Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Power Reduction of Josephson Random Access Memory Using Stochastic Resonance

Ryosuke Kihara, Yuki Yamanashi, Nobuyuki Yoshikawa

Published Sep 8, 2016• 4 citations
Publisher

Abstract

A superconducting quantum interference device (SQUID) is used as a memory cell in a superconducting Josephson random access memory (RAM) system. In the Josephson RAM, power is mainly consumed by driver circuits, which drive word and bit lines to select the target memory cell. We investigated the power reduction of READ/WRITE operation of the SQUID memory cell by using a stochastic resonance phenomenon. By using a noise-assisted state transition of the SQUID, the driving current required for the READ/WRITE operation of the memory cell can be reduced. We investigated optimum bias and noise conditions where stochastic resonance efficiently occurs on the basis of analog circuit simulation that takes influences of thermal noises into account. According to the simulation results, the power dissipation required for READ/WRITE operation can be reduced by approximately 20% under the optimum bias and noise conditions when the error rate of READ/WRITE operation is 10-10. We designed a 1-bit rf-SQUID memory cell using the AIST 2.5 kA/cm2Nb standard process 2, and tested the cell by applying a white noise from the room-temperature instrument. The probability that a datum is written to the memory cell and read out correctly was measured under various bias and noise conditions. We have experimentally observed stochastic resonance and obtained the error rate of 10-5 when the power dissipation of READ/WRITE operation is reduced to 80% compared to the conventional Josephson RAM.

DOI
10.1109/tasc.2016.2607156

Related papers

Access Time and Power Dissipation of a Model 256-Bit Single Flux Quantum RAM

Thomas Ortlepp, T. Van Duzer

Superconductor electronics offers logic circuits for high-speed data processing and high-performance computing. The main barrier to practical application is the lack of high-speed and low-power memory. It is widely believed that the most reliable and functional bit cell for superconducting memory is the vortex transitional bit cell, which was successfully used by Nagasawa in a 4-kb memory. This paper reviews existing challenges in this type of Josephson memory devices and discusses engineering issues in implementing a model single flux quantum random access memory. We evaluate the contributions that various components of the memory system make to delay and power dissipation. The 256-bit memory provides an experimentally confirmed read access time of 190 ps. As a result, we found that delay and power dissipation are found largely in the address decoder, line drivers, bit-selection scheme, and the data readout circuitry. With these circuits being similar for various magnetic memory devices, our findings provide essential data for a comprehensive assessment of new concepts for bit cells, readout, and write in superconducting memories.

IEEE Transactions on Applied Superconductivity•Apr 22, 2014•23 citations

A capacitively coupled SFQ Josephson memory cell

Hideo Suzuki, S. Hasuo

The design and experimental results for a novel type of Josephson memory cell are presented. The cell has a simpler construction than the conventional Henkels-type, using a one-junction SQUID (superconducting quantum interference device) capacitively coupled to a single junction. Binary data are stored as single flux quanta and are destructively read out by sensing a pulse caused by a vortex-mode transition. Computer simulations suggest that the read operation could be performed with a bias margin for the sense junction of +or-28% and that the rise time of the sense current in a 16-bit memory cell would be as fast as 30 ps, despite having to sense a vortex-mode transition. Results are presented for a memory cell fabricated with Nb-AlO/sub x/-Nb junctions.>

IEEE Transactions on Electron Devices•Jul 1, 1988•10 citations

AC-and DC-powered subnanosecond 1-kbit Josephson cache memory design

Y. Wada, Mutsuo Hidaka, Shuichi Nagasawa +1 more

The address decoders, address line drivers, and sense circuits of the fully decoded memory consist of resistor-coupled Josephson logic circuits to realize fast access. The memory cell is constructed from two three-junction symmetric SQUID (superconducting quantum interface device) gates, and a four-flux-quanta storage loop for enabling bipolar current drive. This memory configuration has intrinsic advantages in regard to magnetic flux trapping in address lines and a gate circuit latch-up problem over a DC-powered memory constructed from inductor coupled gates. Individual control and cell circuits were fabricated, using a lead-alloy process, and their operation was verified. A 570-ps read access time is estimated as the sum measured 280-ps decoding time, and calculated 130-ps address line current rising time, 110-ps sense time, and 50-ps signal propagation time. The 1-kb chip is designed to consume 9 mW without voltage regulators.>

IEEE Journal of Solid-State Circuits•Aug 1, 1988•7 citations

Rapid single flux quantum random access memory

Stanislav V. Polonsky, Alex F. Kirichenko, Vasili K. Semenov +1 more

A new design concept for the Josephson-junction random access memory (RAM) has been developed. In contrast to previous RAMs based on single flux quantization (SFQ), in our system READ and WRITE operations employ ballistic transfer of SFQ pulses along bit lines (either Josephson transmission lines, or passive superconducting microstrip lines, or their combination). The basic memory cells are the single-junction SQUIDs, connected serially by the bit lines and inductively coupled to word lines. READ and WRITE operations are performed by sending SFQ pulses in appropriate directions along bit lines, and DC currents of appropriate polarity into word lines. This approach allows design of very dense memories with n/spl les/2 Josephson junctions per bit, memory cell area smaller than 80 /spl lambda//sup 2/ (where /spl lambda/ is the minimum feature size), and the critical parameter margin well above /spl plusmn/20%. In this paper we present the general structure of the RSFQ RAM, as well as design and results of testing of the basic memory cell and decoder circuitry using Hypres' 3.5-/spl mu/m, 1-kA/cm/sup 2/ Nb-trilayer technology.>

IEEE Transactions on Applied Superconductivity•Jun 1, 1995•46 citations

Influence of the Josephson junction on the impedance and noise of a resistive superconductive quantum interference device

Robert J. Soulen, William E. Fogle, Jack H. Colwell +2 more

The impedance and noise of a resistive superconductive quantum interference device (R-SQUID) have been measured as a function of the dc and rf currents applied to it. The Josephson junction was adjustable so that data were also taken for several values of the junction critical current. The results were compared with the predictions of a resistively shunted junction (RSJ) model which takes into account the influence of the Josephson junction on the impedance and noise. The agreement was found to be quite good and demonstrates that the noise in the circuit is well understood. Use of the R-SQUID as a noise thermometer below 1 K is assessed in terms of corrections due to the RSJ model. It is demonstrated how the dc and rf currents may be adjusted so that the total noise of the R-SQUID is reduced to within 0.1% of the Johnson noise generated by the resistor alone. Under these conditions, the R-SQUID may be used as a noise thermometer to determine thermodynamic temperature to this inaccuracy from 6 to 700 mK.

Journal of Applied Physics•Oct 15, 1993•4 citations

Investigation and reduction of excess low-frequency noise in rf superconducting quantum interference devices

Michael Mück, Christoph Heiden, John L. Clarke

A detailed study has been made of the low-frequency excess noise of rf superconducting quantum interference devices (SQUIDs), fabricated from thin niobium films and operated at 4.2 K, with rf bias frequencies of 0.15, 1.7, and 3 GHz. When the SQUIDs were operated in an open-loop configuration in the absence of low-frequency flux modulation, the demodulated rf voltage exhibited a substantial level 1/f noise, which was essentially independent of the rf bias frequency. As the rf bias frequency was increased, the crossover frequency at which the 1/f noise power was equal to the white noise power moved to higher frequencies, because of the reduction in white noise. On the other hand, when the SQUID was flux modulated at 50 kHz and operated in a flux locked loop, no 1/f noise was observed at frequencies above 0.5 Hz. A detailed description of how the combination of rf bias and flux modulation removes 1/f noise due to critical current fluctuations is given. Thus, the results demonstrate that the 1/f noise observed in these SQUIDs is generated by critical current fluctuations, rather than by the hopping of flux vortices in the niobium films.

Journal of Applied Physics•May 1, 1994•26 citations
A superconducting quantum interference device (SQUID) is used as a memory cell in a superconducting Josephson random access memory (RAM) system. In the Josephson RAM, power is mainly consumed by driver circuits, which drive word and bit lines to select the target memory cell. We investigated the power reduction of READ/WRITE operation of the SQUID memory cell by using a stochastic resonance phenomenon. By using a noise-assisted state transition of the SQUID, the driving current required for the READ/WRITE operation of the memory cell can be reduced. We investigated optimum bias and noise conditions where stochastic resonance efficiently occurs on the basis of analog circuit simulation that takes influences of thermal noises into account. According to the simulation results, the power dissipation required for READ/WRITE operation can be reduced by approximately 20% under the optimum bias and noise conditions when the error rate of READ/WRITE operation is 10-10. We designed a 1-bit rf-SQUID memory cell using the AIST 2.5 kA/cm2Nb standard process 2, and tested the cell by applying a white noise from the room-temperature instrument. The probability that a datum is written to the memory cell and read out correctly was measured under various bias and noise conditions. We have experimentally observed stochastic resonance and obtained the error rate of 10-5 when the power dissipation of READ/WRITE operation is reduced to 80% compared to the conventional Josephson RAM.
Superconductor electronics offers logic circuits for high-speed data processing and high-performance computing. The main barrier to practical application is the lack of high-speed and low-power memory. It is widely believed that the most reliable and functional bit cell for superconducting memory is the vortex transitional bit cell, which was successfully used by Nagasawa in a 4-kb memory. This paper reviews existing challenges in this type of Josephson memory devices and discusses engineering issues in implementing a model single flux quantum random access memory. We evaluate the contributions that various components of the memory system make to delay and power dissipation. The 256-bit memory provides an experimentally confirmed read access time of 190 ps. As a result, we found that delay and power dissipation are found largely in the address decoder, line drivers, bit-selection scheme, and the data readout circuitry. With these circuits being similar for various magnetic memory devices, our findings provide essential data for a comprehensive assessment of new concepts for bit cells, readout, and write in superconducting memories.
The design and experimental results for a novel type of Josephson memory cell are presented. The cell has a simpler construction than the conventional Henkels-type, using a one-junction SQUID (superconducting quantum interference device) capacitively coupled to a single junction. Binary data are stored as single flux quanta and are destructively read out by sensing a pulse caused by a vortex-mode transition. Computer simulations suggest that the read operation could be performed with a bias margin for the sense junction of +or-28% and that the rise time of the sense current in a 16-bit memory cell would be as fast as 30 ps, despite having to sense a vortex-mode transition. Results are presented for a memory cell fabricated with Nb-AlO/sub x/-Nb junctions.>
The address decoders, address line drivers, and sense circuits of the fully decoded memory consist of resistor-coupled Josephson logic circuits to realize fast access. The memory cell is constructed from two three-junction symmetric SQUID (superconducting quantum interface device) gates, and a four-flux-quanta storage loop for enabling bipolar current drive. This memory configuration has intrinsic advantages in regard to magnetic flux trapping in address lines and a gate circuit latch-up problem over a DC-powered memory constructed from inductor coupled gates. Individual control and cell circuits were fabricated, using a lead-alloy process, and their operation was verified. A 570-ps read access time is estimated as the sum measured 280-ps decoding time, and calculated 130-ps address line current rising time, 110-ps sense time, and 50-ps signal propagation time. The 1-kb chip is designed to consume 9 mW without voltage regulators.>
A new design concept for the Josephson-junction random access memory (RAM) has been developed. In contrast to previous RAMs based on single flux quantization (SFQ), in our system READ and WRITE operations employ ballistic transfer of SFQ pulses along bit lines (either Josephson transmission lines, or passive superconducting microstrip lines, or their combination). The basic memory cells are the single-junction SQUIDs, connected serially by the bit lines and inductively coupled to word lines. READ and WRITE operations are performed by sending SFQ pulses in appropriate directions along bit lines, and DC currents of appropriate polarity into word lines. This approach allows design of very dense memories with n/spl les/2 Josephson junctions per bit, memory cell area smaller than 80 /spl lambda//sup 2/ (where /spl lambda/ is the minimum feature size), and the critical parameter margin well above /spl plusmn/20%. In this paper we present the general structure of the RSFQ RAM, as well as design and results of testing of the basic memory cell and decoder circuitry using Hypres' 3.5-/spl mu/m, 1-kA/cm/sup 2/ Nb-trilayer technology.>
The impedance and noise of a resistive superconductive quantum interference device (R-SQUID) have been measured as a function of the dc and rf currents applied to it. The Josephson junction was adjustable so that data were also taken for several values of the junction critical current. The results were compared with the predictions of a resistively shunted junction (RSJ) model which takes into account the influence of the Josephson junction on the impedance and noise. The agreement was found to be quite good and demonstrates that the noise in the circuit is well understood. Use of the R-SQUID as a noise thermometer below 1 K is assessed in terms of corrections due to the RSJ model. It is demonstrated how the dc and rf currents may be adjusted so that the total noise of the R-SQUID is reduced to within 0.1% of the Johnson noise generated by the resistor alone. Under these conditions, the R-SQUID may be used as a noise thermometer to determine thermodynamic temperature to this inaccuracy from 6 to 700 mK.
A detailed study has been made of the low-frequency excess noise of rf superconducting quantum interference devices (SQUIDs), fabricated from thin niobium films and operated at 4.2 K, with rf bias frequencies of 0.15, 1.7, and 3 GHz. When the SQUIDs were operated in an open-loop configuration in the absence of low-frequency flux modulation, the demodulated rf voltage exhibited a substantial level 1/f noise, which was essentially independent of the rf bias frequency. As the rf bias frequency was increased, the crossover frequency at which the 1/f noise power was equal to the white noise power moved to higher frequencies, because of the reduction in white noise. On the other hand, when the SQUID was flux modulated at 50 kHz and operated in a flux locked loop, no 1/f noise was observed at frequencies above 0.5 Hz. A detailed description of how the combination of rf bias and flux modulation removes 1/f noise due to critical current fluctuations is given. Thus, the results demonstrate that the 1/f noise observed in these SQUIDs is generated by critical current fluctuations, rather than by the hopping of flux vortices in the niobium films.