Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Digital SQUIDs: New definitions and results

Vasili K. Semenov

Published Jun 1, 2003• 30 citations
Publisher

Abstract

Recently we found that several simple SFQ circuits (normally used as ADC comparators) dramatically outperform conventional SQUIDs in time resolution and slew rate. For example, it is possible to reach a resolution of about a few percent of flux quantum by using a single-shot measurement that takes only a few picoseconds. All these SFQ circuits produce during each clock period only one bit of information that indicates whether the applied flux is larger or smaller the threshold. As a result it is natural to call them digital (or logic) SQUIDs. The new sensors can be used to detect a direction of the electrical current induced in a superconductor loop by the external field and digitally compensated by another SFQ devices. This composite device contains two kinds of digital components and also could be called a Digital SQUID. It has a limited practical value with a hundreds MHz clock rate. Fortunately, the clock frequency could be increased to tens of GHz. But in this case the third digital device (a decimation filter) should be added to filter out off-band noise and reduce the output clock frequency. The last device is rather similar to an ADC and also could be called a Digital SQUID. It is easy to show that the last Digital SQUID has a practically unlimited slew rate and dynamic range without suffering significant loss of energy sensitivity of the conventional two-junction SQUID.

DOI
10.1109/tasc.2003.814027

Related papers

Design and Performance of Digital SQUID with Sub-Flux Quantum Resolution

Hiroaki Myoren, Kouhei Takatoku, Masato Naruse +1 more

Digital SQUIDs based on the single flux quantum (SFQ) logic have attractive characteristics, such as wide dynamic range and high slew rate. However, the resolution of digital SQUIDs is limited to SFQ. To realize sub-flux quantum resolution for these SQUIDs, we have adopted two types of feedback combinations: one with the SFQ input/output for a main loop and the other with a mutually coupled loop. The main loop receives direct Φ0feedback and sub-flux quantum feedback Φ0/n, where n is an integer, from the mutually coupled loop. We confirmed the correct operation of our device at a clock frequency of 1.25 GHz for a digital SQUID with a sub-Φ0flux feedback resolution of Φ0/8 from circuit simulation. The slew rate is found to be 1.56×108Φ0/s in this simulation (fc=1.25 GHz, n=8). The flux resolution for the digital SQUID shows improvement with increasing n and reached below 40 mΦ0with n=210; however the slew rate is decreased with increasing n and reached 1.22×106Φ0/swith fc=1.25 GHz and n=210.

IEEE International Superconductive Electronics Conference (ISEC)•Jul 1, 2015•2 citations

Characterization of a digital squid for magnetic field measurements with high dynamic range

Imke Haverkamp, Olaf Wetzstein, J. Kunert +3 more

Measurements of extremely weak magnetic fields in unshielded environments require sensors providing a high dynamic range and slew rate while maintaining a high resolution. At present, analog Superconducting Quantum Interference Devices (SQUIDs) are the most sensitive sensors for magnetic flux. Due to their room-temperature feedback electronics necessary to maintain a stable point of operation, slew rates of those sensors are limited. The dynamic range is usually restricted by the resolution of classical analog to digital converters. The digital SQUID follows a different approach: a change of the magnetic field penetrating the pickup loop is translated by the sensor into a stream of voltage pulses. Each pulse represents the change of the magnetic flux inside the pickup loop by one flux quantum Φ0. By fast counting of these flux quanta, it is possible to outperform the analog SQUID in terms of dynamic range and maximum slew rate. We present our latest results with respect to the internal mechanisms of the digital SQUID and present a method to compensate the main source for nonlinear behavior of the sensor. The analyzed circuit was fabricated by FLUXONICS Foundry (1) in a 1 kA/cm² niobium fabrication process.

Elektronika : konstrukcje, technologie, zastosowania•Jan 1, 2011•1 citation

Experimental analysis of a digital SQUID device at 4.2 K

Torsten Reich, Thomas Ortlepp, Friedrich Uhlmann +1 more

The application of superconducting rapid single-flux quantum (RSFQ) digital electronics for highly sensitive measurement of magnetic fields can provide significant advantages in the use of conventional analogue SQUIDs, especially in terms of operation speed and dynamic range. Furthermore, utilizing an unconventional generalized single-flux-quantum (SFQ) logic with a bidirectional operation principle allows an additional decrease in effort in superconducting electronics. Our novel fully digital SQUID based on the SFQ technique can be assumed to be operating at frequencies in the gigahertz range corresponding to slew rates of several 10^9 Φ0/s. We present first experimental results for the proper digital function as a preliminary stage for a digital SQUID magnetometer device. The measurements presented are performed for a reliable low temperature superconductor technology at liquid helium temperature; nevertheless the very low complexity of the superconducting digital circuitry holds promise as regards prospects for a working digital SQUID based on high temperature superconductor technology.

Superconductor Science and Technology•Jun 20, 2005•18 citations

Analysis of superconducting analog-to-digital converter front-end for improved resolution and large dynamic range

Pascal Febvre, Héla Gassara, Patricia Desgreys +1 more

Analog-to-digital converters (ADCs) are key components of most digital systems, as the necessary interface between the analogue world to send and receive signals. Semiconductor ADC systems are intrinsically limited to low frequency ranges of a few GHz and associated to dynamic ranges limited by linearity issues. Superconductor electronic ADCs rely on the magnetic flux quantization and do not suffer from the linearity issues. Moreover, the Rapid-Single-Flux Quantum (RSFQ) technique [1] allows the sampling of signals far in the microwave range, of the order of 100 GHz for the fastest circuits with state-of-the-art low critical temperature niobium-based technology.Two main applications require the use of fast and high dynamic range superconducting ADCs: future ground- or space-based telecommunication systems for software defined radio (SDR) and all systems requiring very high dynamic range in the 120-180 dB range. In this last category, one can find the digital Superconducting Quantum Interference Devices (SQUIDs) that combine the digitization due to the RSFQ technique, with the ultrasensitive sensing of magnetic fields, that are of interest for several applications, ranging from Non-Destructive Evaluation (NDE) to the detection of faint geomagnetic signatures [2].In this work, we will describe in details an analysis of performances of two different kinds of ADCs, respectively for space and geophysics applications. New designs with their electrical circuits will be described for operation in the microwave frequency band with a sigma-delta architecture, and for improved dynamic range with a delta design. The performance in terms of number of bits or dynamic range, frequency bandwidth and ultimate sampling speed will be compared with the ones of existing ADCs. Considerations about the layout due to technological considerations are taken into account in the design. Trade-offs between performance and technologies will be emphasized.[1] K. Likharev and V. Semenov, IEEE Trans. Appl. Supercond. 1, 3 (1991).[2] T. Reich, P. Febvre, T. Ortlepp, F. H. Uhlmann, J. Kunert, R. Stolz, and H.-G. Meyer, Journal of Applied Physics 104(2), 024509 (2008).

•Apr 25, 2010•0 citations

Performance of Digital SQUID with Sub-Flux Quantum Feedback Resolution Fabricated using 10 kA/cm2 Nb Process

Kohki Itagaki, Itta Oshima, Yuichi Hasegawa +4 more

Abstract Digital superconducting quantum interference device (SQUID with Single Flux Quantum (SFQ) feedback operates as a Δ-type oversampling A/D converter. Magnetic flux resolution at Nyquist frequency can be improved by taking sub SFQ feedback resolution and large oversampling ratio. Using high critical current density Nb process for fabricating SFQ circuits, we expected more higher operation speed for the digital SQUID and resulting to higher magnetic flux resolutions. We expected a performance of the digital SQUID magnetometer fabricated using 10 kA/cm2 Nb process based on CAD layout, with an up/down counter using T2FF cells and parallel SFQ feedback. For the clock frequency of 13 GHz and the Nyquist frequency of 1.587 MHz, the magnetic field noise was lower than 1.5 fT / Hz and the slew rate was exceeded 500 mT/s.

Journal of Physics Conference Series•Jul 1, 2020•0 citations

Design and Magnetic Field Noise of Magnetometer Using Digital SQUID With Subflux Quantum Feedback

Hiroaki Myoren, Kouhei Takatoku, Masato Naruse +1 more

Digital superconducting quantum interference devices (SQUIDs) based on single-flux quantum (SFQ) logic have attractive characteristics such as wide dynamic ranges and high slew rates. However, the resolution of a typical digital SQUID is limited by SFQ feedback. To realize lower magnetic field noise by magnetometers using digital SQUIDs, we have adopted two feedback combinations: one, utilizing the SFQ input/output for a main loop and the other, using a mutually coupled loop. The main loop receives direct Φ0feedback and subflux quantum feedback Φ0/n, where n is an integer from the mutually coupled loop. The flux resolution for the digital SQUID shows improvement with increasing n and reaches below 40 mΦ0at n = 210; however, the slew rate decreases with increasing n and reaches 1.22 × 106Φ0/s at fc= 1.25 GHz and n = 210. For a magnetometer using a digital SQUID with a pickup loop, we confirmed a magnetic field noise of less than 100 fT/√Hz with a signal bandwidth of 1 MHz for operation frequency fcof 20 GHz.

IEEE Transactions on Applied Superconductivity•May 20, 2016•7 citations
Recently we found that several simple SFQ circuits (normally used as ADC comparators) dramatically outperform conventional SQUIDs in time resolution and slew rate. For example, it is possible to reach a resolution of about a few percent of flux quantum by using a single-shot measurement that takes only a few picoseconds. All these SFQ circuits produce during each clock period only one bit of information that indicates whether the applied flux is larger or smaller the threshold. As a result it is natural to call them digital (or logic) SQUIDs. The new sensors can be used to detect a direction of the electrical current induced in a superconductor loop by the external field and digitally compensated by another SFQ devices. This composite device contains two kinds of digital components and also could be called a Digital SQUID. It has a limited practical value with a hundreds MHz clock rate. Fortunately, the clock frequency could be increased to tens of GHz. But in this case the third digital device (a decimation filter) should be added to filter out off-band noise and reduce the output clock frequency. The last device is rather similar to an ADC and also could be called a Digital SQUID. It is easy to show that the last Digital SQUID has a practically unlimited slew rate and dynamic range without suffering significant loss of energy sensitivity of the conventional two-junction SQUID.
Digital SQUIDs based on the single flux quantum (SFQ) logic have attractive characteristics, such as wide dynamic range and high slew rate. However, the resolution of digital SQUIDs is limited to SFQ. To realize sub-flux quantum resolution for these SQUIDs, we have adopted two types of feedback combinations: one with the SFQ input/output for a main loop and the other with a mutually coupled loop. The main loop receives direct Φ0feedback and sub-flux quantum feedback Φ0/n, where n is an integer, from the mutually coupled loop. We confirmed the correct operation of our device at a clock frequency of 1.25 GHz for a digital SQUID with a sub-Φ0flux feedback resolution of Φ0/8 from circuit simulation. The slew rate is found to be 1.56×108Φ0/s in this simulation (fc=1.25 GHz, n=8). The flux resolution for the digital SQUID shows improvement with increasing n and reached below 40 mΦ0with n=210; however the slew rate is decreased with increasing n and reached 1.22×106Φ0/swith fc=1.25 GHz and n=210.
Measurements of extremely weak magnetic fields in unshielded environments require sensors providing a high dynamic range and slew rate while maintaining a high resolution. At present, analog Superconducting Quantum Interference Devices (SQUIDs) are the most sensitive sensors for magnetic flux. Due to their room-temperature feedback electronics necessary to maintain a stable point of operation, slew rates of those sensors are limited. The dynamic range is usually restricted by the resolution of classical analog to digital converters. The digital SQUID follows a different approach: a change of the magnetic field penetrating the pickup loop is translated by the sensor into a stream of voltage pulses. Each pulse represents the change of the magnetic flux inside the pickup loop by one flux quantum Φ0. By fast counting of these flux quanta, it is possible to outperform the analog SQUID in terms of dynamic range and maximum slew rate. We present our latest results with respect to the internal mechanisms of the digital SQUID and present a method to compensate the main source for nonlinear behavior of the sensor. The analyzed circuit was fabricated by FLUXONICS Foundry (1) in a 1 kA/cm² niobium fabrication process.
The application of superconducting rapid single-flux quantum (RSFQ) digital electronics for highly sensitive measurement of magnetic fields can provide significant advantages in the use of conventional analogue SQUIDs, especially in terms of operation speed and dynamic range. Furthermore, utilizing an unconventional generalized single-flux-quantum (SFQ) logic with a bidirectional operation principle allows an additional decrease in effort in superconducting electronics. Our novel fully digital SQUID based on the SFQ technique can be assumed to be operating at frequencies in the gigahertz range corresponding to slew rates of several 10^9 Φ0/s. We present first experimental results for the proper digital function as a preliminary stage for a digital SQUID magnetometer device. The measurements presented are performed for a reliable low temperature superconductor technology at liquid helium temperature; nevertheless the very low complexity of the superconducting digital circuitry holds promise as regards prospects for a working digital SQUID based on high temperature superconductor technology.
Analog-to-digital converters (ADCs) are key components of most digital systems, as the necessary interface between the analogue world to send and receive signals. Semiconductor ADC systems are intrinsically limited to low frequency ranges of a few GHz and associated to dynamic ranges limited by linearity issues. Superconductor electronic ADCs rely on the magnetic flux quantization and do not suffer from the linearity issues. Moreover, the Rapid-Single-Flux Quantum (RSFQ) technique [1] allows the sampling of signals far in the microwave range, of the order of 100 GHz for the fastest circuits with state-of-the-art low critical temperature niobium-based technology.Two main applications require the use of fast and high dynamic range superconducting ADCs: future ground- or space-based telecommunication systems for software defined radio (SDR) and all systems requiring very high dynamic range in the 120-180 dB range. In this last category, one can find the digital Superconducting Quantum Interference Devices (SQUIDs) that combine the digitization due to the RSFQ technique, with the ultrasensitive sensing of magnetic fields, that are of interest for several applications, ranging from Non-Destructive Evaluation (NDE) to the detection of faint geomagnetic signatures [2].In this work, we will describe in details an analysis of performances of two different kinds of ADCs, respectively for space and geophysics applications. New designs with their electrical circuits will be described for operation in the microwave frequency band with a sigma-delta architecture, and for improved dynamic range with a delta design. The performance in terms of number of bits or dynamic range, frequency bandwidth and ultimate sampling speed will be compared with the ones of existing ADCs. Considerations about the layout due to technological considerations are taken into account in the design. Trade-offs between performance and technologies will be emphasized.[1] K. Likharev and V. Semenov, IEEE Trans. Appl. Supercond. 1, 3 (1991).[2] T. Reich, P. Febvre, T. Ortlepp, F. H. Uhlmann, J. Kunert, R. Stolz, and H.-G. Meyer, Journal of Applied Physics 104(2), 024509 (2008).
Abstract Digital superconducting quantum interference device (SQUID with Single Flux Quantum (SFQ) feedback operates as a Δ-type oversampling A/D converter. Magnetic flux resolution at Nyquist frequency can be improved by taking sub SFQ feedback resolution and large oversampling ratio. Using high critical current density Nb process for fabricating SFQ circuits, we expected more higher operation speed for the digital SQUID and resulting to higher magnetic flux resolutions. We expected a performance of the digital SQUID magnetometer fabricated using 10 kA/cm2 Nb process based on CAD layout, with an up/down counter using T2FF cells and parallel SFQ feedback. For the clock frequency of 13 GHz and the Nyquist frequency of 1.587 MHz, the magnetic field noise was lower than 1.5 fT / Hz and the slew rate was exceeded 500 mT/s.
Digital superconducting quantum interference devices (SQUIDs) based on single-flux quantum (SFQ) logic have attractive characteristics such as wide dynamic ranges and high slew rates. However, the resolution of a typical digital SQUID is limited by SFQ feedback. To realize lower magnetic field noise by magnetometers using digital SQUIDs, we have adopted two feedback combinations: one, utilizing the SFQ input/output for a main loop and the other, using a mutually coupled loop. The main loop receives direct Φ0feedback and subflux quantum feedback Φ0/n, where n is an integer from the mutually coupled loop. The flux resolution for the digital SQUID shows improvement with increasing n and reaches below 40 mΦ0at n = 210; however, the slew rate decreases with increasing n and reaches 1.22 × 106Φ0/s at fc= 1.25 GHz and n = 210. For a magnetometer using a digital SQUID with a pickup loop, we confirmed a magnetic field noise of less than 100 fT/√Hz with a signal bandwidth of 1 MHz for operation frequency fcof 20 GHz.