Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Bulletin of the American Physical Society

Sub-picotesla Scalar Atomic Magnetometer with a Microfabricated Vapor Cell

Rui Zhang, Rahul R. Mhaskar

Published May 27, 2016• 0 citations
OpenAlex

Related papers

Free-Induction-Decay Magnetometer Based on a Microfabricated Cs Vapor Cell

Dominic Hunter, S. Piccolomo, Jonathan D. Pritchard +3 more

Microfabricated atomic magnetometers are important for fundamental research and numerous applications, including geophysical surveying and biological imaging, as they provide a sensitive, accurate, and portable alternative to standard magnetic sensing. The strong scalability and all-optical nature of the free-induction-decay (FID) magnetometer also benefit applications requiring sensor networks. This study shows the advantages of applying synchronous modulation and differential polarimetric detection in an FID setting, for measuring picotesla-level fields using a miniaturized Cs vapor cell.

Physical Review Applied•Jul 5, 2018•70 citations

Subpicotesla atomic magnetometry with a microfabricated vapour cell

Vishal Shah, Svenja A. Knappe, Peter D. D. Schwindt +1 more

Nature Photonics•Nov 1, 2007•433 citations

Subpicotesla scalar atomic magnetometer with a microfabricated cell

Rui Zhang, Terry Dyer, Nathan Brockie +2 more

We demonstrated a scalar atomic magnetometer using a microfabricated Cs vapor cell. The atomic spin precession is driven by an amplitude-modulated circularly-polarized pump laser resonant on the D1 transition of Cs atoms and detected by an off-resonant linearly-polarized probe laser using a balanced polarimeter setup. Under a magnetic field with amplitude in the Earth's magnetic field range, the magnetometer in the gradiometer mode can reach sensitivities below 150fT/Hz, which shows that the magnetometer by itself can achieve sub-100fT/Hz sensitivities. In addition to its high sensitivity, the magnetometer has a bandwidth close to 1 kHz due to the broad magnetic resonance inside the small vapor cell. Our experiment suggests the feasibility of a portable low-power and high-performance magnetometer which can be operated in the Earth's magnetic field. Such a device will greatly reduce the restrictions on the operating environment and expand the range of applications for atomic magnetometers, such as detection of nuclear magnetic resonance in low magnetic fields.

arXiv:1910.01768•Journal of Applied Physics•Sep 26, 2019•17 citations

A Microfabricated Tunable Cavity Atomic Magnetometer.

Peter D. D. Schwindt, Murat Okandan, Cort Johnson

•Mar 1, 2009•0 citations

Microfabricated multi-axis cell for integrated atomic devices

Linda Péroux, A. Dewilde, Andrei Mursa +12 more

Abstract Microfabricated alkali vapor cells enable the miniaturization of atomic sensors, but require collective wafer-level integration of complex features. In many applications-including magnetometers, gyroscopes, magneto-optical traps, and fluorescence imaging-multiple optical accesses are needed to enhance performance. Yet, achieving this without compromising manufacturability remains challenging. In this work, we present a wafer-level fabrication approach that enables three orthogonal optical pathways in microfabricated alkali vapor cells, using fully scalable and collective processes. Our method relies on the thermal reflow of glass preforms, shaped by laser-assisted etching (LAE) and bonded between silicon frames. The relatively low surface roughness produced by LAE allows for effective reflow, which further smooths the surfaces without significantly compromising the optical planarity of the windows. This process results in multi-axis vapor cells featuring embedded, optics-grade lateral windows. We evaluate the device performance through both single-beam and dual-beam atomic magnetometry measurements. Magnetic sensitivities better than 200 fT Hz − 1 are demonstrated along each of the three orthogonal axes, confirming the potential of the approach for tri-axis magnetic field sensing at sub-picotesla resolution. This fabrication strategy opens new perspectives for versatile, high-performance atomic sensors, fully compatible with wafer-level integration and mass production.

arXiv:2509.22456•Journal of Physics Photonics•Dec 2, 2025•1 citation

Compact Mz atomic magnetometer with a thick silicon core MEMS vapor cell

Qi Li, Jianan Qin, Yuejin Jiang +2 more

Optics Communications•Jul 14, 2024•5 citations
Microfabricated atomic magnetometers are important for fundamental research and numerous applications, including geophysical surveying and biological imaging, as they provide a sensitive, accurate, and portable alternative to standard magnetic sensing. The strong scalability and all-optical nature of the free-induction-decay (FID) magnetometer also benefit applications requiring sensor networks. This study shows the advantages of applying synchronous modulation and differential polarimetric detection in an FID setting, for measuring picotesla-level fields using a miniaturized Cs vapor cell.
We demonstrated a scalar atomic magnetometer using a microfabricated Cs vapor cell. The atomic spin precession is driven by an amplitude-modulated circularly-polarized pump laser resonant on the D1 transition of Cs atoms and detected by an off-resonant linearly-polarized probe laser using a balanced polarimeter setup. Under a magnetic field with amplitude in the Earth's magnetic field range, the magnetometer in the gradiometer mode can reach sensitivities below 150fT/Hz, which shows that the magnetometer by itself can achieve sub-100fT/Hz sensitivities. In addition to its high sensitivity, the magnetometer has a bandwidth close to 1 kHz due to the broad magnetic resonance inside the small vapor cell. Our experiment suggests the feasibility of a portable low-power and high-performance magnetometer which can be operated in the Earth's magnetic field. Such a device will greatly reduce the restrictions on the operating environment and expand the range of applications for atomic magnetometers, such as detection of nuclear magnetic resonance in low magnetic fields.
Abstract Microfabricated alkali vapor cells enable the miniaturization of atomic sensors, but require collective wafer-level integration of complex features. In many applications-including magnetometers, gyroscopes, magneto-optical traps, and fluorescence imaging-multiple optical accesses are needed to enhance performance. Yet, achieving this without compromising manufacturability remains challenging. In this work, we present a wafer-level fabrication approach that enables three orthogonal optical pathways in microfabricated alkali vapor cells, using fully scalable and collective processes. Our method relies on the thermal reflow of glass preforms, shaped by laser-assisted etching (LAE) and bonded between silicon frames. The relatively low surface roughness produced by LAE allows for effective reflow, which further smooths the surfaces without significantly compromising the optical planarity of the windows. This process results in multi-axis vapor cells featuring embedded, optics-grade lateral windows. We evaluate the device performance through both single-beam and dual-beam atomic magnetometry measurements. Magnetic sensitivities better than 200 fT Hz − 1 are demonstrated along each of the three orthogonal axes, confirming the potential of the approach for tri-axis magnetic field sensing at sub-picotesla resolution. This fabrication strategy opens new perspectives for versatile, high-performance atomic sensors, fully compatible with wafer-level integration and mass production.