsed excitation and Doppler velocimetry, we have measured the centre-of-mass mode frequency of single ions as well as large ion crystals with a frequency precision better than 2x10-3 within an interrogation time on the order of seconds. This method has been used to measure the mass of ions and observe charge exchange collisions between trapped calcium isotopes. In particular, we have measured the 44Ca++40Ca!40Ca++44Ca reaction cross section and demonstrated the single-event resolution of the technique. Finally, we have developed a novel all-optical broadband scheme for exciting, amplifying and measuring the secular motion of ions in the trap. Oscillation induced by optical excitation has been coherently amplified to control and measure the ion's secular motion. Requiring only a single interrogation laser, the ion's oscillation amplitude can be precisely controlled. The application of this technique to non-destructive spectroscopy of trapped molecular ions is discussed.
This thesis describes experimental work towards developing a trapped ion quantum information processor. An existing ion trap apparatus was capable of trapping and laser-cooling single ions or small ion strings of 40 Ca+, and had been used for studies of quantum jumps and natural lifetime measurements in Ca. This thesis describes improvements in this apparatus, which have allowed the stability and the flexibility of experimental control of the ions to be greatly increased. This enabled experiments to read out the spin state of a single trapped ion, and to load ions with isotope selectivity through photoionization. The optical systems were improved by installation of new lasers, optical reference cavities, and a system of acousto-optic modulators for laser intensity switching and frequency control. The photon counting for fluorescence detection was improved, and a new photon time-of-arrival correlation circuit developed. This has permitted rapid and more sensitive detection of micromotion, and hence cancellation of stray fields in the trap. A study of resonant circuits in the low RF, high voltage (10 MHz, 1 kV) regime was carried out with a view to developing a new RF supply for the Paul trap with reduced noise and increased power. A new supply based on a helical resonator was built and used to trap ions. This technique has reduced noise and will permit higher secular frequencies to be attained in the future. A magnetic field B in the ion trap is used to define a quantization axis, and in one series of experiments was required to be of order 100 G to provide a substantial Zeeman splitting. A set of magnetic field coils to control the size and direction of B is described. The design of these posed some problems owing to an unforseen issue with the vacuum chamber. In short, it is magnetizable and acts to first approximation like a magnetic shield. The field coils had to be sufficiently substantial to produce the desired field at the ion even in the presence of this shielding effect, and dark resonance (and other) spectra with Zeeman splitting were obtained to calibrate the field using the ion as a probe. Finally, the thesis describes the successful loading of the ion trap by laser photoionization from a weak atomic beam. This involved two new lasers at 423 nm and 389 nm. Saturated absorption spectroscopy of neutral calcium is first described, then transverse excitation of an atomic beam in our vacuum chamber is used to identify all the main isotopes of calcium and confirm their abundances in our source (a heated sample of natural calcium). Finally, photoionization is used to load the trap. This has three advantages over electron-impact ionization. By avoiding an electron gun, we avoid charging of insulating patches and subsequent electric field drift as they discharge; the flux in the atomic beam and hence calcium (and other) deposits on the electrodes can be greatly reduced; and most importantly, the photoionization is isotope selective. Evidence is presented which suggests that even with an non-enriched source, the rare isotope 43 Ca can be loaded with reasonable efficiency. This isotope is advantageous for quantum information experiments for several reasons, but chiefly because its ground state hyperfine structure can act as a stable qubit.