Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

RSFQ multiplexer and demultiplexer

L Zheng, Nobuyuki Yoshikawa, Jiaqi Deng, Xiangchao Meng, Stephen R. Whiteley, T. Van Duzer

Published Jun 1, 1999• 18 citations
Publisher

Abstract

An 1:8 RSFQ demultiplexer (DEMUX) and an 8:1 RSFQ multiplexer (MUX) were designed, simulated and optimized to operate at about 20 GHz. Both the inputs and outputs of the DEMUX are complementary dual-rail signals. The basic 2-bit DEMUX module is a self-clocked dual-rail T flip-flop. This DEMUX has a simpler structure than an earlier version of a data-driven-self-timed (DDST) DEMUX developed in our laboratory; however its simulated dc bias margin is (-20%, +20%), which is lower than the more complex device (-29%, +29%). The MUX takes lower data rate single-rail inputs and combines them sequentially into a single output. The complementary output is recovered from the output itself to facilitate interfacing to other dual-rail circuits on chip. The calculated dc bias margin is (-30 %, +28%). Circuit functionality is verified for the 2-bit MUX and the 2-bit DEMUX at low speed. An on-chip high-speed test system is designed to evaluate operation of the MUX and DEMUX at 20 GHz. The circuits are fabricated using a 1 kA/cm/sup 2/ niobium process at both UCB and HYPRES.

DOI
10.1109/77.783737

Related papers

Simulation and 18 Gb/s testing of a data-driven self-timed RSFQ demultiplexer

Nobuyuki Yoshikawa, Z.J. Deng, Stephen R. Whiteley +1 more

We have developed a data-driven self-timed (DDST) rapid-single-flux-quantum (RSFQ) demultiplexer (demux) for the interface between on-chip high-speed RSFQ circuits and off-chip low-speed circuits. In order to eliminate the timing issue in a synchronous clocking system we employed the DDST architecture, where a clock signal is localized within a 2-bit basic demux module and dual rail lines are used to transfer the timing information between the modules. A larger demux can be produced simply by connecting the 2-bit modules in a tree structure. The DDST demux was designed for 10 Gb/s operation with sufficient dc bias margin using HYPRES 1 kA/cm/sup 2/ Nb process. We have successfully tested operation of the 2-bit demux up to 18 GHz using the DDST on-chip high-speed test system which was developed in our group.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•9 citations

High-speed asynchronous data multiplexing/demultiplexing

Alex F. Kirichenko

High-speed data acquisition and communication systems require fast multiplexing and demultiplexing of data. We are developing novel multiplexer/demultiplexer circuits using a dual-rail approach. A single cell of the demultiplexer is a toggle type B flip-flop. The demultiplexer operates at 95 GHz and its performance does not depend on the demultiplexing ratio. The dual-rail technique avoids racing between data and clock signals. The multiplexer circuit is based on RS type B flip-flops and works up to 60 GHz. The circuits are implemented in HYPRES' standard Nb process with a critical current density of 1.0 KA/cm/sup 2/.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•10 citations

High-speed operation of demultiplexer up to 56 GHz

Futoshi Furuta, K. Saitoh, Kazumasa Takagi

A 1-to-4 demultiplexer (DEMUX) was designed based on Single Flux Quantum (SFQ) circuitry and high-speed operation was confirmed using on-chip testing. The circuit was designed with a binary-tree structure to enable high-speed operation. We also investigated timing between clock and data signals in detail. Monte Carlo simulation was applied to vary the design parameters pseudo-randomly and the spread of timing was obtained by circuit simulation. Even if the circuit parameters varied as a result of the fabrication process, proper timing was maintained by optimizing the length of Josephson transmission line. The 1-to-4 DEMUX we fabricated distributed data signals correctly at operating frequencies up to 56 GHz with a bias margin of /spl plusmn/7%.

IEEE Transactions on Applied Superconductivity•Jun 1, 2003•10 citations

High-speed operation of RSFQ circuits up to 30 GHz

Futoshi Furuta, Yasutoshi Suzuki, H. Hasegawa +3 more

We have experimentally demonstrated high-speed operation of RSFQ circuits using on-chip testing system and confirmed normal operation up to 30 GHz. The system includes high-frequency pulse generators and shift registers (SRs) serving as an interface circuit between high-speed internal signals and low-speed external signals. We adopted two ladder-type pulse generators. One generates clock pulses of 10 GHz and the other generates 25 GHz. By increasing bias currents of JTLs, clock pulses can be generated at higher frequency. By using the system, an SR and a T flip-flop (TFF) gate are examined. The circuits were fabricated by NEC's standard process based on Nb/AlO x /Nb junction technology with J c = 2.5 kA cm -2 . We optimized circuit parameters by using Monte Carlo simulation. In addition, the effect of parasitic inductances can be reduced by decreasing I c . As a result, the systems for SR and TFF worked correctly up to 30 GHz and 27.5 GHz, respectively. The SR and TFF have wide bias margins of ±39% and ±20%, respectively. We confirmed that the bias margins of the SR are independent of operation frequency. The limits of operation frequency are thought to be much higher than 30 GHz.

Superconductor Science and Technology•Nov 1, 1999•8 citations

4-bit rapid single-flux-quantum decoder

Alex F. Kirichenko, Vasili K. Semenov, Ying Ki Kwong +1 more

We describe the design of a fast single-flux-quantum decoder which can be used, e.g., in fast RAMs, general-purpose microprocessors, and communication channel switches. The core of the circuit is a tree of the single-bit SFQ demultiplexer with toggle (rather than the reset-set) control. Three new RSFQ cells: the demultiplexer, D flip-flop with complementary outputs, and serial XOR with large parameter tolerances (dc bias margins of /spl plusmn/25%, /spl plusmn/26%, and /spl plusmn/27%, respectively) have been developed for the decoder project. We have designed the first 16-bit prototype of the decoder for 1-kA/cm/sup 2/ niobium-trilayer technology and tested it at low frequencies. The circuit was completely operable except for 3 (of 16) output SFQ/DC converters. Simulations show that the circuit should allow data rate in excess of 60 Gbit/s and channel switching time below 20 ps.>

IEEE Transactions on Applied Superconductivity•Jun 1, 1995•28 citations

An asynchronous rapid single-flux-quantum demultiplexer based on dual-rail information coding

Boyko Dimov, M. Khabipov, D Balashov +4 more

We present a novel asynchronous RSFQ demultiplexer based on dual-rail information coding. The electrical scheme of the circuit is designed and optimized to maximize the margins of its elements and to improve the fabrication yield. This optimized scheme has been fabricated with the 4 µm 1 kA cm−2 Nb/Al2O3–Al/Nb technology of PTB-Braunschweig. The demultiplexer has been tested with different samples of the low-speed incoming data stream and in all cases a correct circuit functionality has been observed.

Superconductor Science and Technology•Apr 5, 2005•1 citation
An 1:8 RSFQ demultiplexer (DEMUX) and an 8:1 RSFQ multiplexer (MUX) were designed, simulated and optimized to operate at about 20 GHz. Both the inputs and outputs of the DEMUX are complementary dual-rail signals. The basic 2-bit DEMUX module is a self-clocked dual-rail T flip-flop. This DEMUX has a simpler structure than an earlier version of a data-driven-self-timed (DDST) DEMUX developed in our laboratory; however its simulated dc bias margin is (-20%, +20%), which is lower than the more complex device (-29%, +29%). The MUX takes lower data rate single-rail inputs and combines them sequentially into a single output. The complementary output is recovered from the output itself to facilitate interfacing to other dual-rail circuits on chip. The calculated dc bias margin is (-30 %, +28%). Circuit functionality is verified for the 2-bit MUX and the 2-bit DEMUX at low speed. An on-chip high-speed test system is designed to evaluate operation of the MUX and DEMUX at 20 GHz. The circuits are fabricated using a 1 kA/cm/sup 2/ niobium process at both UCB and HYPRES.
We have developed a data-driven self-timed (DDST) rapid-single-flux-quantum (RSFQ) demultiplexer (demux) for the interface between on-chip high-speed RSFQ circuits and off-chip low-speed circuits. In order to eliminate the timing issue in a synchronous clocking system we employed the DDST architecture, where a clock signal is localized within a 2-bit basic demux module and dual rail lines are used to transfer the timing information between the modules. A larger demux can be produced simply by connecting the 2-bit modules in a tree structure. The DDST demux was designed for 10 Gb/s operation with sufficient dc bias margin using HYPRES 1 kA/cm/sup 2/ Nb process. We have successfully tested operation of the 2-bit demux up to 18 GHz using the DDST on-chip high-speed test system which was developed in our group.
High-speed data acquisition and communication systems require fast multiplexing and demultiplexing of data. We are developing novel multiplexer/demultiplexer circuits using a dual-rail approach. A single cell of the demultiplexer is a toggle type B flip-flop. The demultiplexer operates at 95 GHz and its performance does not depend on the demultiplexing ratio. The dual-rail technique avoids racing between data and clock signals. The multiplexer circuit is based on RS type B flip-flops and works up to 60 GHz. The circuits are implemented in HYPRES' standard Nb process with a critical current density of 1.0 KA/cm/sup 2/.
A 1-to-4 demultiplexer (DEMUX) was designed based on Single Flux Quantum (SFQ) circuitry and high-speed operation was confirmed using on-chip testing. The circuit was designed with a binary-tree structure to enable high-speed operation. We also investigated timing between clock and data signals in detail. Monte Carlo simulation was applied to vary the design parameters pseudo-randomly and the spread of timing was obtained by circuit simulation. Even if the circuit parameters varied as a result of the fabrication process, proper timing was maintained by optimizing the length of Josephson transmission line. The 1-to-4 DEMUX we fabricated distributed data signals correctly at operating frequencies up to 56 GHz with a bias margin of /spl plusmn/7%.
We have experimentally demonstrated high-speed operation of RSFQ circuits using on-chip testing system and confirmed normal operation up to 30 GHz. The system includes high-frequency pulse generators and shift registers (SRs) serving as an interface circuit between high-speed internal signals and low-speed external signals. We adopted two ladder-type pulse generators. One generates clock pulses of 10 GHz and the other generates 25 GHz. By increasing bias currents of JTLs, clock pulses can be generated at higher frequency. By using the system, an SR and a T flip-flop (TFF) gate are examined. The circuits were fabricated by NEC's standard process based on Nb/AlO x /Nb junction technology with J c = 2.5 kA cm -2 . We optimized circuit parameters by using Monte Carlo simulation. In addition, the effect of parasitic inductances can be reduced by decreasing I c . As a result, the systems for SR and TFF worked correctly up to 30 GHz and 27.5 GHz, respectively. The SR and TFF have wide bias margins of ±39% and ±20%, respectively. We confirmed that the bias margins of the SR are independent of operation frequency. The limits of operation frequency are thought to be much higher than 30 GHz.
We describe the design of a fast single-flux-quantum decoder which can be used, e.g., in fast RAMs, general-purpose microprocessors, and communication channel switches. The core of the circuit is a tree of the single-bit SFQ demultiplexer with toggle (rather than the reset-set) control. Three new RSFQ cells: the demultiplexer, D flip-flop with complementary outputs, and serial XOR with large parameter tolerances (dc bias margins of /spl plusmn/25%, /spl plusmn/26%, and /spl plusmn/27%, respectively) have been developed for the decoder project. We have designed the first 16-bit prototype of the decoder for 1-kA/cm/sup 2/ niobium-trilayer technology and tested it at low frequencies. The circuit was completely operable except for 3 (of 16) output SFQ/DC converters. Simulations show that the circuit should allow data rate in excess of 60 Gbit/s and channel switching time below 20 ps.>
We present a novel asynchronous RSFQ demultiplexer based on dual-rail information coding. The electrical scheme of the circuit is designed and optimized to maximize the margins of its elements and to improve the fabrication yield. This optimized scheme has been fabricated with the 4 µm 1 kA cm−2 Nb/Al2O3–Al/Nb technology of PTB-Braunschweig. The demultiplexer has been tested with different samples of the low-speed incoming data stream and in all cases a correct circuit functionality has been observed.