Monolithic three-dimensional (3D) Paul traps combine the high-precision microfabrication of two-dimensional (2D) chip traps with the deep trapping potentials and low heating rates characteristic of macroscopic 3D Paul traps, which are typically machined by traditional means and mechanically assembled. However, achieving low motional heating rates and optical access with a high numerical aperture (NA) while maintaining the high radio-frequency (RF) voltages required for trapping heavy ionic species, such as Yb
+ and Ba
+, remains a significant technical challenge. In this work, we present a fused-silica, monolithic segmented 3D Paul trap with an ion-electrode distance of 250
μm, and stable operation at high RF voltages. We benchmark the performance of the trap using Yb
+ ions, demonstrating axially homogeneous trapping potentials spanning over 200
μm about the axial center of the trap, high multi-directional optical access (up to 0.7 NA), and radial motional heating as low as $\dot{\bar n}=1.1 \pm 0.1 $ quanta/s at radial trap frequencies about 3 MHz near room temperature. Furthermore, we observe a motional Ramsey coherence time,
T2, of about 95 ms for the radial center-of-mass mode. We demonstrate the generation of a two-qubit Bell state with a parity contrast of
99.3−1.5+0.7% with state preparation and measurement correction. These results establish fused-silica monolithic 3D Paul traps as a scalable, modular platform for quantum simulation, computation, metrology, and networking with heavy ionic species.
The objective of this research is to design, fabricate, and demonstrate a microfabricated \nmonolithic ion trap for applications in quantum computation and quantum simulation. \nMost current microfabricated ion trap designs are based on planar-segmented surface electrodes. \nAlthough promising scalability to trap arrays containing ten to one hundred ions, \nthese planar designs suffer from the challenges of shallow trap depths, radial asymmetry of \nthe confining potential, and electrode charging resulting from laser interactions with dielectric \nsurfaces. In this research, the design, fabrication, and testing of a monolithic \nand symmetric two-level ion trap is presented. This ion trap overcomes the challenges of \nsurface-electrode ion traps. Numerical electrostatic simulations show that this symmetric \ntrap produces a deep (1 eV for 171Yb+ ion), radially symmetric RF confinement potential. \nThe trap has an angled through-chip slot that allows back-side ion loading and generous \nthrough laser access, while avoiding surface-light scattering and dielectric charging that \ncan corrupt the design control electrode compensating potentials. The geometry of the trap \nand its dimensions are optimized for trapping long and linear ion chains with equal spacing \nfor use with quantum simulation problems and quantum computation architectures.
Trapped ions in linear Paul traps are largely isolated from interaction with the environment. This property of trapped ions make them a primary choice for quantum technology. \nOver the last decade, trapped atomic ions in linear radio frequency Paul traps have shown to be an important tool to implement quantum algorithms. The scalability of linear ion \ntraps is required to handle large numbers of qubits, in order to implement useful quantum computation. Advance micro-fabrication technology allows the realisation of scalable ion traps. Further developments of micro-trap designs, for the purpose of scalable quantum technology, requires inter-disciplinary investigations of ion traps. Micro-scale ion trap designs typically require a versatile experimental setup. The first part of this thesis describes such an experimental setup including a chip bracket that can host macroscopic ion traps as well as advanced symmetric and asymmetric ion trap chips with up to 90 control electrodes. The system provides versatile optical access for both type of traps and the vacuum chamber is designed in a way so the ion traps can be replaced within a short amount of time. To test the working of the setup, a macroscopic ion trap with an ion-electrode distance of 310±10 μm is used to trap ytterbium ions (Yb+). The trap is characterised by measuring the heating rate, (n•), and spectral noise density SE(ω). A \nphotoionisation technique is used to ionise the different isotopes of Yb in our trap. Isotope selective photoionisation requires exact measurements of 1So↔1P1 transition for the different Yb isotopes. A technique to measure these resonant frequencies is described. \nThis technique works by observing and aligning fluorescence spots and by using this technique, the 1So↔1P1 transition frequencies for stable isotopes of Yb were measured with an accuracy of 60 MHz. These new measured transition frequencies for stable Yb isotopes differ from previously published work by 660 MHz. Furthermore, this technique can also be used to obtain the transition frequencies at different laser-atomic beam angles, typical for non-perpendicular laser-atomic beam angles. The second part of this thesis discusses the optimisation of surface trap geometries as they are being used to implement scalable ion trap designs which consist of a large number of trapping zones. The trap depth in surface traps is low compared to symmetric traps of similar dimensions. How to optimise the trap geometry to achieve maximum trap depth for a given ion height above the trap electrodes, is discussed. Fast and adiabatic ion shuttling operations in one dimension as well as ion separation and recombination processes are important for many quantum information implementations. The maximum speed of separation of trapped ions for adiabatic shuttling operations depends on the secular frequencies, the trapped ion experiences in the process. It will be shown how such ion trap structures have to be designed for fast ion separation process and linear shuttling. Numerical results of adiabatic shuttling operations for trapped ions in such trap structures are also presented.
Ions trapped in Paul traps provide a system which has been shown to exhibit most of the properties required to implement quantum information processing. In particular, a two-dimensional array of ions has been shown to be a candidate for the implementation of quantum simulations. Microfabricated surface geometries provide a widely used technology with which to create structures capable of trapping the required two-dimensional array of ions. To provide a system which can utilise the properties of trapped ions a greater understanding of the surface geometries which can trap ions in two-dimensional arrays would be advantageous, and allow quantum simulators to be fabricated and tested. In this thesis I will present the design, set-up and implementation of an experimental apparatus which can be used to trap ions in a variety of different traps. Particular focus will be put on the ability to apply radio-frequency voltages to these traps via helical resonators with high quality factors. A detailed design guide will be presented for the construction and operation of such a device at a desired resonant frequency whilst maximising the quality factor for a set of experimental constraints. Devices of this nature will provide greater filtering of noise on the rf voltages used to create the electric field which traps the ions which could lead to reduced heating in trapped ions. The ability to apply higher voltages with these devices could also provide deeper traps, longer ion lifetimes and more efficient cooling of trapped ions. In order to efficiently cool trapped ions certain transitions must be known to a required accuracy. In this thesis the 2S1/2 ? 2P1/2 Doppler cooling and 2D3/2 ? 2D[3/2]1/2 repumping transition wavelengths are presented with a greater accuracy then previous work. These transitions are given for the 170, 171, 172, 174 and 176 isotopes of Yb+. Two-dimensional arrays of ions trapped above a microfabricated surface geometry provide a technology which could enable quantum simulations to be performed allowing solutions to problems currently unobtainable with classical simulation. However, the spin-spin interactions used in the simulations between neighbouring ions are required to occur on a faster time-scale than any decoherence in the system. The time-scales of both the ion-ion interactions and decoherence are determined by the properties of the electric field formed by the surface geometry. This thesis will show how geometry variables can be used to optimise the ratio between the decoherence time and the interaction time whilst simultaneously maximising the homogeneity of the array properties. In particular, it will be shown how the edges of the geometry can be varied to provide the maximum homogeneity in the array and how the radii and separation of polygons comprising the surface geometry vary as a function of array size for optimised arrays. Estimates of the power dissipation in these geometries will be given based on a simple microfabrication.
We describe a novel monolithic ion trap that combines the flexibility and scalability of silicon microfabrication technologies with the superior trapping characteristics of traditional four-rod Paul traps. The performace of the proposed microfabricated trap approaches that of the macroscopic structures. The fabrication process creates an angled through-chip slot which allows backside ion loading and through-laser access while avoiding surface light scattering and dielectric charging. The trap geometry and dimensions are optimized for confining long ion chains with equal ion spacing [G.-D. Lin, et al., Europhys. Lett. 86, 60004 (2009)]. Control potentials have been derived to produce linear, equally spaced ion chains of up to 50 ions spaced at 10 um. With the deep trapping depths achievable in this design, we expect that these chains will be sufficiently long-lived to be used in quantum simulations of magnetic systems [E.E. Edwards, et al., Phys. Rev. B 82, 060412(R) (2010)]. The trap is currently being fabricated at Georgia Tech using VLSI techniques.
In this thesis, the next generation of the ion trapping setup has been designed, constructed, and successfully implemented for studying quantum information science at the University of Bonn. The new setup is designed to include an optical cavity as the endcap electrodes of a linear radio-frequency ion trap. In view of this, a novel method to drive the linear ion trap is invented to apply two-phase radio-frequency voltage. In addition to this, a new method to directly bias all the electrodes of the ion trap with DC voltages is implemented in order to control the static electric fields along all directions. Using these methods, over 6 ytterbium ions in a linear Coulomb crystal can been trapped, and radial trapping frequencies of over 1.2 MHz have been observed using the aforementioned methods. Low axial-micromotion for over 65 µm along the axis of the ion trap has been observed, although the endcap electrodes are just as close to the trapped ions as the linear electrodes. In view of finding a novel approach for photonic interfacing the Yb ions, the lower-lying energy levels involving inner-shell electron excitations are investigated in this thesis. By considering their properties, the 2D3/2 → 4f13 (2Fo5/2)5d6s(3D) 3[5/2]o3/2 transition is successfully interrogated using direct laser excitation for the first time to the best of my knowledge. The transition frequency is measured to be 603013350 ± 162 MHz for the isotope 174Yb. In addition to the study of quantum information science, the new ion trap -- optical cavity setup is also considered for the experimental investigation of microscopic thermodynamics. In view of this, the Hamiltonian of the complete system is derived and compared with the theoretical models of Hamiltonian engines. Various non-linear terms occurring in the system Hamiltonian are described for studying the concept of ignition in a future single ion engine in our linear ion trap.