Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Magnetic flux measurement of superconducting qubits with Josephson inductors

Janice C. Lee

Published Jan 1, 2002• 1 citation
OpenAlex

Abstract

Recent research in quantum computation with superconducting qubits relies on SQUID magnetometers to distinguish the supercurrent states of the qubits.This poses a new challenge of demanding the measurement SQUID to introduce the least decoherence on the qubits during the measurement process.The SQUID is desired to operate in an unconventional way and be biased at currents significantly below the critical current level.This thesis lays the fundamental work of achieving the above by using the SQUID as a flux-sensitive inductor.The read-out relies on incorporating the SQUID inductor in a resonant circuit, and the state of the qubit is detected from the resonant frequency of the peak.A series of prototype resonant circuits were made from printed circuit boards and tested at room temperature.On-chip high-Q resonant circuits were designed to optimize the signals in the inductance measurements to about ten microvolts.Calculations of the decoherence times based on the spin-boson model were performed and the relaxation time falls in the microsecond regime.

Related papers

Resonant Readout of a Persistent Current Qubit

J.C. Lee, William D. Oliver, Terry P. Orlando +1 more

We have implemented a resonant circuit that uses a SQUID as a flux-sensitive Josephson inductor for qubit readout. In contrast to the conventional switching current measurement that generates undesired quasiparticles when the SQUID switches to the voltage state, our approach keeps the readout SQUID biased along the supercurrent branch during the measurement. By incorporating the SQUID inductor in a high-Q resonant circuit, we can distinguish the two flux states of a niobium persistent-current (PC) qubit by observing a shift in the resonant frequency of both the magnitude and the phase spectra. The readout circuit was also characterized in the nonlinear regime to investigate its potential use as a nonlinear amplifier.

arXiv:cond-mat/0501283•IEEE Transactions on Applied Superconductivity•Jun 1, 2005•14 citations

Resonant readout of a superconducting persistent current qubit

Janice C. Lee

Superconducting Josephson junction devices rank among the best candidates for realizing a quantum computer. While the coherent control of quantum dynamics has been demonstrated in these solid-state, macroscopic quantum systems, a major challenge has been to increase the coherence times for these qubits. With an objective to reduce the level of readout-induced decoherence, this thesis work focuses on a resonant readout scheme developed for a niobium persistent-current (PC) qubit. This non-dissipative readout approach detects the flux state of the qubit by sensing a change in the Josephson inductance of a SQUID magnetometer. By incorporating the SQUID inductor in a high-Q resonant circuit, we distinguished the flux states of the qubit as a shift in the resonant frequency at 300 mK. The nonlinearity due to the Josephson inductance has characteristic effects on the resonant behavior of the readout circuit. We observed novel manifestation of this nonlinearity given the high quality factor of the resonance. The readout circuit was characterized in the linear as well as the nonlinear regime for its potential use as a bifurcation amplifier. Numerical simulations based on Josephson-junction circuits were also performed to understand the observed nonlinearity in the resonant behavior.

•Jan 1, 2006•0 citations

Measurement of the Energy Relaxation Time in rf SQUID Flux Qubits

Wei Qiu

It is well known that that superconducting qubits based on Josephson junctions have the advantages of scalability and the qubit states are easy to prepare and control. In addition, demonstration of Rabi oscillations in various superconducting circuits shows that superconducting qubits are promising for scalable quantum information processing. However, despite flexibility of design and fabrication, easier to scale up, and fast gate speed, superconducting qubits usually have much shorter decoherence time than trapped ions, NMR etc. due to the relatively strong interactions between qubits and environment. Recent experiments show that low frequency flux noise is the dominant mechanism of decoherence in superconducting flux qubits. However, despite extensive effort the origin of flux noise is still not well understood. The goal of this work is to identify the source and characterize the property of flux noisein rf SQUID flux qubit through various spectroscopy and time-resolved measurements. Our result show that one can determine all circuit parameters needed for reconstructing qubit Hamiltonian with high accuracy via measurement of macroscopic resonant tunneling (MRT) and photon assisted tunneling (PAT) and that the amount of flux noise in rf SQUID qubits scales linearly with self inductance of the qubits. In addition, we have investigated the dynamics of a three-level flux qubit in incoherent regime. The result demonstrates that treating a multi-level physical qubit, such as the superconducting flux qubit, as an ideal two-level quantum system may be inadequate under certain circumstances.

•Dec 17, 2007•0 citations

Studies of Quantum Transitions of Magnetic Flux in a RF Squid Qubit

Luigi Longobardi

At low temperature and low damping, the magnetic flux of a rf Superconducting QUantum Interference Device (SQUID) acts as a macroscopic quantum variable whose dynamic is described by a double well potential. A rf SQUID consists of a superconducting loop interrupted by a thin insulating barrier, known as a Josephson junction. The modified rf SQUID design discussed in this thesis has independent, in situ, controls that allow varying the barrier height between the potential wells and their relative tilt. This high level of control of the potential together with the capability to implement an experimental setup optimized to reduce coupling to external sources of noise, made this system ideal not only for tests of quantum transition at a macroscopic level, but also as a scalable solid state device for quantum computation. A variety of measurements of quantum phenomena are reported in this thesis, including microwave level spectroscopy, coherent oscillations, and macroscopic resonant tunneling (MRT). These measurements are compared with theoretical models to study the possible sources of decoherence in a rf SQUID qubit. The analysis confirmed that the main source of decoherence is not due to coupling to the external environment, but it can be linked to intrinsic low frequency flux noise. Work from many groups over the last several years has shown that the performance of a superconductive qubit is limited by coupling to spurious defects in the materials used for the device fabrication. In this work we analyze the possibility of using the MRT as a tool for future studies of effects of materials and fabrication process in the realization of improved qubits, and we also explore the feasibility for measurements of quantum phenomena that involve fast pulsing of the potential barrier height.

•Oct 22, 2010•0 citations

Nonlinear resonant behavior of a dispersive readout circuit for a superconducting flux qubit

Janice C. Lee, William D. Oliver, Karl K. Berggren +1 more

A nonlinear resonant circuit comprising a SQUID magnetometer and a shunting capacitor is studied as a readout scheme for a persistent-current qubit. The flux state of the qubit is detected as a change in the Josephson inductance of the SQUID magnetometer, which in turn mediates a shift in the resonant frequency of the readout circuit. The nonlinearity and resulting hysteresis in the resonant behavior are characterized as a function of the power of both the input drive and the associated resonance-peak response. Numerical simulations based on a nonlinear circuit model shows that the observed nonlinearity is dominated by the effect due to an ac flux rather than current bias through the Josephson inductor.

arXiv:cond-mat/0609561•Physical Review B•Apr 11, 2007•23 citations

Tunable Resonator Integrated Magnetometry

Colin Stack, Brian Sears, Aruna Ramanayaka +3 more

The quantum-technology revolution is reshaping computing, sensing, and communication. In magnetometry, recent advances leverage precise control of spin qubits and color centers in solid-state crystals for mesoscopic-scale sensing. Yet at very low temperatures, superconducting sensing technology remains unrivaled because of its non-invasiveness and higher sensitivity. Here we describe a class of superconducting sensors that offers low loss and quantum non-demolition measurement characteristics. We designed and fabricated a superconducting flux-tunable resonator (tRes) in a superconducting chip foundry and matured it to a level that combines the speed of an inductor-capacitor circuit with the flux sensitivity of a superconducting quantum interference device (SQUID) to perform magnetometry at milli-kelvin temperature to investigate targets. We introduce its fundamental functionality readily at MHz magnetic sampling rate, showcase two measurement modalities, and investigate three circuits with gradually increasing complexity to extract target-specific information. The combination of high sensitivity and fast readout characteristics make tRes an attractive and versatile magnetometer.

cond-mat.mes-hallCross-listedarXiv:2606.04914•Jun 4, 2026•0 citations
Recent research in quantum computation with superconducting qubits relies on SQUID magnetometers to distinguish the supercurrent states of the qubits.This poses a new challenge of demanding the measurement SQUID to introduce the least decoherence on the qubits during the measurement process.The SQUID is desired to operate in an unconventional way and be biased at currents significantly below the critical current level.This thesis lays the fundamental work of achieving the above by using the SQUID as a flux-sensitive inductor.The read-out relies on incorporating the SQUID inductor in a resonant circuit, and the state of the qubit is detected from the resonant frequency of the peak.A series of prototype resonant circuits were made from printed circuit boards and tested at room temperature.On-chip high-Q resonant circuits were designed to optimize the signals in the inductance measurements to about ten microvolts.Calculations of the decoherence times based on the spin-boson model were performed and the relaxation time falls in the microsecond regime.
We have implemented a resonant circuit that uses a SQUID as a flux-sensitive Josephson inductor for qubit readout. In contrast to the conventional switching current measurement that generates undesired quasiparticles when the SQUID switches to the voltage state, our approach keeps the readout SQUID biased along the supercurrent branch during the measurement. By incorporating the SQUID inductor in a high-Q resonant circuit, we can distinguish the two flux states of a niobium persistent-current (PC) qubit by observing a shift in the resonant frequency of both the magnitude and the phase spectra. The readout circuit was also characterized in the nonlinear regime to investigate its potential use as a nonlinear amplifier.
Superconducting Josephson junction devices rank among the best candidates for realizing a quantum computer. While the coherent control of quantum dynamics has been demonstrated in these solid-state, macroscopic quantum systems, a major challenge has been to increase the coherence times for these qubits. With an objective to reduce the level of readout-induced decoherence, this thesis work focuses on a resonant readout scheme developed for a niobium persistent-current (PC) qubit. This non-dissipative readout approach detects the flux state of the qubit by sensing a change in the Josephson inductance of a SQUID magnetometer. By incorporating the SQUID inductor in a high-Q resonant circuit, we distinguished the flux states of the qubit as a shift in the resonant frequency at 300 mK. The nonlinearity due to the Josephson inductance has characteristic effects on the resonant behavior of the readout circuit. We observed novel manifestation of this nonlinearity given the high quality factor of the resonance. The readout circuit was characterized in the linear as well as the nonlinear regime for its potential use as a bifurcation amplifier. Numerical simulations based on Josephson-junction circuits were also performed to understand the observed nonlinearity in the resonant behavior.
It is well known that that superconducting qubits based on Josephson junctions have the advantages of scalability and the qubit states are easy to prepare and control. In addition, demonstration of Rabi oscillations in various superconducting circuits shows that superconducting qubits are promising for scalable quantum information processing. However, despite flexibility of design and fabrication, easier to scale up, and fast gate speed, superconducting qubits usually have much shorter decoherence time than trapped ions, NMR etc. due to the relatively strong interactions between qubits and environment. Recent experiments show that low frequency flux noise is the dominant mechanism of decoherence in superconducting flux qubits. However, despite extensive effort the origin of flux noise is still not well understood. The goal of this work is to identify the source and characterize the property of flux noisein rf SQUID flux qubit through various spectroscopy and time-resolved measurements. Our result show that one can determine all circuit parameters needed for reconstructing qubit Hamiltonian with high accuracy via measurement of macroscopic resonant tunneling (MRT) and photon assisted tunneling (PAT) and that the amount of flux noise in rf SQUID qubits scales linearly with self inductance of the qubits. In addition, we have investigated the dynamics of a three-level flux qubit in incoherent regime. The result demonstrates that treating a multi-level physical qubit, such as the superconducting flux qubit, as an ideal two-level quantum system may be inadequate under certain circumstances.
At low temperature and low damping, the magnetic flux of a rf Superconducting QUantum Interference Device (SQUID) acts as a macroscopic quantum variable whose dynamic is described by a double well potential. A rf SQUID consists of a superconducting loop interrupted by a thin insulating barrier, known as a Josephson junction. The modified rf SQUID design discussed in this thesis has independent, in situ, controls that allow varying the barrier height between the potential wells and their relative tilt. This high level of control of the potential together with the capability to implement an experimental setup optimized to reduce coupling to external sources of noise, made this system ideal not only for tests of quantum transition at a macroscopic level, but also as a scalable solid state device for quantum computation. A variety of measurements of quantum phenomena are reported in this thesis, including microwave level spectroscopy, coherent oscillations, and macroscopic resonant tunneling (MRT). These measurements are compared with theoretical models to study the possible sources of decoherence in a rf SQUID qubit. The analysis confirmed that the main source of decoherence is not due to coupling to the external environment, but it can be linked to intrinsic low frequency flux noise. Work from many groups over the last several years has shown that the performance of a superconductive qubit is limited by coupling to spurious defects in the materials used for the device fabrication. In this work we analyze the possibility of using the MRT as a tool for future studies of effects of materials and fabrication process in the realization of improved qubits, and we also explore the feasibility for measurements of quantum phenomena that involve fast pulsing of the potential barrier height.
A nonlinear resonant circuit comprising a SQUID magnetometer and a shunting capacitor is studied as a readout scheme for a persistent-current qubit. The flux state of the qubit is detected as a change in the Josephson inductance of the SQUID magnetometer, which in turn mediates a shift in the resonant frequency of the readout circuit. The nonlinearity and resulting hysteresis in the resonant behavior are characterized as a function of the power of both the input drive and the associated resonance-peak response. Numerical simulations based on a nonlinear circuit model shows that the observed nonlinearity is dominated by the effect due to an ac flux rather than current bias through the Josephson inductor.
The quantum-technology revolution is reshaping computing, sensing, and communication. In magnetometry, recent advances leverage precise control of spin qubits and color centers in solid-state crystals for mesoscopic-scale sensing. Yet at very low temperatures, superconducting sensing technology remains unrivaled because of its non-invasiveness and higher sensitivity. Here we describe a class of superconducting sensors that offers low loss and quantum non-demolition measurement characteristics. We designed and fabricated a superconducting flux-tunable resonator (tRes) in a superconducting chip foundry and matured it to a level that combines the speed of an inductor-capacitor circuit with the flux sensitivity of a superconducting quantum interference device (SQUID) to perform magnetometry at milli-kelvin temperature to investigate targets. We introduce its fundamental functionality readily at MHz magnetic sampling rate, showcase two measurement modalities, and investigate three circuits with gradually increasing complexity to extract target-specific information. The combination of high sensitivity and fast readout characteristics make tRes an attractive and versatile magnetometer.