Indium is a technologically interesting element in the semicoductor and opto-electronics industry. Instead of other usually applied methods, we try to fabricate nano-structures of indium with atom lithography. The simulations show that the feature size of the structures is strongly dependent of the divergence of the indium atomic beam. Thus laser cooling is applied for transverse collimation. For laser cooling of indium, two wavelengths, i.e., 410nm and 451nm, of laser light are used. Light at 410nm is accessed by GaN diode lasers, while light at 451nm is generated by frequency-doubling a Ti-Sa laser emmiting at 902nm. The laser frequnecies are stabilized on the atomic resonance lines with the spectroscopic methods. We observed the optical manipulation of the indium atomic beam with laser light at both wavelengths and even one wavelength at 410nm. The possible mechanisms are also discussed in the thesis.
Indium is a technologically interesting element in the semicoductor and opto-electronics industry. Instead of other usually applied methods, we try to fabricate nano-structures of indium with atom lithography. The simulations show that the feature size of the structures is strongly dependent of the divergence of the indium atomic beam. Thus laser cooling is applied for transverse collimation. For laser cooling of indium, two wavelengths, i.e., 410nm and 451nm, of laser light are used. Light at 410nm is accessed by GaN diode lasers, while light at 451nm is generated by frequency-doubling a Ti-Sa laser emmiting at 902nm. The laser frequnecies are stabilized on the atomic resonance lines with the spectroscopic methods. We observed the optical manipulation of the indium atomic beam with laser light at both wavelengths and even one wavelength at 410nm. The possible mechanisms are also discussed in the thesis.
Laser cooled atomic gases and atomic beams are widely studied samples in experimental research in atomic and optical physics. For the application of ultra cold gases as model systems for e.g. quantum many particle systems, the atomic species is not very important. Thus this field is dominated by alkaline, earthalkaline elements which are easily accessible with conventional laser sources and have convenient closed cooling transition. On the otherhand, laser cooled atoms may also be interesting for technological applications, for instance for the creation of novel materials by atomic nanofabrication (ANF). There it will be important to use technologically relevant materials. As an example, using group III atoms of the periodical table in ANF may open a route to generate fully 3D structured composite materials. The minimal requirement in such an ANF experiment is the collimation of an atomic beam which is accessible by one dimensional laser cooling. In this dissertation, I describe transverse laser cooling of an Indium atomic beam. For efficient laser cooling on a cycling transition, I have built a tunable, continuous-wave coherent ultraviolet source at 326 nm based on frequency tripling. For this purpose, two independent high power Yb-doped fiber amplifiers for the generation of the fundamental radiation at 977 nm have been constructed. I have observed sub-Doppler transverse laser cooling of an Indium atomic beam on a cycling transition of In by introducing a polarization gradient in the linear-perpendicular-linear configuration. The transverse velocity spread of a laser-cooled In atomic beam at full width at half maximum was achieved to be 13.5 ± 3.8 cm/s yielding a full divergence of only 0.48 ± 0.13 mrad. In addition, nonlinear spectroscopy of a 3-level, Lambda-type level system driven by a pump and a probe beam has been investigated in order to understand the absorption line shapes used as a frequency reference in a previous two-color spectroscopy experiment. For the analysis of this atomic system, I have applied a density matrix theory providing an excellent basis for understanding the observed line shapes.
Atom lithography (AL) is one of the interesting applications in atom optics where the atomic motion is controlled by laser beam or magnetic force (Meschede and Metcalf, 2003). In our group, we have focused on the AL using indium atoms which promises application in semiconductor physics. A standing-wave light field can be used as micro-lens array to focus atoms onto a substrate. Due to the small dipole force, a well-collimated atomic beam is required for AL. The collimation can be realized by transverse laser cooling.
We developed a laser-beam-controlled atom-manipulation system to deposit nanometric structure of atoms on a substrate. Atom beam of chromium is thermally evaporated and collimated with Doppler cooling technique using frequency-tuned laser diode. The gradient force is exerted on atoms by a standing wave over the substrate, and atoms are trapped in a low potential region of the standing wave. Consequently, a series of lines are formed on the substrate with the same periodicity to the standing wave. We present the analysis of trajectories of atoms in the light force potential to find conditions of the laser power, the sign and the degree of the detuning of the laser frequency from the resonance frequency of the atom, to reduce the width of the structure.
Direct-write atom lithography is a technique in which highly periodic nanostructures are directly deposited on a substrate by patterning an atomic beam with a standing light wave, tuned near a resonance frequency of the corresponding atom. In this thesis an extension of this technique for the production of ferromagnetic nano- structures is investigated. Of all ferromagnetic elements Fe is the most suitable to per- form atom lithography. Light with a wavelength of 372 nm is needed to produce Fe nanostructures by atom lithography. Also, the atomic beam should be highly collimated, for which laser cooling is commonly used. For this purpose, a frequency doubled Ti:S laser tuned to 744 nm is constructed, capable of producing more than 100 mW of light at a wavelength of 372 nm. Laser cooling requires a laser with a frequency stability better than the natural linewidth of the atom. To meet this requirement, the laser is locked on the atomic transition by means of polarization spectroscopy on a hollow cathode discharge cell. The discharge cell produces a sufficient density of ground state Fe atoms at a temperature which is more than a factor of two lower than the temperature necessary to produce that density in a thermal cell. With this technique the laser is locked stable within 0.2 MHz for hours. A laser cooling simulation based on the semiclassical approach is presented. Although the intention was to simulate laser cooling of Fe with this code, for the commonly used pxpy polarization gradient configuration an analysis of the simulation results shows that the semiclassical approach is only valid for transitions with recoil parameters ¿r on the order of 10¡4 or less. For the standard laser cooling transitions only the transitions in Rb and Cs satisfy this condition. A drastic reduction in calculation time compared to quantum Monte-Carlo calculations is to be expected for these transitions by implementing an analytical approach to the long-term contribution of the diffusion coefficient. For Fe, full quantum Monte-Carlo calculations are necessary. Laser cooling of Fe on the 372 nm transition has been studied experimentally. This transition, although the only one realistically available, is far from perfect for laser cooling, as it is not a fully closed transition: it has a leak ratio of approximately 1/240 to other states. Nevertheless, a collimation of aRMS = 0.17 mrad could be achieved by laser cooling. However, contrary to the normally obtained central beam flux increase, the ground state atom flux decreased to approximately 70 % of the non-cooled value. Because of both the complexity of the laser cooling setup and the restrictions in perfor- mance, we have also attempted to produce Fe nanostructures without using laser cooling techniques, but simply relying on geometrical collimation of the atomic beam. In this way, Fe nanolines are deposited with a pitch of 186 nm, a FWHM width of 50 nm, and a height of up to 6 nm. This opens the way for applying direct-write atom lithography to a wide variety of elements. In a MOKE (Magneto-Optical Kerr effect)-setup we are able to verify that the deposited Fe-layer is ferromagnetic. However, the magnetic anisotropy due to the presence of the nanolines can not be detected with a MOKE-setup or a MFM (Magnetic Force Microscope). In contrast, the magnetization of background-free nano- lines, deposited through a mechanical mask with a pitch of 744 nm and a FWHM of
Atom lithography is a technique in which a light field is used to pattern an atomic beam. This patterned flux is then deposited onto a substrate, resulting in a nanostructured thin film. The smallest structures that have been made thus far using this technique are around 30 nm wide. This thesis investigates the technique, expanding its possibilities. The work-horse for the development of atom lithography has been Cr, as this transition metal atom has a closed transition in a wavelength range that is accessible to dye lasers. We extend the technique to Fe, the first ferromagnetic element to be used for atom lithography. The setup that was used to do this experiment is described, along with its critical design parameters. We present nanostructures that are typically 50 nm wide, and up to 4 nm high. The spacing between the nanolines is 186.05 nm. The nanostructure profile is compared to that of a simulated deposition process, and found to match. To the authors’ knowledge, this is the first demonstration of direct write atom lithography without laser cooling. A preliminary incursion into the magnetic properties of the nanostructures deposited is presented. In addition to giving an overview of the general ferromagnetic properties that might be expected, a deeper investigation of the magnetic anisotropy of the nanostructures deposited in this experiment is given. Novel resonant light masks are used in an experiment performed at the University of Konstanz (Germany). These light masks, using exactly instead of nearly resonant light, reveal some intriguing quantum mechanical effects. The most important of these features is the possibility to place structures closer together – at quarter wavelength spacings rather than half-wavelength intervals. Finally, the influence of surface diffusion on the structures obtained in an atom lithography experiment is investigated using kinetic Monte Carlo simulations. Several diffusion limiting effects are investigated; the influence of small amounts of residual reactive background gas is found to describe the experimental observations.
Summary form only given. Laser focusing of neutral atoms is a unique approach for fabricating periodic small structures. In a standing wave formed by two counter-propagating laser beams, the radiation force acts as a sequence of cylindrical lenses that focus the atoms into a periodic array of parallel lines during deposition onto a substrate. In this way, a pattern is written onto the substrate without the use of any masks. To minimize the feature width on the substrate, the atoms entering the focusing laser must be highly collimated transversely by optical cooling.