Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

An SNS technology process for ramp junction based digital superconducting circuits

Daniel Hagedorn, M. Khabipov, R. Dolata, F.-I. Buchholz, J. Niemeyer

Published Jun 1, 2003• 6 citations
Publisher

Abstract

The SNS (Nb/HfTi/Nb) ramp junction technology process has been improved for digital superconducting circuit operation. DC interferometers were realized on an isolated superconducting ground plane, connections being realized through windows in the insulation layers. The inductances of superconducting Nb striplines (widths w down to the sub-/spl mu/m range) were measured. For a 250 nm SiO/sub 2//Nb-oxide insulation layer, the sheet inductances of striplines were determined at 0.382 /spl plusmn/ 0.009, 0.340 /spl plusmn/ 0.005, and 0.293 /spl plusmn/ 0.008 pH (stripline widths: 1.5, 1.0, 0.54 /spl mu/m) and compared with data calculated by different inductance evaluation programs. The Josephson junctions used in the interferometers exhibit a critical current density of j/sub C/=525 kA/cm/sup 2/ and a characteristic voltage of V/sub C/=95 /spl mu/V. The design of an RSFQ converter circuit was developed on the basis of SNS ramp junction technology. For circuit applications the critical current density j/sub C/ was set to 150 kA/cm/sup 2/.

DOI
10.1109/tasc.2003.814164

Related papers

SINIS process development for integrated circuits with characteristic voltages exceeding 250 μV

D Balashov, M. Khabipov, F.-I. Buchholz +1 more

At PTB, the fabrication process in Nb-Al/Al/sub x/O/sub y//Al/Al/sub x/O/sub y//Al-Nb SINIS multilayer technology has been improved to raise the characteristic voltage of SINIS two-tunnel Josephson junctions up to V/sub C/=I/sub C/R/sub n/=245 /spl mu/V. The process has been realized in LTS implementation. Various sets of the test wafers and wafers containing dc/SFQ and SFQ/dc converters, Josephson transmission lines, and T-flipflop circuits were fabricated and measured. The critical current densities of the junctions have been varied in the range from 70 A/cm/sup 2/ to 2.2 kA/cm/sup 2/ with corresponding characteristic voltages of V/sub C/=55 /spl mu/V and 245 /spl mu/V at the temperature of 4.2 K. The junctions show nearly hysteresis-free behaviour (less than 15%), the intra-wafer parameter spread is smaller than /spl plusmn/10%. RSFQ circuits have been realized with operation margins of the bias currents larger than /spl plusmn/20%.

IEEE Transactions on Applied Superconductivity•Mar 1, 2001•11 citations

Superconductor-normal metal-superconductor process development for the fabrication of small Josephson junctions in ramp type configuration

R. Pöpel, Daniel Hagedorn, Thomas Weimann +2 more

At PTB, a fabrication process has been developed in SNS Nb/PdAu/Nb technology for the verification of small Josephson junctions (JJs) in the deep sub-micron range to enable the implementation of JJs as active elements in highly integrated superconducting circuits. Two steps of this technological development are described with regard to appropriately designed circuit layouts of JJ series arrays (JJAs), the first one in a conventional window type junction (WTJ) configuration and the second one in a ramp type junction (RTJ) configuration. Test circuits of JJAs containing up to 10 000 JJs have been fabricated and experimentally tested. In WTJ configuration, the circuits proved to be sensitive to external perturbing effects affecting the stability of circuit operation. In contrast to that, in RTJ configuration, the circuits realized showed correct function and a high grade of reliability of operation. To produce RTJ circuits, the technology parameters have been set to realize JJs with contact areas of A = 0.25 µm × 1.3 µm. At a thickness of the PdAu normal metal layer of d = 40 nm, the values achieved for the critical current density and for the product of critical current and normal state resistance are about jc = 200 kA cm-2 and about Ic RN = 21 µV.

Superconductor Science and Technology•Jan 19, 2000•19 citations

SNS junction on Nb-Ti base for microwave circuits

M. Schubert, Ludwig Fritzsch, G. Wende +1 more

Superconductor-normal metal-superconductor (SNS) junctions are well-suited for large-scale integrated superconducting circuits. Potential applications are programmable voltage standards, digital-to-analog converters and large-scale RSFQ circuits. The application of SNS junctions provides some advantages, e.g. a simplified fabrication technology and reduced parasitic inductances. But it requires a technological process with dimensions down to the submicrometer region to achieve sufficiently high characteristic voltages I/sub C/R/sub N/. In our process the normal metal interlayer is titanium. Therefore the sidewall insulation of the junctions can be made by anodization, as it is known from the Nb-Al technology. Nb-Ti-Nb Josephson junctions and junction arrays were fabricated down to the submicrometer range with I/sub C/R/sub N/ values up to 87 microvolt depending on the titanium thickness. Their measured critical currents have a small spread of about 10 percent. Shapiro steps are observed under the influence of microwave irradiation. For the application of such junctions in a programmable Josephson voltage standard a new type of microwave circuit using coplanar strips is proposed and successfully tested in 10 V SIS circuits.

IEEE Transactions on Applied Superconductivity•Mar 1, 2001•12 citations

High-frequency performance of RSFQ circuits realized in SINIS technology

M. Khabipov, D Balashov, F.-I. Buchholz +1 more

The paper presents the determination of the high-frequency performance of Rapid Single Flux Quantum (RSFQ) circuits fabricated in superconductor-insulator-normal metal-insulator-superconductor (SINIS) technology. Circuits of different designs have been realized and were experimentally investigated, including specially designed T flip-flop (TFF) structures and circuits consisting of a switch terminated in Josephson transmission lines. For TFF circuits, the operational functionality was investigated in the frequency range from dc up to nearly 200 GHz. Two frequency domains were found. In the first domain, ranging up to frequencies of 80 GHz (f/sub C//spl cong/Y/sub C///spl Phi//sub 0/), correct digital operation of the device was ascertained. Beyond this range a second domain was found, ranging to nearly 200 GHz, for which quasi-analog frequency dividing is assumed. The bias current margins are /spl plusmn/30% at 40 GHz and /spl plusmn/15% between 130 GHz and 200 GHz. For circuits consisting of a switch, the operational functionality was proved in the frequency range from dc up to 50 GHz, with bias current margins of more than /spl plusmn/20%. The critical current density of the circuits is j/sub C//spl cong/750 A/cm/sup 2/. The smallest junction area is about A=12 /spl mu/m/sup 2/, and the characteristic voltage is V/sub C/=170 /spl mu/V.

IEEE Transactions on Applied Superconductivity•Mar 1, 2001•7 citations

SNS and SIS Josephson junctions with dimensions down to the submicron region prepared by a unified technology

Ludwig Fritzsch, H. Elsner, M. Schubert +1 more

Several applications of Josephson junctions (JJs) in low-temperature superconducting circuits such as programmable voltage standards and SFQ logical circuits or SQUID sensors require JJs with sub-µm dimensions. A method for preparing superconductor-isolator-superconductor (SIS) JJs as well as superconductor-normal metal-superconductor (SNS) JJs was developed which allows the preparation of both types of junctions by nearly the same technological process. Titanium is used as the normal metal for the SNS JJ. Ti can be anodically oxidized and a technology similar to the well-tried Nb-Al technology for SIS JJs can be applied to the SNS system, too. By electron-beam exposure of a negative deep UV photoresist (ma-N 2400) a stable resist mask is generated which has to withstand the following three self-aligned process steps: etching of the Nb counterelectrode by RIE, isolation by anodization and lifting of a SiO planarization layer. By this process SNS (Nb-Ti-Nb) and SIS (Nb-Al/AlO x -Nb) Josephson junctions with smallest junction areas of 0.49 µm 2 were prepared and characterized by dc measurements and under the influence of microwave irradiation. The Nb-Ti-Nb junctions have I c R n products of 87 µV. They can be used for programmable Josephson voltage standard circuits at frequencies of 70 GHz.

Superconductor Science and Technology•Nov 1, 1999•9 citations

Next generation Nb superconductor integrated circuit process

L.A. Abelson, Raffi Elmadjian, G.L. Kerber

We have developed our next generation Nb integrated circuit process which offers higher performance, particularly for SFQ-type logic, and increased density compared to our present 2000 A/cm/sup 2/ foundry process. The new process is based on our existing Nb foundry process, but has been optimized to utilize more of the sub-micron alignment and exposure capabilities of our optical lithography tools. Minimum linepitch and junction size have been reduced to 2.5 /spl mu/m (from 4 /spl mu/m) and 1.75 /spl mu/m (from 2.5 /spl mu/m), respectively, and J/sub c/ has been increased to 4000 A/cm/sup 2/. These goals have been achieved by an overall reduction in layer thicknesses, implementation of SF/sub 6/ dry etch for metal line definition, and optimization of the photolithography process. The new process offers lower inductance wiring and substantially lower parasitic circuit inductances compared with the existing Nb foundry process. In this paper, we discuss these improvements and report parametric test data for devices fabricated in this process.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•14 citations
The SNS (Nb/HfTi/Nb) ramp junction technology process has been improved for digital superconducting circuit operation. DC interferometers were realized on an isolated superconducting ground plane, connections being realized through windows in the insulation layers. The inductances of superconducting Nb striplines (widths w down to the sub-/spl mu/m range) were measured. For a 250 nm SiO/sub 2//Nb-oxide insulation layer, the sheet inductances of striplines were determined at 0.382 /spl plusmn/ 0.009, 0.340 /spl plusmn/ 0.005, and 0.293 /spl plusmn/ 0.008 pH (stripline widths: 1.5, 1.0, 0.54 /spl mu/m) and compared with data calculated by different inductance evaluation programs. The Josephson junctions used in the interferometers exhibit a critical current density of j/sub C/=525 kA/cm/sup 2/ and a characteristic voltage of V/sub C/=95 /spl mu/V. The design of an RSFQ converter circuit was developed on the basis of SNS ramp junction technology. For circuit applications the critical current density j/sub C/ was set to 150 kA/cm/sup 2/.
At PTB, the fabrication process in Nb-Al/Al/sub x/O/sub y//Al/Al/sub x/O/sub y//Al-Nb SINIS multilayer technology has been improved to raise the characteristic voltage of SINIS two-tunnel Josephson junctions up to V/sub C/=I/sub C/R/sub n/=245 /spl mu/V. The process has been realized in LTS implementation. Various sets of the test wafers and wafers containing dc/SFQ and SFQ/dc converters, Josephson transmission lines, and T-flipflop circuits were fabricated and measured. The critical current densities of the junctions have been varied in the range from 70 A/cm/sup 2/ to 2.2 kA/cm/sup 2/ with corresponding characteristic voltages of V/sub C/=55 /spl mu/V and 245 /spl mu/V at the temperature of 4.2 K. The junctions show nearly hysteresis-free behaviour (less than 15%), the intra-wafer parameter spread is smaller than /spl plusmn/10%. RSFQ circuits have been realized with operation margins of the bias currents larger than /spl plusmn/20%.
At PTB, a fabrication process has been developed in SNS Nb/PdAu/Nb technology for the verification of small Josephson junctions (JJs) in the deep sub-micron range to enable the implementation of JJs as active elements in highly integrated superconducting circuits. Two steps of this technological development are described with regard to appropriately designed circuit layouts of JJ series arrays (JJAs), the first one in a conventional window type junction (WTJ) configuration and the second one in a ramp type junction (RTJ) configuration. Test circuits of JJAs containing up to 10 000 JJs have been fabricated and experimentally tested. In WTJ configuration, the circuits proved to be sensitive to external perturbing effects affecting the stability of circuit operation. In contrast to that, in RTJ configuration, the circuits realized showed correct function and a high grade of reliability of operation. To produce RTJ circuits, the technology parameters have been set to realize JJs with contact areas of A = 0.25 µm × 1.3 µm. At a thickness of the PdAu normal metal layer of d = 40 nm, the values achieved for the critical current density and for the product of critical current and normal state resistance are about jc = 200 kA cm-2 and about Ic RN = 21 µV.
Superconductor-normal metal-superconductor (SNS) junctions are well-suited for large-scale integrated superconducting circuits. Potential applications are programmable voltage standards, digital-to-analog converters and large-scale RSFQ circuits. The application of SNS junctions provides some advantages, e.g. a simplified fabrication technology and reduced parasitic inductances. But it requires a technological process with dimensions down to the submicrometer region to achieve sufficiently high characteristic voltages I/sub C/R/sub N/. In our process the normal metal interlayer is titanium. Therefore the sidewall insulation of the junctions can be made by anodization, as it is known from the Nb-Al technology. Nb-Ti-Nb Josephson junctions and junction arrays were fabricated down to the submicrometer range with I/sub C/R/sub N/ values up to 87 microvolt depending on the titanium thickness. Their measured critical currents have a small spread of about 10 percent. Shapiro steps are observed under the influence of microwave irradiation. For the application of such junctions in a programmable Josephson voltage standard a new type of microwave circuit using coplanar strips is proposed and successfully tested in 10 V SIS circuits.
The paper presents the determination of the high-frequency performance of Rapid Single Flux Quantum (RSFQ) circuits fabricated in superconductor-insulator-normal metal-insulator-superconductor (SINIS) technology. Circuits of different designs have been realized and were experimentally investigated, including specially designed T flip-flop (TFF) structures and circuits consisting of a switch terminated in Josephson transmission lines. For TFF circuits, the operational functionality was investigated in the frequency range from dc up to nearly 200 GHz. Two frequency domains were found. In the first domain, ranging up to frequencies of 80 GHz (f/sub C//spl cong/Y/sub C///spl Phi//sub 0/), correct digital operation of the device was ascertained. Beyond this range a second domain was found, ranging to nearly 200 GHz, for which quasi-analog frequency dividing is assumed. The bias current margins are /spl plusmn/30% at 40 GHz and /spl plusmn/15% between 130 GHz and 200 GHz. For circuits consisting of a switch, the operational functionality was proved in the frequency range from dc up to 50 GHz, with bias current margins of more than /spl plusmn/20%. The critical current density of the circuits is j/sub C//spl cong/750 A/cm/sup 2/. The smallest junction area is about A=12 /spl mu/m/sup 2/, and the characteristic voltage is V/sub C/=170 /spl mu/V.
Several applications of Josephson junctions (JJs) in low-temperature superconducting circuits such as programmable voltage standards and SFQ logical circuits or SQUID sensors require JJs with sub-µm dimensions. A method for preparing superconductor-isolator-superconductor (SIS) JJs as well as superconductor-normal metal-superconductor (SNS) JJs was developed which allows the preparation of both types of junctions by nearly the same technological process. Titanium is used as the normal metal for the SNS JJ. Ti can be anodically oxidized and a technology similar to the well-tried Nb-Al technology for SIS JJs can be applied to the SNS system, too. By electron-beam exposure of a negative deep UV photoresist (ma-N 2400) a stable resist mask is generated which has to withstand the following three self-aligned process steps: etching of the Nb counterelectrode by RIE, isolation by anodization and lifting of a SiO planarization layer. By this process SNS (Nb-Ti-Nb) and SIS (Nb-Al/AlO x -Nb) Josephson junctions with smallest junction areas of 0.49 µm 2 were prepared and characterized by dc measurements and under the influence of microwave irradiation. The Nb-Ti-Nb junctions have I c R n products of 87 µV. They can be used for programmable Josephson voltage standard circuits at frequencies of 70 GHz.
We have developed our next generation Nb integrated circuit process which offers higher performance, particularly for SFQ-type logic, and increased density compared to our present 2000 A/cm/sup 2/ foundry process. The new process is based on our existing Nb foundry process, but has been optimized to utilize more of the sub-micron alignment and exposure capabilities of our optical lithography tools. Minimum linepitch and junction size have been reduced to 2.5 /spl mu/m (from 4 /spl mu/m) and 1.75 /spl mu/m (from 2.5 /spl mu/m), respectively, and J/sub c/ has been increased to 4000 A/cm/sup 2/. These goals have been achieved by an overall reduction in layer thicknesses, implementation of SF/sub 6/ dry etch for metal line definition, and optimization of the photolithography process. The new process offers lower inductance wiring and substantially lower parasitic circuit inductances compared with the existing Nb foundry process. In this paper, we discuss these improvements and report parametric test data for devices fabricated in this process.