Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Local Resistivity and the Current-Voltage Characteristics of Hot Electron Bolometer Mixers

Merlijn Hajenius, R. Barends, J. R. Gao, T. M. Klapwijk, J. J. A. Baselmans, Andrey M. Baryshev, B. Voronov, Gregory N Gol'tsman

Published Jun 1, 2005• 15 citations
Publisher

Abstract

Hot-electron bolometer devices, used successfully in low noise heterodyne mixing at frequencies up to 2.5 THz, have been analyzed. A distributed temperature numerical model of the NbN bridge, based on a local electron and a phonon temperature, is used to model pumped IV curves and understand the physical conditions during the mixing process. We argue that the mixing is predominantly due to the strongly temperature dependent local resistivity of the NbN. Experimentally we identify the origins of different transition temperatures in a real HEB device, suggesting the importance of the intrinsic resistive transition of the superconducting bridge in the modeling.

DOI
10.1109/tasc.2005.849887

Related papers

Improved superconducting hot-electron bolometer devices for the THz range

T. M. Klapwijk, R. Barends, J. R. Gao +2 more

Improved and reproducible heterodyne mixing (noise temperatures of 950 K at 2.5 THz) has been realized with NbN based hot-electron superconducting devices with low contact resistances. A distributed temperature numerical model of the NbN bridge, based on a local electron and a phonon temperature, has been used to understand the physical conditions during the mixing process. We find that the mixing is predominantly due to the exponential rise of the local resistivity as a function of electron temperature.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Oct 8, 2004•18 citations

A Large Signal Model for Phonon-Cooled Hot-Electron Bolometric Mixers for THz Frequency Applications

H. Merkel, E. Kollberg, K. S. Yngvesson

Phonon cooled hot electron bolometers (HEB) show smaller noise temperatures in mixer applications above 1THz compared to Schottky diodes or SIS devices. To determine the optimal bias point for maximum IF bandwidth and lowest noise of a FEB detailed understandin g of the current-voltage characteristic is indispensable. A complete nonlinear model for a hot electron bolometric (HEB) mixer is derived. The dynamic resistance of a superconducting film is calculated under stron g demagnetization conditions. The resistance is modeled due to vortex flow and phase slip lines. Self heating gives rise to normal domains in the film. In addition the resistance due to thermally activated flux creep and thermal fluctuations is taken into account. All these relations form a large si gnal model for the iv-characteristics and the bias points of the device. A small signal linearization yields then conversion gain and noise temperatures. Furthermore a quality measure for HEB devices is set up by deriving the thermal coupling of the film to the substrate and the achieved critical current density from measured current-voltage characteristics.

•Mar 1, 1998•8 citations

A Distributed Device Model for Phonon-Cooled HEB Mixers Predicting IV Characteristics, Gain, Noise and IF Bandwidth

P. Khosropanah, H. Merkel, Sigfrid Yngvesson +3 more

A distributed model for phonon-cooled superconductor hot electron bolometer (HEB) mixers is given, which is based on solving the one-dimensional heat balance equation for the electron temperature profile along the superconductor strip. In this model it is assumed that the LO power is absorbed uniformly along the bridge but the DC power absorption depends on the local resistivity and is thus not uniform. The electron temperature dependence of the resistivity is assumed to be continuous and has a Fermi form. These assumptions are used in setting up the non-linear heat balance equation, which is solved numerically for the electron temperature profile along the bolometer strip. Based on this profile the resistance of the device and the IV curves are calculated. The IV curves are in excellent agreement with measurement results. Using a small signal model the conversion gain of the mixer is obtained. The expressions for Johnson noise and thermal fluctuation noise are derived. The calculated results are in close agreement with measurements, provided that one of the parameters used is adjusted.

Softwaretechnik-Trends•May 1, 2000•18 citations

Linear and nonlinear characteristics of NbN hot electron bolometer devices

Yan Zhuang

The superconducting HEB device is so far the most promising low noise mixer in the THz frequency range. It out-performs other existing receiver systems because it has low noise temperature and sufficient bandwidth for applications in the FIR range such as astronomy, remote sensing and plasma diagnostics. This work investigates the linear and nonlinear characteristics of NbN Hot Electron Bolometer (HEB) devices. First of all, a thorough expression of the Johnson noise and the thermal fluctuation noise has been re-derived. Our circuit model is more preferable for the HEB devices than the traditional one being used for the semiconductor bolometer. Secondly, the equivalent noise temperature of our receiver system has been significantly improved: the noise temperature went from the original 5800K to a record of 500K for silicon substrate devices. We are also getting improved noise performance for the new MgO substrate devices. The simulation results agree with the measured data very well around the optimum operating point. Finally, the device in the unstable region can be stabilized by connecting a series resistor with higher resistance than the negative resistance of the device. Two frequencies are related to the oscillation waveforms of the voltage and the current of the device. The first one is the repetition frequency that is actually related to the external circuit. The second one is the relaxation frequency that is related to the intrinsic phenomena of the device itself. The domain wall velocity and the relaxation oscillation frequency have been calculated both theoretically and experimentally. The calculated results are within a satisfactory range compared with the measured data. Also, a thorough explanation of the device oscillation process has been presented.

Journal of Bioresource Management•Jan 1, 2002•4 citations

Reduced noise in NbN hot-electron bolometer mixers by annealing

Z Q Yang, Merlijn Hajenius, J. J. A. Baselmans +3 more

We find that the sensitivity of heterodyne receivers based on superconducting hot-electron bolometers (HEBs) increases by 25?30% after annealing at 85??C in vacuum. The devices studied are twin-slot antenna coupled mixers with a small NbN bridge of 1 ? 0.15??m2. We show that annealing changes the device properties as reflected in sharper resistive transitions of the complete device, apparently reducing the device-related noise. The lowest receiver noise temperature of 700?K is measured at a local oscillator frequency of 1.63?THz and a bath temperature of 4.3?K.

Superconductor Science and Technology•Jan 31, 2006•10 citations

Optimized Sensitivity of NbN Hot Electron Bolometer Mixers by Annealing

Merlijn Hajenius, Z.Q. Yang, J. R. Gao +4 more

We report that the heterodyne sensitivity of superconducting hot-electron bolometers (HEBs) increases by 25-30% after annealing at 85degC in high vacuum. The devices studied are twin-slot antenna coupled mixers with a small area NbN bridge of 1 mum times 0.15 mum, above which there is a SiO2passivation layer. The mixer noise temperature, gain, and resistance versus temperature curve of a HEB before and after annealing are compared and analysed. We show that the annealing reduces the intrinsic noise of the mixer by 37% and makes the superconducting transition of the bridge and the contacts sharper. We argue that the reduction ofthe noise is mainly due to the improvement of the transparency of the contact/film interface. The lowest receiver noise temperature of 700 K is measured at a local oscillator frequency of 1.63 THz and at a bath temperature of 4.2 K.

IEEE Transactions on Applied Superconductivity•Jun 1, 2007•7 citations
Hot-electron bolometer devices, used successfully in low noise heterodyne mixing at frequencies up to 2.5 THz, have been analyzed. A distributed temperature numerical model of the NbN bridge, based on a local electron and a phonon temperature, is used to model pumped IV curves and understand the physical conditions during the mixing process. We argue that the mixing is predominantly due to the strongly temperature dependent local resistivity of the NbN. Experimentally we identify the origins of different transition temperatures in a real HEB device, suggesting the importance of the intrinsic resistive transition of the superconducting bridge in the modeling.
Improved and reproducible heterodyne mixing (noise temperatures of 950 K at 2.5 THz) has been realized with NbN based hot-electron superconducting devices with low contact resistances. A distributed temperature numerical model of the NbN bridge, based on a local electron and a phonon temperature, has been used to understand the physical conditions during the mixing process. We find that the mixing is predominantly due to the exponential rise of the local resistivity as a function of electron temperature.
Phonon cooled hot electron bolometers (HEB) show smaller noise temperatures in mixer applications above 1THz compared to Schottky diodes or SIS devices. To determine the optimal bias point for maximum IF bandwidth and lowest noise of a FEB detailed understandin g of the current-voltage characteristic is indispensable. A complete nonlinear model for a hot electron bolometric (HEB) mixer is derived. The dynamic resistance of a superconducting film is calculated under stron g demagnetization conditions. The resistance is modeled due to vortex flow and phase slip lines. Self heating gives rise to normal domains in the film. In addition the resistance due to thermally activated flux creep and thermal fluctuations is taken into account. All these relations form a large si gnal model for the iv-characteristics and the bias points of the device. A small signal linearization yields then conversion gain and noise temperatures. Furthermore a quality measure for HEB devices is set up by deriving the thermal coupling of the film to the substrate and the achieved critical current density from measured current-voltage characteristics.
A distributed model for phonon-cooled superconductor hot electron bolometer (HEB) mixers is given, which is based on solving the one-dimensional heat balance equation for the electron temperature profile along the superconductor strip. In this model it is assumed that the LO power is absorbed uniformly along the bridge but the DC power absorption depends on the local resistivity and is thus not uniform. The electron temperature dependence of the resistivity is assumed to be continuous and has a Fermi form. These assumptions are used in setting up the non-linear heat balance equation, which is solved numerically for the electron temperature profile along the bolometer strip. Based on this profile the resistance of the device and the IV curves are calculated. The IV curves are in excellent agreement with measurement results. Using a small signal model the conversion gain of the mixer is obtained. The expressions for Johnson noise and thermal fluctuation noise are derived. The calculated results are in close agreement with measurements, provided that one of the parameters used is adjusted.
The superconducting HEB device is so far the most promising low noise mixer in the THz frequency range. It out-performs other existing receiver systems because it has low noise temperature and sufficient bandwidth for applications in the FIR range such as astronomy, remote sensing and plasma diagnostics. This work investigates the linear and nonlinear characteristics of NbN Hot Electron Bolometer (HEB) devices. First of all, a thorough expression of the Johnson noise and the thermal fluctuation noise has been re-derived. Our circuit model is more preferable for the HEB devices than the traditional one being used for the semiconductor bolometer. Secondly, the equivalent noise temperature of our receiver system has been significantly improved: the noise temperature went from the original 5800K to a record of 500K for silicon substrate devices. We are also getting improved noise performance for the new MgO substrate devices. The simulation results agree with the measured data very well around the optimum operating point. Finally, the device in the unstable region can be stabilized by connecting a series resistor with higher resistance than the negative resistance of the device. Two frequencies are related to the oscillation waveforms of the voltage and the current of the device. The first one is the repetition frequency that is actually related to the external circuit. The second one is the relaxation frequency that is related to the intrinsic phenomena of the device itself. The domain wall velocity and the relaxation oscillation frequency have been calculated both theoretically and experimentally. The calculated results are within a satisfactory range compared with the measured data. Also, a thorough explanation of the device oscillation process has been presented.
We find that the sensitivity of heterodyne receivers based on superconducting hot-electron bolometers (HEBs) increases by 25?30% after annealing at 85??C in vacuum. The devices studied are twin-slot antenna coupled mixers with a small NbN bridge of 1 ? 0.15??m2. We show that annealing changes the device properties as reflected in sharper resistive transitions of the complete device, apparently reducing the device-related noise. The lowest receiver noise temperature of 700?K is measured at a local oscillator frequency of 1.63?THz and a bath temperature of 4.3?K.
We report that the heterodyne sensitivity of superconducting hot-electron bolometers (HEBs) increases by 25-30% after annealing at 85degC in high vacuum. The devices studied are twin-slot antenna coupled mixers with a small area NbN bridge of 1 mum times 0.15 mum, above which there is a SiO2passivation layer. The mixer noise temperature, gain, and resistance versus temperature curve of a HEB before and after annealing are compared and analysed. We show that the annealing reduces the intrinsic noise of the mixer by 37% and makes the superconducting transition of the bridge and the contacts sharper. We argue that the reduction ofthe noise is mainly due to the improvement of the transparency of the contact/film interface. The lowest receiver noise temperature of 700 K is measured at a local oscillator frequency of 1.63 THz and at a bath temperature of 4.2 K.