The flux qubit is often considered as a major design for the future of quantum integrated circuits and its properties have triggered intense interest in the last decade [1-2]. This superconducting circuit behaves as a two-level system, each level being characterized by the direction of a macroscopic permanent current flowing in the loop of the qubit. The permanent current, typically of the order of several hundreds of nAs, generates a large magnetic dipole, which offers interesting prospects for hybrid quantum circuits [3]. However, the flux qubit suffers from limited and irreproducible lifetimes which partially prevent these potential applications. Recently, a novel architecture where qubits are placed in a three dimensional cavity was introduced for transmon qubit [4]. It was shown that coherence properties can be greatly improved.
Abstract Superconducting quantum circuits are a leading platform for quantum-information processing, but their development requires expertise spanning device design, microfabrication, cryogenic operation, microwave control, and quantum characterization. In this work, we report the realization of a flux-tunable superconducting transmon platform and present an integrated workflow encompassing design, fabrication, measurement, and numerical modeling. The device consists of an
Al/AlOx/Al transmon coupled to a three-dimensional microwave cavity operating in the circuit quantum electrodynamics (cQED) dispersive regime. Two-tone spectroscopy reveals a fundamental transition frequency of
ω01=5.0122 GHz and an anharmonicity of
α/2π=−202.4 MHz , corresponding to
EJ/EC≈82.9 . Flux spectroscopy yields a cavity-qubit coupling strength of
g/2π=260 MHz , while the cavity linewidth gives a loaded quality factor of
QL=6127 and a Purcell limit of
T1Purcell≈82 μs . Time-domain measurements yield coherence times of
T1=17.4 μs and
T2∗=5.8 μs . To investigate coherence and dissipation in the device, the experimental observations are analyzed within a Lindblad master-equation framework describing cavity photon loss and thermal excitation, qubit energy relaxation, and pure dephasing processes. Using a set of experimentally extracted parameters, the model reproduces the measured spectroscopic and time-domain observables, providing a quantitative description of the open-system dynamics of the transmon-cavity platform. The analysis shows that the measured coherence is primarily limited by pure dephasing and energy-relaxation processes, whereas thermal excitation plays a minor role under the experimental conditions. Inspired by the broader framework of quantum dissipation in macroscopic quantum systems pioneered by Caldeira and collaborators, this approach enables a quantitative analysis of relaxation and dephasing processes in superconducting quantum circuits. Beyond the characterization of a single device, the present work demonstrates the establishment of the expertise, infrastructure, and experimental workflow required for the design, fabrication, measurement, and modeling of superconducting quantum circuits, contributing to the development of quantum technologies in Brazil and related applications.
This thesis presents circuit quantum electrodynamic (cQED) experiments done with artificial atoms coupled to a high quality factor superconducting microwave resonator. This work discusses the theoretical framework, design, fabrication, implementation and characterization of a multi-qubit system using superconducting persistent current qubits, often referred as flux qubits. \n \nWe developed a new type of cryogenic aid for fast turnaround microwave experiments. The minimum turnaround time to perform microwave experiments in dilution refrigerators is typically a few days, as required by cooling down and warming up the entire refrigerator. The cryogenic microwave payload and wiring needed for each qubit and resonator add a significant heat load to \nthe system which typically only has a few µW s of cooling power at millikelvin temperatures. We present a new experimental approach we developed in which a suitable sample holder is attached to a cold-insertable probe and brought in contact with transmission lines permanently mounted inside the cryostat. The total turnaround time is reduced to 8 hours if the target temperature is 80 mK. This new measurement method increased our ability to successfully identify good devices with fast design-characterization iterations, while allowing months-long measurements at 30 mK. \n \nOur device architecture uses several qubits, each of which is controlled via on-chip fast flux bias lines. Readout of the qubit’s quantum state is performed by homodyne detection of the resonator field at large driving power. We observe long coherence times at the optimal bias point of the flux qubits and present decoherence measurements around this optimal point, where the \nflux qubits couple mostly to magnetic flux noise. Dynamical decoupling techniques employing fast microwave pulses are used to protect the qubit’s coherence and allow calculating the magnetic flux noise power spectral density of the qubit’s environment. Photon-mediated interaction between distant qubits in the resonator allows the implementation of a two-qubit controlled-NOT gate \nusing the selective darkening technique. \n \nThis multi-qubit superconducting design is an interesting platform to study the decoherence properties of flux qubits, the properties of strong interaction of electromagnetic radiation with macroscopic quantum systems. These results demonstrate the potential of cQED as a platform for fundamental investigations of decoherence and quantum dynamics of flux qubits.
A qubit was designed that can be fabricated with conventional electron beam lithography and is suited for integration into a large quantum computer. The qubit consists of a micrometer-sized loop with three or four Josephson junctions; the two qubit states have persistent currents of opposite direction. Quantum superpositions of these states are obtained by pulsed microwave modulation of the enclosed magnetic flux by currents in control lines. A superconducting flux transporter allows for controlled transfer between qubits of the flux that is generated by the persistent currents, leading to entanglement of qubit information.
A qubit was designed that can be fabricated with conventional electron beam lithography and is suited for integration into a large quantum computer. The qubit consists of a micrometer-sized loop with three or four Josephson junctions; the two qubit states have persistent currents of opposite direction. Quantum superpositions of these states are obtained by pulsed microwave modulation of the enclosed magnetic flux by currents in control lines. A superconducting flux transporter allows for controlled transfer between qubits of the flux that is generated by the persistent currents, leading to entanglement of qubit information.
This article reviews a recent experiment that demonstrated a new hybrid type of tunable superconducting qubit consisting of a two-dimensional (2D) superconducting capacitively shunted flux qubit coupled to a 3D microwave cavity.Such a 3D hybrid flux qubit has extremely long relaxation times, which are comparable to or exceed the best values reported for 2D flux qubits.This new design of frequency-tunable qubits is uniquely suited for applications in bosonic quantum computing, which exploits multiphoton states of 3D microwave cavities.